Renesas RH850 Series Istruzioni per l'installazione e il funzionamento

Application Note

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

RH850 Series

CAN Receive Procedure (CAN FD Mode)

Summary

This document describes an example of a procedure for receiving CAN using the RH850 series. Please refer to the

notes in the latest user's manual hardware edition for the settings of each register.

Operation Confirmed Devices

This document applies to the RH850 series.

The variables described in the text are as follows.

Table 1-1 Target Devices and Variables

Variable

Target MCU

RH850/E2x

RH850/E1M-S2

RH850/P1M-E

RS-CAN FD channel number

0~4

0~3

0~2

GAFLIDj, GAFLMj, GAFLP0j,

GAFLP1j Register numbers

0~15

Transmit/Receive FIFO buffer

number

0~14

0~11

0~8

Receive FIFO buffer number

0~7

Receive buffer number

0~79

0~63

0~47

Transmit buffer number

0~79

0~63

0~47

RAM test number

0~63

GAFLCFGi、GTINTSTSi

Number of each status register

0~2

0,1

The functions marked with "★" in the text are applicable to cases where 2 or more channels are installed.

In the text, CFD is omitted from the register names.

R01AN6028EJ0100

Rev.1.0

RH850 Series CAN Receive Procedure (CAN FD Mode)

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

Contents

1. Receive Function..............................................................................................................3

2. Receive Using Receive Buffers........................................................................................4

3. Receive Using Receive FIFO Buffers...............................................................................7

4. Receive Using Transmit/Receive FIFO Buffers...............................................................12

5. CAN-related Interrupt Processing...................................................................................18

6. Precautions for Processing Flow ....................................................................................19

7. Appendix........................................................................................................................20

RH850 Series CAN Receive Procedure (CAN FD Mode)

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

1. Receive Function

The functions that can be used when receiving CAN messages are shown below. For details on each process, refer to

the following chapters.

•・Receive using the receive buffer

•・Receive using the receive FIFO buffer

•・Receive using the transmit / receive FIFO buffer

RH850 Series CAN Receive Procedure (CAN FD Mode)

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

2. Receive Using Receive Buffers

Receive buffer q shared by all channels is available. Since the message stored in the receive buffer with the same

number is overwritten, the latest received data can be read.

If it is received in the receive buffer, no interrupt is generated.

When the process of storing the received message in the receive buffer starts, the receive buffer q becomes "new

message" (the RMNSq flag in the RMNDy register becomes "1"). Received data information can be read from the

RMIDq register, RMPTRq register, and RMDFb_q register (b = 0 to 4). The payload size that can be received by the

receive buffer is up to 20 bytes. You must use the receive or transmit / receive FIFO to receive messages exceeding 20

bytes.

For the configuration settings for using the receive buffer, refer to "CAN Configuration Application Note".

Figure 2-1 shows the operation of the receive buffer.

Figure 2-1 Receive Buffer Operation

Msg1

Msg2

Msg3

Msg1

Msg2

Read with

the program

Msg3

CAN Bus

Receive Rule Table

Receive buffer 0

Receive buffer 1

Receive buffer 2

Receive buffer q*

Msg1

Msg2

Msg3

【Note】q：Number of receive buffers (set value of the NRXMB [7: 0] bit of the RMNB register) -1

Receive

Data

RH850 Series CAN Receive Procedure (CAN FD Mode)

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

2.1 Receive Buffer Read Procedure

Figure 2-2 shows the procedure for reading the receive buffer.

【Note】

Write “0” for the RMNSq flag in the RMNDy register in global operation mode or global test mode.

To set the RMNSq flag to “0”, write “0” with the program.

To write "0" in the RMNSq flag, use the store instruction to write "0" in the bit you want to set to "0" and "1"

in the other bits.

The RMNSq flag cannot be set to “0”while the message is being stored. The time to store a message depends

on the size of the payload stored in the receive buffer.

For a standard ID, read b10 to b0 of the ID (the RMID [28: 0] bit of the RMIDq register). “0”can be read for

b28 to b11.

START

Yes

Is there a receive buffer that received

a new message?

Clear the receive buffer receive completion flag

corresponding to the receive buffer to "0"*1.、2.、3.、4.

Yes

Corresponding receive buffer receive complete

Is the flag "0"?*4.

Read messages in the receive buffer

・IDE/RTR/ID*5.

・DLC*6.

・Label information of received data*7.

・Timestamp value

・Received data*8.

Yes

Is there overwriting of

the message being read?

(Corresponding receive buffer receive completed

Is the flag "1"? )

User processing when message overwrite is detected

END

RH850 Series CAN Receive Procedure (CAN FD Mode)

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

If DLC replacement is enabled after filtering by the reception rule (the DCE bit of the GCFG register is “1”,

DRE bit is “1”), the received message matches the DLC set value in the reception rule table (the

GAFLDLC[3:0] bit of the GAFLP0_j register) that matches the received message is stored. Otherwise, the

DLC value of the received message is stored.

After filtering by the receive rule, the set value of the label of the receive rule table (the GAFLPTR [11: 0] bit

of the GAFLP0_j register) that matches the received message is stored.

If the DLC of the received message (the value of the RMPLC [3: 0] bit of the RMPTRq register) is less than

the payload storage size of the receive buffer, “H'00”can be read for the data byte (RMDFb_q register) for

which no data is set.

Figure 2-2 Receive Buffer Read Procedure

RH850 Series CAN Receive Procedure (CAN FD Mode)

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

3. Receive Using Receive FIFO Buffers

There are 8 receive FIFO buffers shared by all channels. Messages can be stored in each receive FIFO buffer for the

number of buffers.

When a received message is stored in the receive FIFO buffer, the value of the corresponding message count display

counter (the RFMC [7: 0] bit of the RFSTSx register) is incremented.

Received messages can be read from the RFIDx register, RFPTRx register, RFFDSTSx register, and RFDFd_x

When the value of the message count display counter matches the buffer value of the FIFO buffer (the value set by

the RFCCx register RFDC [2: 0] bit), the receive FIFO buffer becomes full (the RFFLL flag in the RFSTSx register is

“1”). When all messages are read from the receive FIFO buffer, the receive FIFO buffer becomes empty (the RFEMP

flag in the RFSTSx register is “1”).

Refer to the CAN Configuration Application Note for configuration settings to use the receive FIFO buffer.

Figure 3-1 shows the operation of the receive FIFO buffer.

Figure 3-1 Receive FIFO Buffer Operation

Receive

FIFO

interrupt

source

activated

RFIDLm,Hx

RFTSmx

RFPTRx

RFDFx

Msg1

Msg2

Msg3

Msg4

Msg3

Read with the

program

Msg2

Receive FIFO

Buffer x

Msg4

Msg3

Msg2

Mag1

：When the receive FIFO interrupt source reaches “the condition set in (the RFIGCV [2: 0] bit of the

RFCCx register) "

(When the RFIM bit of the RFCCx register is “0”)

：Receive FIFO interrupt source is "every time one message is received"

(When the RFIM bit of the RFCCx register is “1”)

CAN Bus

Msg1

Msg4

Receive Rule Table

※

※：Number of receive FIFO

buffer stages: 4

An interrupt occurs when a

message is stored until 8/8

Received data

RH850 Series CAN Receive Procedure (CAN FD Mode)

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

3.1 Receive FIFO Buffer Read Procedure

Figure 3-2 shows the procedure for reading the receive FIFO buffer, and Figure 3-3 and Figure 3-4 show the

procedure for enabling and prohibiting the use of the receive FIFO buffer.

【Note】

If the FIFO message lost interrupt is enabled, execute it in the global error interrupt processing.

For standard ID, read b10-b0 of ID (the RFID [28: 0] bit of the RFIDx register). “0”can be read for b28-b11.

If DLC replacement is enabled after filtering by the reception rule (the DCE bit of the GCFG register is “1”,

DRE bit is “1”), the DLC set value in the reception rule table (the GAFLDLC[3:0] bit of the GAFLP0_j

stored.

After filtering by the reception rule, the set value of the receive rule table label (the GAFLPTR [11: 0] bit of

GAFLP0_j) that matches the received message is stored.

START

END

Yes

Unread message in the receive

FIFO buffer?*8.

Increment receive FIFO buffer pointer

*6.、7.

Read messages in the receive FIFO buffer

・IDE/RTR/ID*2.

・DLC*3.

・Label information of received data*4.

・Timestamp value

・Received data*5.

Yes

User processing when message overwrite is detected*1.

Is there a message lost?*1.

Clear receive FIFO message lost flag*1.

RH850 Series CAN Receive Procedure (CAN FD Mode)

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

If the DLC of the received message (value of the RFDLC [3: 0] bit of the RFPTRx register) is less than the

payload storage size of the receive FIFO buffer, "H'00" can be read for the data byte (RFDFb_x register) for

which no data is set.

After reading the messages in the receive FIFO buffer (RFIDx register, RFPTRx register, RFDFb_x register),

increment the pointer (write "H'FF" to the RFCC [7: 0] bit of the RFIDCTRx register).

Increment the pointer when the receive FIFO buffer is used (the RFE bit of the RFCCx register is “1”) and

there are unread messages in the receive FIFO buffer (the RFEMP flag in the RFSTSx register is “0”).

When reading all the unread messages in the receive FIFO buffer, use a loop statement or the like to read

until the buffer is empty.

Figure 3-2 Receive FIFO Buffer Read Procedure (no interrupt used)

RH850 Series CAN Receive Procedure (CAN FD Mode)

R01AN6028EJ0100 Rev.1.0 Page

of 26

May 10, 2017

【Note】

Rewrite to enable/disable the receive FIFO buffer (the RFE bit of the RFCCx register) in the global

operation mode or global test mode.

Make the configuration settings for using the receive FIFO buffer, and then enable the use of the receive

FIFO buffer (the RFE bit is "1").

If the number of receive FIFO buffers is set to “0” (“B’000” in the RFDC [2: 0] bit of the RFCCx register),

do not allow the receive FIFO buffer to be used.

Figure 3-3 Procedure to Enable Receive FIFO Buffer Use

【Note】

Rewrite to enable/disable the receive FIFO buffer (the RFE bit of the RFCCx register) in the global

operation mode or global test mode.

Even if the use of the receive FIFO buffer is prohibited (the RFE bit is “0”) while an interrupt request is

generated (the RFIF flag in the RFSTSx register is “1”), the interrupt request flag (RFIF flag) is not

automatically set to “0”. Set the interrupt request flag to "0" with the program.

Figure 3-4 Procedure to Prohibit Receive FIFO Buffer Use

START

Prohibit use of receive FIFO buffer*1.、2.

END

START

Yes

Is the receive FIFO buffer empty?

Enable use of receive FIFO buffer*1.、2.、3.

END

Altri manuali per RH850 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Renesas Hardware per computer

Renesas

Renesas H8/3864 Series Manuale utente

Renesas

Renesas 3803L Manuale utente

Renesas

Renesas RL78/G13 Istruzioni per l'installazione e il funzionamento

Renesas

Renesas M34553T-PTCA Manuale utente

Renesas

Renesas RA6 Series Manuale utente

Renesas

Renesas PFESiP/V850EP1 Manuale utente

Renesas

Renesas RH850 Series Manuale utente

Renesas

Renesas DA16200 PMOD Manuale utente

Renesas

Renesas Emulator MCU Board for 38D5 Group... Manuale utente

Renesas

Renesas R8C/1B Manuale utente

Renesas

Renesas H8/38099 Manuale utente

Renesas

Renesas RTE7701201CFK144T000R Manuale utente

Renesas

Renesas H8/36902 Series Manuale utente

Renesas

Renesas H8S/2646 Series Manuale utente

Renesas

Renesas Renasas Single-Chip Microcomputer SH7086 Manuale utente

Renesas

Renesas R0E000010ACB10 Manuale utente

Renesas

Renesas M3062PT-EPB Manuale utente

Renesas

Renesas H8S series Manuale utente

Renesas

Renesas SuperH E10A Manuale utente

Renesas

Renesas SH7206 Manuale utente

Renesas

Renesas Hitachi H8S/2194 Series Manuale utente

Renesas

Renesas IE850A Manuale utente

Renesas

Renesas R0E436640CPE00 Manuale utente

Renesas

Renesas RL78 Series Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente