Repotec RP-G2602D Manuale utente
24-P + 2-SFP Gigabit Ethernet Switch
User Manual
V1.0
FCC Certifications
This Equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference received;
including interference that may cause undesired
operation.
CE Mark Warning
This equipment complies with the requirements
relating to the EMC Directive 2004/108/EC, the Low
Voltage Directive 2006/95/EC, and the RoHS
Directive 2011/65/EU.
Company has an on-going policy of upgrading its
products and it may be possible that information in
this document is not up-to-date. Please check with
your local distributors for the latest information. No
part of this document can be copied or reproduced in
any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of
their respective companies.
Copyright © 2014, All Rights Reserved.
Unpacking Information
Thank you for purchasing this product.
Before installation, please verify that your
package contains the following items.
1. One 24-Port Gigabit Ethernet switch
with 2 SFP ports
2. One AC power cord
3. Rack-mount bracket x2
4. Rubber foot x4 and screws
5. One user manual
Introduction
Easily boost your networking throughput,
the rack-mountable switch provides you 24
10/100/1000Mbps ports that lead you to a
real Gigabit connection. Users are now able
to transfer large and high
bandwidth-needed files faster and hence
get a real efficiency improvement. In
addition to the cooper ports, 2 ports
support fiber connection with the 2
equipped Mini-GBIC ports for obtaining
long-distance communication.
The switch offers users with fast and
reliable network. The store-and-forward
architecture filters errors and forwards
packets in a non-blocking environment.
Flow control ensures the correctness of
data transmitting. The 802.3x and
backpressure flow control mechanisms
work respectively for full and half duplex
modes.
2
The switch features with easy installation
and maintenance. It supports N-Way
auto-negotiation protocol, which detects
the networking speed (either 10/100/1000
Mbps) and the duplex modes (Full or Half
duplex mode) automatically and do an
immediately adjustment to advance the
capability and performance.
Auto-MDI/MDI-X function alleviates the
effort to use crossover cables. Users need
not to prepare crossover cables for
equipment connectivity. Also, rich
diagnostic LEDs are provided for users to
get real-time information of the connection
status that helps to do quick response and
correction.
Key Feature
Complies with 10BASE-T specifications
of the IEEE802.3 standard
Complies with 100BASE-TX
specifications of the IEEE802.3u
standard
Complies with 1000BASE-T
specifications of the IEEE802.3ab
standard
Complies with 1000BASE-X
specifications of the IEEE802.3z
standard
Complies with IEEE802.3az Energy
Efficient Ethernet
Complies with IEEE 802.1p Cos
3
Supports back-pressure (half duplex)
and flow control (IEEE 802.3x)
Supports N-Way protocol for speed
(10/100/1000Mbps) and duplex mode
(Half/Full) auto-detection
Supports MDI/MDI-X auto crossover
and polarity correction
Store-and-forward architecture filters
fragment & CRC error packets
Push on/off button to enable/disable
IEEE802.3az
Provides 2 SFP ports for optional fiber
connection
Supports 8K entries MAC address
Support 4.1M bit buffer memory
Support 10K bytes jumbo frames
Supports extensive LED indicators for
network diagnostics
Rack mountable
Internal power supply
100~240V AC/50~60Hz universal input
EMC: FCC, CE Class A
Safety: LVD EN60950-1
4
Front Panel
The front panel of the switch contains the
RJ45 ports, LEDs, 2 SFP ports and an
IEEE802.3az EEE ON/OFF button. For
detailed LED definition, please refer to the
next paragraph.
The front panel of the switch is shown as
below:
LEDs Definition
This switch contains one power LED and
Link/Act LEDs that shows the activities and
information of the ports.
LED Status Operation
Power
Steady Green The switch is powered on
Off The switch is powered off
Link/
ACT
Steady Green Valid port connection
Blinking Green
Valid port connection and
there is data transmitting/
receiving
Off Port disconnected
5
RJ-45 Ports
All the RJ-45 ports in the device are
auto-negotiating and auto-crossover. An
auto-negotiating port can detect and adjust
to the optimum Ethernet speed
(10/100/1000 Mbps) and duplex mode (full
duplex or half duplex) of the connected
device. An auto-crossover (auto-MDI/MDI-X)
port automatically works with a
straight-through or crossover Ethernet
cable.
Mini-GBIC Slots
There are two slots for mini-GBIC (Gigabit
Interface Converter) transceivers. You can
plug the SFP port modules into the switch.
The SPF port modules are to be used with
fiber-optical transceiver cabling in order to
uplink various other networking devices for
a gigabit link that may span great
distances.
You can change transceivers while the
switch is operating and use different
transceivers to connect to Ethernet
switches with different types of fiber-optic
or even copper cable connectors.
The SFP modules is a hot-pluggable
transceiver and specified by a multi-source
agreement (MSA). See the SFF committee’s
INF-8074i specification Rev 1.0 for details.
6
802.3az ON/OFF button:
The IEEE802.3az ON/OFF button helps
reducing the power consumption of switch.
This button allows users to keep the best
performance without transmission impacted
or to have the green support of Energy
Efficient Ethernet mode with the simple
push of a button.
Rear Panel
The three-pronged power receptacle is
located on the rear panel of the switch.
The rear panel of the switch is shown as
below.
Power Receptacle
To be compatible with the electric service
standards around the world, the switch is
designed to afford the power supply in the
range from 100 to 240VAC, 50/60Hz.
Please make sure that your outlet standard
to be within this range.
To power on the switch, connect one end of
the supplied power cord to the power
receptacle on the back of the switch and
the other end to the appropriate power
source. After the power cord installation,
please check if the power LED is illuminated
for a normal power status.
7
Installation
This switch can be placed on your desktop
directly, or mounted in a rack. The
installation is a snap. Users can use all the
features of the switch with simply attaching
the cables and turning the power on.
Before installing the switch, we strongly
recommend:
1. The switch is placed with appropriate
ventilation environment. A minimum
25mm space around the unit is
recommended.
2. The switch and the relevant
components are away from sources of
electrical noise such as radios,
transmitters and broadband amplifiers.
3. The switch is away from environments
beyond recommend moisture.
Desktop Installation
1. Attach the provided rubber feet to the
bottom of the switch to keep the switch
from slipping. The recommend position
has been square-marked.
2. Install the switch on a level surface that
can support the weight of the unit and
the relevant components.
3. Plug the switch with the female end of
the provided power cord and plug the
male end to the power outlet.
8
Rack-mount Installation
The switch may standalone, or may be
mounted in a standard 19” rack. Rack
mounting produces an orderly installation
when you have a number of related
network devices. The switch is supplied
with two optional rack mounting brackets
and screws, which are used for rack
mounting the unit.
Rack-mount Installation Requirements:
1. Two mounting brackets.
2. Six M3 flat head screws
Procedures to Rack-Mount the switch in the
rack:
1. First disconnect all the cables from the
switch.
2. Place the unit the right way up on a
hard, flat surface with the front facing
you.
3. Locate a mounting bracket over the
mounting holes on one side of the unit.
4. Insert the screws and fully tighten with
a suitable screwdriver.
5. Repeat the two previous steps for the
other side of the unit.
6. Insert the unit into the rack with
suitable screws.
7. Reconnect all the cables.
Altri manuali per RP-G2602D
1
Indice
Altri manuali Repotec Router di rete
Repotec
Repotec RP-1708K Manuale utente
Repotec
Repotec Powerline 85M Manuale utente
Repotec
Repotec RP-170508K Manuale utente
Repotec
Repotec WA 2614 Manuale utente
Repotec
Repotec RP-PE054 Manuale utente
Repotec
Repotec WD-5714 H Manuale utente
Repotec
Repotec RP-S48G4 Manuale utente
Repotec
Repotec ADSL2+ Powerline Router Manuale utente
Repotec
Repotec RP-G3224DB Manuale utente
Repotec
Repotec Powerline 85M Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza