Renesas M32C/8x StarterKit Plus Manuale utente

onlinecomponents.com

Analog

Adjust (R16)

Power

LED

Reset

Switch

User

Switches

Thermistor

8 Characters x 2 Lines LCD

LCD

Contrast

User LEDs

M32C/8x

ICD LED Status:

Red – Target Stopped

Green – Target Running

Status – ICD Status

Red – ICD Power

RTA-FoUSB-MON

In-Circuit Debugger

(ICD)

Target/Bus

Power Mode

Selector

M32C/8x StarterKit Plus QuickStart Guide, rev. 2.0 Page 1 of 5

Figure 1. M32C/8x SKP

QuickStart Guide M32C/8x

StarterKit Plus

SKP32C83, SKP32C84

SKP32C85

onlinecomponents.com

1. M32C/8x SKP StarterKit Plus Software Install

a) Please insert the enclosed CD into your computer’s CD-ROM drive. The CD should auto-start, displaying the SKP Picker

Install Screen. Follow the directions in the installation windows to install the Renesas tools.

i) If the installation screen does not appear, please browse the CD root folder and double-click on “SKP-Installer.exe”.

– Do not plug the In-Circuit Debugger into your USB port until instructed to in Section 2, USB Driver Installation.

– The installation process requires a valid SKP serial number. Locate the label on the PC board or on the

side of your box.

– During the installation process, you may be prompted to restart your computer. Do not restart until the SKP installer

has completed installation of all of the software items.

– During the SKP install, dialog boxes will appear asking if you would like to install the development tools or not.

The development tools will allow you to evaluate the different features of the M32C MCU and the software

development environment (debugger, compiler, linker, etc…).

2. USB Driver Installation

You need to install the driver for the RTA-FoUSB-MON In-Circuit Debugger (ICD) before you can use it. First, verify that the

Target/Bus Power Mode switch is in the USB position.

Next, connect one end of the mini USB cable into the ICD and the other end into your PC’s USB port. The red “Power” LED

on the ICD will light up and the yellow “Status” LED will blink about 2-3 times per second.

If you are running Windows 98, ME or 2000, no intervention by the user is needed. When the ICD is plugged in, Windows

automatically attaches the correct driver for your device and it is ready to use.

If you are running Windows XP, the first time a FoUSB device is plugged into a different USB port on the PC,

the Windows XP “Found New Hardware Wizard” window will appear. Select the default option “Install the software

automatically (recommended)”.

Windows will then begin installing the USB driver. Another screen may appear stating that this driver has not been XP

certified by Microsoft because we did not participate in Microsoft XP driver certification. Click the “Continue Anyway” button.

Your driver is now installed. Click Finish to close the wizard.

The driver files (.sys and .inf) are always located under the FoUSB install directory (For example: C:\MTOOL\FoUSB\USB

Drivers\) in case you are have trouble with the automatic driver installer.

NOTE: If you have problems installing the drivers or your PC will not recognize the ICD, please see the "Troubleshooting"

section of the RTA-FoUSB-MON user’s manual for details.

Figure 2. M32C/8x SKP System Connectivity

M32C/8x StarterKit Plus QuickStart Guide, rev. 2.0 Page 2 of 5

M32C/8x SKP

10-pin

Target

Cable

PC with Windows®98SE,

2000, Me, or XP

ICD

Mini USB

Cable

onlinecomponents.com

3. Demo Program

The following instructions are specific for the SKP32C85 kit. Substitute 83 or 84 in place of 85 for the SKP32C83 or SKP32C84

kit respectively. The kit ships with a demo program that runs on the board when connected to the ICD (RTA-FoUSB-MON).

a) If not already done in step 2a), plug one end of the USB cable into the RTA-FoUSB-MON and the other into a USB socket

on your PC.

b) Connect the RTA-FoUSB-MON to the SKP board using the supplied ribbon cable. The power light of the board should

come on. If the power light on the SKP board does not come on, check the Power Mode switch on the RTA-FoUSB-MON

and verify that it is set to the “USB” position.

c) Press the reset switch to run the demo program.

– The LCD on the board will display a welcome message (adjust LCD contrast as needed). After a few seconds,

“RT1: xxxx, AN0: xxxx” will be displayed on the LCD.

– The LED’s will blink sequentially (back and forth).

– The LED flash rate is controlled by the Analog Adjust (R16) potentiometer (which is connected to the ADC’s AN0 input).

