RIGHT ANGLE NewCrank 3.5 Series Manuale utente

DETAIL A

6703 ZINSER ST., SCHOFIELD, WI 54476

PHONE: 800.298.4351 FAX: 866.882.9475

.raproducts.com

K&A MANUFACTURING

STEPS 1-4

WORKSURFACE

SUPPORT

PAGE 1 OF 3

VERSION DATED: 8/20/14

TOOLS REQUIRED FOR ASSEMBLY:

POWER DRIVER W/ADJUSTABLE

TORQUE

#2 PHILLIPS HEAD DRIVER BIT

#2 SQUARE HEAD DRIVER BIT

SMALL PHILLIPS SCREWDRIVER

3/16 HEX HEAD DRIVER BIT OR

ALLEN WRENCH

TAPE MEASURE

LEVEL

NewCr nk SERIES 3.5 HEIGHT ADJUSTABLE WORKSTATION ASSEMBLY

INSTRUCTIONS:

STEP 1: LAY THE WORKSURFACE 1 ON A PROTECTED SURFACE WITH THE

PILOT HOLES FACING UP. ALIGN THE HOLES IN THE WORKSURFACE SUPPORT

ON THE LEG ASSEMBLY WITH THE PILOT HOLES IN THE WORKSURFACE. NOTE

THAT THE CRANK CAN BE INSTALLED ON EITHER LEG ASSEMBLY.

STEP 2: PLACE A CLAMP 4 ON THE CRANK HANDLE ASSEMBLY 3 . SLIDE THE

HANDLE ASSEMBLY INTO THE CRANK BRACKET 5 . PLACE THE OTHER CLAMP

ONTO THE HANDLE ASSEMBLY ON THE OPPOSITE SIDE OF THE CRANK HOLDER

FROM THE FIRST CLAMP. DO NOT TIGHTEN THE SCREWS IN THE CLAMPS.

STEP 3: INSERT THE HANDLE/CLAMP/BRACKET ASSEMBLY INTO THE HEX DRIVE

NEAR THE TOP OF THE LEG ASSEMBLY 2 UNTIL IT BOTTOMS OUT. YOU MAY NEED

TO TURN THE CRANK HANDLE ASSEMBLY SLIGHTLY TO ALIGN IT WITH THE HEX

DRIVE. ATTACH THE CRANK BRACKET 5 TO THE WORKSURFACE 1 WITH (4)

WOOD SCREWS 12 . DO NOT USE ANY PILOT HOLES. DO NOT OVERTIGHTEN

THE SCREWS. USE A LOW TORQUE SETTING ON THE DRIVER. THE WORKSURFACE

MATERIAL COULD STRIP.

STEP 4: SLIDE THE FORWARD CLAMP 4 AGAINST THE CRANK BRACKET 5 AND

TIGHTEN THE CLAMP SCREW. USE A SMALL PHILLIPS SCREWDRIVER. DO NOT

OVER-TIGHTEN THE SCREW. IT COULD STRIP. SLIDE THE CRANK HANDLE ASSEMBLY

OUT OF THE CLAMP BRACKET UNTIL IT JUST CLEARS THE FRONT OF THE WORK-

SURFACE. SLIDE THE BACK CLAMP AGAINST THE BACK OF THE CRANK BRACKET

AND TIGHTEN THE CLAMP SCREW.

INSTRUCTION # 53238 HARDWARE PACK # 53222 OR 53239

ITEM # PART # DESCRIPTION QTY

1 VARIES Series 3.5 Worksurface 1

2 VARIES NewCrank Series 3.5 Left Leg Assembly 1

3 VARIES NewCrank Series 3.5 Crank Handle Assembly 1

4 53141 NewCrank Clamp W/Screw 1

5 801315 Ketterer Crank Bracket 1

6 VARIES NewCrank Series 3.5 Hex Rod 1

7 VARIES NewCrank Series 3.5 Right Leg Assembly 1

8 VARIES Series 4 Cross Support 1

9 53025 5/16 Lock Washer 4

10 53024 5/16-18 x 1/2 Button Head Socket Screw 4

11 800934 Cross Support End Cap 2

12 51708 M5 x 18mm (7/8 ) Sq/Ph/Wshr Head Wood Screw 28

13 VARIES Series 4 LT 48 U-Channel 1

LEVELING GLIDE

STEPS 6-10

PRE-INSTALLED

WELD NUTS

STEP 8: INSERT (2) END CAPS 11 INTO THE ENDS OF THE CROSS SUPPORT 8 .

STEP 9: ATTACH THE LEG ASSEMBLIES 2 AND 7 TO THE WORKSURFACE 1 USING (16) WOOD SCREWS 12 .

DO NOT OVER-TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING ON THE DRIVER.

STEP 10: CENTER THE U-CHANNEL 13 ON THE HEX ROD 7 AND BETWEEN THE LEG ASSEMBLIES 2 AND 7 .

DO NOT USE ANY PILOT HOLES. ATTACH THE U-CHANNEL WITH (8-12 ) WOOD SCREWS 12 .

STEP 11: WITH THE HELP OF AN ASSISTANT, SET THE WORKSTATION UPRIGHT IN ITS FINAL LOCATION. LEVEL THE

WORKSTATION IF REQUIRED BY TURNING THE LEVELING GLIDES CLOCKWISE (FROM THE TOP) ON THE LOW

CORNERS OF THE UNIT. IF YOUR WORKSTATION HAS CASTERS, LEVEL IT BY TURNING THE BOLTS ON THE TOP OF

THE CASTERS. THE WORKSTATION IS NOW READY FOR USE.

4.000

6703 ZINSER ST., SCHOFIELD, WI 54476

PHONE: 800.298.4351 FAX: 866.882.9475

.raproducts.com

K&A MANUFACTURING

STEP 5

PAGE 2 OF 3

DETAIL B

STEP 5: INSERT THE HEX ROD 6 INTO THE HEX DRIVE NEAR THE TOP OF THE LEG ASSEMBLY WITH THE CRANK

ASSEMBLY ATTACHED. PLACE THE OTHER LEG ASSEMBLY ON THE WORKSURFACE INSERTING THE OTHER END OF

THE HEX ROD INTO THE HEX DRIVE.

STEP 6: WITH THE HELP OF AN ASSISTANT, PLACE (4) WASHERS 9 ON (4) SOCKET SCREWS 10 . INSERT THESE

THROUGH THE HOLES AT THE ENDS OF THE CROSS SUPPORT 9 AND THREAD THEM INTO THE WELD NUTS PRE-

INSTALLED IN THE LEG ASSEMBLIES. SEE DETAIL B. DO NOT FULLY TIGHTEN.

STEP 7: LEVEL THE CROSS SUPPORT 8 AT 4 FROM THE BOTTOM OF THE WORKSURFACE SUPPORT. SEE

DETAIL C. FULLY TIGHTEN THE SOCKET SCREWS 10

DETAIL C

PAGE 3 OF 3

TROUBLESHOOTING: IF YOU ARE HAVING ANY PROBLEMS WITH THE TABLE

OPERATION, CONTACT RIGHTANGLE™ SERVICE AT 800-298-4351 OR

[email protected]

WARRANTY INFORATION: NewHeights™ PRODUCTS ARE WARRANTED TO BE

FREE OF DEFECTS DUE TO MANUFACTURING OR MATERIALS AS FOLLOWS:

2 YEARS ON THE GEARS. 5 YEARS ON THE SUPPORT BRACKETS, ALUMINUM

COLUMNS AND FEET. WE WILL REPLACE ANY DEFECTIVE PART AFTER INSPECTION

BY AN AUTHORIZED AGENT. COSTS INCURRED DUE TO PRODUCT REPLACEMENT

SUCH AS INSTALLATION LABOR OR TRANSPORTATION ARE NOT COVERED UNDER

THIS WARRANTY.

6703 ZINSER ST., SCHOFIELD, WI 54476

PHONE: 800.298.4351 FAX: 866.882.9475

.raproducts.com

K&A MANUFACTURING

Altri manuali RIGHT ANGLE Scrivania

RIGHT ANGLE

RIGHT ANGLE NewFixed HEIGHT WORKSTATION Manuale utente

RIGHT ANGLE

RIGHT ANGLE R-STYLE PLAN 110 Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewCrank SPLIT WORKSURFACE CRANK HEIGHT ADJUSTABLE... Manuale utente

RIGHT ANGLE

RIGHT ANGLE R-STYLE PLAN 1 WORKSTATION Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights 4 NZP Series Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights 4 NFD Series Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights Series Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights ELECTRIC HEIGHT ADJUSTABLE... Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights 4 Series Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights SPLIT WORKSURFACE ELECTRIC HEIGHT ADJUSTABLE... Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights RECTANGULAR 3-LEG WORKSTATION Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewCrank 3-LEG CRANK HEIGHT ADJUSTABLE... Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights Elegante XT Series Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights 4 Bonita ET Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights Series Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewHeights 4 FD Series Manuale utente

RIGHT ANGLE

RIGHT ANGLE NewFixed 3-LEG WORKSTATION Manuale utente

Manuali Scrivania popolari di altre marche

HP m9060n - Pavilion - Elite Scheda tecnica

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

HP Presario SV7000 - Desktop PC Manuale utente

HP ProDesk 400 G5 Manuale

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente