ring Door View Cam Manuale utente
Door View Cam
Model: G63R9A
Charge the provided battery.
= Charged
= Charging
Grab your Wi-Fi password.
You’ll need it later to set up your Door View Cam.
Write it down below so it’s handy when you need it:
Clean up any paint.
If your peephole was painted over, you may have to remove the excess in
order to unscrew it (if not, skip ahead).
Check for paint on or around your peephole, both indoors and outdoors.
Use the toothed edge of the Door View Key to carefully remove paint
covering the edges or slots.
Download the Ring app.
The Ring app walks you through setting up
and managing your Door View Cam.
Search for “Ring” in one of these app stores,
or visit: ring.com/app.
First, fully charge the battery.
Find it in the Door View Kit tray,
along with the adapter and
tightening nut.
Plug it into a USB power source
using the provided orange cable
(located underneath your
Door View Key).
The battery is fully charged
when just one LED is lit.
Download from
Windows Store
Download from
Windows Store
Indoor Side Outdoor Side
32
Remove the indoor half.
On the indoor side, place the flat
edge of the Door View Key into the
slots on your peephole and rotate
counter-clockwise to unscrew it.
Once it’s loose enough, you can use
your fingers to finish unscrewing it
and remove it completely.
You may have to secure the outdoor side
of the peephole while unscrewing the
indoor portion to keep it from spinning.
Remove the outdoor half.
With the indoor side removed,
the outdoor portion should
slide right out.
In the event that it doesn’t,
check again for paint or other
obstructions around the lens.
If this isn’t your forever home,
consider storing the peephole
in a safe place in case you have
to re-install it one day.
54
Smooth the edges.
If the hole in your door is smooth, skip ahead.
If there are sharp or jagged edges, use the Door View Key to smooth
the opening.
Check the edges of the hole.
After you’ve removed your peephole, inspect both sides of the hole
(indoors and outdoors) for sharp or jagged edges.
76
Place the outdoor assembly.
From the front side of your door, insert
the tube through the hole until your
Door View Cam is flush with the door.
Now head inside...
Remove the orange cap.
On the indoor side, remove and
discard the protective orange cap
from the end of the tube.
We’ll continue setup
from this side of
your door.
98
Remove the rear cover.
Grasp the thin edge of the indoor assembly body, and pinch the cover
at the indentations.
Pull the body and cover apart. Set the cover aside for now.
You might need the included adapter.
It’s used to support larger door view holes. Let’s find out if it’ll fit yours...
Remove the adapter from the Door View Kit tray. From the indoor side
of your door, place the adapter over the tube and cable, then slide it
towards the hole.
If it DOES NOT slide in easily,
don’t force it through.
You won’t need the adapter.
If it DOES slide in easily,
insert the adapter until the
rim is flush with your door.
You may have to hold the outdoor
assembly in place while inserting the
adapter to keep it from falling out;
if you’ve got a wide door, grab a partner.
1110
Place the indoor assembly.
Next, carefully slide the indoor assembly
onto the tube until it’s flush with your
door, making sure the outdoor assembly
isn’t pushed out the other side.
Pull out the connector cable.
Once again, you may have to hold the
outdoor assembly in place to keep it from
falling out while placing the indoor assembly.
Join the indoor and outdoor assemblies.
While holding the cable out of the way, place the tightening nut from
the Door View Kit tray onto the tube (DO NOT attempt to thread the
cable through the nut).
Using either your fingers or the Door View Key, twist clockwise and
tighten firmly to make sure your Door View Cam doesn’t rotate freely.
Once secure, check the outdoor assembly. It may shift slightly while
tightening, so make sure it’s level.
Grasp either side of the exposed gray connector, and delicately draw it
out of the tube until there’s no more slack left.
We tucked it into the tube for safe travels,
but now it’s time to take it out.
OR
1312
Plug in the connector.
Gently pull the cable taut, then
firmly press the connector into
the port on the indoor assembly,
ensuring it is inserted.
Secure the cable.
Press the tab with the arrow into the
channel and secure the remaining
slack in the cable.
Insert the battery.
Slide the charged battery into the bottom of
your Door View Cam until it clicks into place
(don’t put the cover back on just yet).
Complete setup in the Ring app.
In the Ring app, select Set Up a Device and
follow the in-app instructions.
Once setup is complete, place the cover back
on your Door View Cam.
15
© 2019 Ring LLC or its aliates.
Ring and all related logos are trademarks of Ring LLC or its aliates.
For a list of all our customer support numbers, visit: ring.com/callus
For additional help, visit: ring.com/help
Or give us a call…
AU 1 300 205 983
NZ +64 9 887 9871
HK +852 5808 9388
SG 001 800 8700 9781
MY +60 1-800-81-8772
Worldwide +1 310 929 7085
Altri manuali per Door View Cam
1
Indice
Altri manuali ring Accessori
ring
ring Motion Sensor Manuale utente
ring
ring Contact Sensor 2nd Generation Z-Wave Manuale utente
ring
ring Contact Sensor Manuale utente
ring
ring 5AT3T5 Manuale utente
ring
ring Stick Up Cam Istruzioni operative e di sicurezza
ring
ring 5B28S5 Manuale dell'operatore
ring
ring Doorbell Pro Manuale utente
ring
ring Doorbell Pro 2 Manuale utente
ring
ring Peephole Cam Manuale utente
ring
ring Contact Sensor Manuale utente
ring
ring BHAGC001 Manuale utente
ring
ring Video Doorbell 4 Manuale utente
ring
ring 5F52E9 Manuale dell'operatore
ring
ring VIDEO DOORBELL Manuale utente
ring
ring Doorbell Pro Manuale utente
ring
ring Z-Wave Manuale utente
ring
ring Video Doorbell 3 Manuale utente
ring
ring Protect Kit Manuale utente
ring
ring BHALP021 Manuale utente
ring
ring Doorbell Pro Istruzioni operative e di sicurezza