The 10-bit ADC value is also shown on the LCD as AN0.

d) Turn the Analog Adjust clockwise or counter-clockwise. This alters the flash rate of the LEDs, and increases or decreases

the AN0 value shown on the LCD.

e) Press the pushbutton switches S1, S2, or S3. This will stop the sequential blinking of the LEDs. The LED associated with

the pushbutton switch (i.e., S1 – Red LED, S2 – Yellow LED, and S3 – Green LED) will light up.

4. HEW (IDE) Quick-Start

HEW integrates various tools such as the compiler, assembler, debugger, and editor into a common Graphical User Interface.

To learn more on how to use HEW, open the HEW manual navigator on your computer (Start > (All) Programs > Renesas

High-performance Embedded Workshop > Manual Navigator).

a) Launch HEW from the Start menu (Start > (All) Programs > Renesas High-performance Embedded Workshop >

High-performance Embedded Workshop).

b) In the “Welcome!” dialog box:

i) Verify “Create a new project workspace” is selected.

ii) Click <OK>.

c) In the “New Project Workspace” Dialog box:

i) Verify the “CPU family” is set to “M32C”.

ii) Select “M32C/85 StarterKit Plus” (Figure 3).

iii) Enter “skptest85” for the Workspace Name (the Project

Name will auto fill to “skptest85”).

iv) Click <OK>.

d) On the “StarterKit Plus - Step 1” Window:

i) Click <Next>.

e) On the “StarterKit Plus - Step 2” Window:

i) Select “SKP Operational Test”.

ii) Click <Finish>.

f) In the “Project generator information” Window:

i) Click <OK>.

g) Click the “Build” icon, , to compile, assemble and

link the project. HEW will look similar to Figure 4.

h) After ensuring there are no errors, proceed to section 5, KD3083 Debugger Quick-Start.

M32C/8x StarterKit Plus QuickStart Guide, rev. 2.0 Page 3 of 5

Figure 3. New Project Workspace in HEW

Figure 4. HEW with the skptest85

project compiled

onlinecomponents.com

5. KD3083 (Debugger) Quick-Start

a) Connect the SKP to the PC as shown in Figure 2 (described in

detail in steps 3a) and 3b) above).

b) Click on the debugger button to launch the KD3083

debugger from HEW. The “Init” dialog box should open (Figure 5).

c) The first time you run KD3083, you will have to define the target:

i) Click <Refer…>.

ii) Select MCU as follows using Table 1.

– Select the group corresponding to the SKP MCU.

– Select the MCU in the group.

iii) Select “USB” and click <OK>.

– If you get an error,

check connectivity.

– If the message “We should download new firmware”

is displayed, click <OK>.

d) After initialization, the KD3083 Program Window will appear and

our program, “skptest85.x30”, is automatically downloaded.

The KD3083 Program Window should look like Figure 6.

e) Click the “Go” icon to start the program. This program

is similar to the Demo program, but the LEDs do not blink.

The LED’s are off unless any of the user switches are pressed.

f) Click the “Stop” icon to halt the program. If you now

click the “Go” icon, the program will resume

execution from the point it stopped.

g) Exit KD3083 by selecting “File > Exit” from the pull-down

menu in KD3083.

h) Exit HEW by selecting “File > Exit” from the pull-down menu in HEW.

6. Downloading (re-loading) the Demo Program using the Flash-over-USB™

Programmer

When we ran KD3083, the original demo program was erased and the SKP board was programmed with a different program.

You can use the Flash-over-USB™ Programmer to restore the original demo program.

a) Connect the SKP to the PC. (Described in detail in steps 3a) and 3b) above.)

b) Start the Flash-over-USB™ Programmer (Start > (All) Programs > RENESAS-TOOLS > Flash-over-USB Ver. x.xx > FoUSB

Programmer) or double-click on the “FoUSB” icon on your desktop).

c) The first time the FoUSB Programmer is run on your computer:

i) Click on “Select MCU” button.

ii) Select M32C/80 series.

iii) Then select the appropriate group and part number as shown in Table 1.

iv) Click <OK>.

v) Click <OK> as requested until you are returned to the Flash-over-USB main menu.

d) Each subsequent time the FoUSB Programmer is run:

– If the “Unlocked” window appears, click <OK>.

e) Click <Open> when the Flash-Over-USB main menu appears.

M32C/8x StarterKit Plus QuickStart Guide, rev. 2.0 Page 4 of 5

Figure 5. KD3083 Init Window

Figure 6. KD3083 Program Window after

download of skptest85

Table 1.

SKP32C83 – M30835FJ

SKP32C84 – M30845FJ

SKP32C85 – M30855FH

onlinecomponents.com

f) Browse to the “C:\MTOOL\SKP32C85\Sample_Code\SKP\

SKPDemo\Release” folder.

g) Select “SKPDemo.mot” and click <Open>.

i) When the ID Code dialog box appears, click <OK>.

h) Click <Program> to open the Program Flash window.

i) Click <Program> to download the demo program.

j) When the FoUSB dialog box “Program completed

Successfully” appears, click <OK> (Figure 7).

k) Click <Exit> to close Flash-over-USB Programmer

and the demo program should start.

For more information on how to use the Flash-over-USB™

Programmer, click on the “Help” button.

7. What’s the next step?

After you have completed this quick-start procedure, please review the tutorials that came with the kit. The tutorials will help

you understand and jumpstart the software development process using Renesas’ development tools.

You can access the tutorials from the Start Menu (Start > (All) Programs > RENESAS-TOOLS > SKP32C85 > Tutorial 1 –

Development Process or Tutorial 2 – Creating a New Project) or from (Start > (All) Programs > RENESAS-TOOLS >

SKP32C85 > Document Description), which also lists other documents that come with the SKP. To check for any updates

to the StarterKit Plus, use the (Start > (All) Programs > RENESAS-TOOLS > SKP32C85 > Check for Kit Updates) shortcut.

This will take you to a kit-specific page on the Renesas website which provides links to any available update downloads.

8. HEW3/C-Compiler

The High-performance Embedded Workshop User Manual will show you how HEW3 integrates various tools such as the

compiler, assembler, debugger and editor into a common Graphical User Interface. To access the manual on your computer,

go to the HEW menu (Start > (All) Programs > Renesas High-performance Embedded Workshop > Manual Navigator).

The NC308WA v.5.20 Entry version of the C-compiler included in the SKP has no time expiration, but has the following limits:

1. Assembly optimization and debug options are not available.

2. The tool to analyze the inspector or variable is not available.

3. Some advanced tool functions, such as the map viewer, are not available.

4. The software comes without support or warranty.

5. See NC308WA v.5.20 User’s Manual for further details.

If your development needs exceed the above limitations, please go to the following web site, http://download.renesas.com/

eng/mpumcu/evaluation_software/compilers_and_assemblers/m3t_nc308wa/index.html and download the full version

(4 calendar month trial).

M32C/8x StarterKit Plus QuickStart Guide, rev. 2.0 Page 5 of 5

subsidiary of Renesas Technology Corporation. All trademarks are the property of their respective

owners. The information supplied by Renesas Technology America, Inc. is believed to be accurate

and reliable, but in no event shall Renesas Technology America, Inc. be liable for any damages

whatsoever arising out of the use or inability to use the information or any errors that may appear in

this publication. The information is provided as is without any warranties of any kind, either express

or implied. Renesas Technology America, Inc. reserves the right, without notice, to make changes

to the information or to the design and specifications of its hardware and/or software products.

Products subject to availability. Printed in U.S.A.

Renesas Technology America, Inc.

450 Holger Way

San Jose, CA 95134-1368

Phone: 408-382-7500

Fax: 408-382-7501

www.renesas.com

Figure 7. Flash-over-USB™ Programmer

Main Menu after loading the Demo Code

If you require additional information or assistance, please send an

email to [email protected].

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Renesas Microcontrollore

Renesas

Renesas RZ/N1S Manuale utente

Renesas

Renesas RA Series Manuale utente

Renesas

Renesas RA Series Manuale utente

Renesas

Renesas YROTATE-IT-RX23T Manuale utente

Renesas

Renesas RL78/I1A Manuale utente

Renesas

Renesas RA6 Series Manuale utente

Renesas

Renesas RX100 Series Manuale utente

Renesas

Renesas SKP36912G Manuale utente

Renesas

Renesas M16C/64A Series Manuale utente

Renesas

Renesas RSKRL78G14 Guida rapida

Renesas

Renesas RL78/G13 Manuale di istruzioni

Renesas

Renesas RX62T Istruzioni per l'installazione e il funzionamento

Renesas

Renesas V850ES/Fx3 Series Manuale utente

Renesas

Renesas RX65N Series Manuale utente

Renesas

Renesas RX62T Manuale utente

Renesas

Renesas 78K0R/KE3 Manuale utente

Renesas

Renesas RX100 Series Manuale utente

Renesas

Renesas RL78/I1A Manuale utente

Renesas

Renesas RA6M5 Manuale utente

Renesas

Renesas E100 Manuale utente

Renesas

Renesas V850ES/F 3-L Series Manuale utente

Renesas

Renesas RL78 Series Manuale utente

Renesas

Renesas HD6473937RXV Manuale utente

Renesas

Renesas RX220 Series Manuale utente

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente