RIOTEC LS6300E Manuale utente
Laser Barcode
Scanner
Model no.
LS6300E/LS6320E
User’s Manual
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user‘s authority to operate the equipment.
Limited Warranty
No warranty of any kind is made in regard to this material, including, but not limited to,
implied warranties of merchantability or fitness for any particular purpose. We are not liable
for any errors contained herein or for incidental or consequential damages in connection with
furnishing, performance or use of this material. We shall be under no liability in respect of
any defect arising from fair wear and tear, willful damage, negligence, abnormal working
conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of
the products without written approval.
1
Table of Contents
1. INTRODUCTION……………………………………………………………………………… ..…2~3
2. INSTALLATION………………………………………………………………………………..…...4~6
3. SET UP FROM BAR CODE LABEL………………………………………………………….……..7
Multi-interface Functions……….………………………………………………………..8~9
Interface-KBW………………………………………………………………………………….10
Interface-Serial……..……………………………………………………………………11~12
Symbologies On/Off…………………………………………………………………….13~15
Symbologies Set Up…………………………………………………………………….16~21
Edit Setup Bar Codes……………………………………….……………….………..…… 22
Macro/Special Keys Setup Bar Codes………………………………………………….23
Termination String Setup Bar Codes…………………………………………………..24
4. FACTORY DEFAULT SETTING…………..……………………….………………..………25~26
5. APPENDIX A: TROUBLESHOOTING AND ERROR BEEPS……..………………….27~31
2
Introduction
3
RIOTEC 1D Laser barcode scanner combines the best scanning performance and value. The
device provides an accurate, easy, and fast method of data entry and data storage for
computerized information systems. It is easy to install and does not require Software or
drivers to operate.
RIOTEC laser barcode scanner can compatible several interfaces (USB, K/B, RS-232,) and
numerous configurations, is a powerful and reliable handheld scanner without compromise.
All the operating parameters are programmed by bar code programming menu and stored in
non-volatile RAM which can retain the settings after power is turned off.
When a barcode is successful decoded, the blue LED light of the scanner will turn on and off.
The scanner will beep once. If the barcode is not successful read, the LED will show red and
the buzzer will not sound.
LED
Exit Window
Trigger
Handle
BUZZER
4
Installation
Insert the plug on the free end of the Communications Cable into the appropriate connector on
the t as below described:
1. USB cable Connection:
Reset Configuration to Defaults
If you are unsure of the scanner configuration or have scanned the incorrect codes,
please scan the “Reset Configuration to Defaults” barcode. This will reset the scanner
to its factory defaults settings in USB interface.
2. PS2 (K/B) cable Connection:
Reset Configuration to Defaults
If you are unsure of the scanner configuration or have scanned the incorrect codes,
please scan the “Reset Configuration to Defaults” barcode. This will reset the scanner to
its factory defaults settings in PS/2 interface.
Connect with host
Connect with host
Connect with keyboard’s
connector
5
3. RS232 cable Connection:
NOTE: for Serial port (RS232 cable), please plug the power connector of 5V power
adapter to RS232 cable.
Reset Configuration to Defaults
If you are unsure of the scanner configuration or have scanned the incorrect codes,
please scan the “Reset Configuration to Defaults” barcode. This will reset the scanner to
its factory defaults settings. Then “000601” for RS232 serial setting.
4. Auto-sensing setup
For some scanners have auto-sensing function. There is an auto-sensing function button
shown on below photo. Default is ON.
*Auto-sensing normally is ON. Press once is OFF, Press once again is ON.
Connect with host
Require adapter for power supply
6
Operation
1. Be sure that Host computer is turned OFF.
2. Ensure that all connections are secure.
3. Turn on your host. And please operate the scanner under the right software
application, such as Notepad or Word(RS232 interface should be under
Hyper Terminal” and make the right setting).
4. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default),
and press the trigger.
5. On successful decode, the blue LED light will turn on and off. The scanner will
beep once.
Tip
Do not hold the scanner directly over a barcode at 90˚. Scanning light bounces directly
back into the scanner from the barcode label is known as specular reflection which will
create a "dead zone" where decoding is difficult. Practice a few times to find what range
of angles works best.
Maintenance
Cleaning the scan window is the only maintenance required. A dirty window may
affect scanning accuracy.
Wipe the scanner window gently with a lens tissue or other material suitable for cleaning
optical material.
Do not spray water or other cleaning liquids directly onto the window.
7
Setup from Bar Code Label
8
Multi-Interface Functions – 1
OUTPUT FIRMWARE VERSION
RESET CONFIGURATION TO
DEFAULTS
0A 0B
OUTPUT MODE – KEYBOARD / USB OUTPUT
MODE
OUTPUT MODE - SERIAL
000600 000601
GOOD READ BEEP TONE – NONE BUZZER /
LED
GOOD READ BEEP TONE - RESET
014200 0B142
DECODE OPTIONS REVERSE IMAGE –
ENABLE
IMAGE
DECODE OPTIONS REVERSE IMANGE
- DISABLE
01391 01390
DECODE OPTIONS SEND BAR CODE ID -
DISABLE
CODE ID
DECODE OPTIONS SEND BAR CODE
ID – AS A PREFIX
01400 01401
DECODE OPTIONS SEND BAR CODE ID -
RESET
DECODE OPTIONS SEND BAR CODE
ID – AS A SUFFIX
Altri manuali per LS6300E
2
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali RIOTEC Lettore di codici a barre
RIOTEC
RIOTEC iLS6303XBU Manuale utente
RIOTEC
RIOTEC CR6300C Manuale utente
RIOTEC
RIOTEC LS6300F Manuale utente
RIOTEC
RIOTEC iDC9507A Manuale utente
RIOTEC
RIOTEC iDC9602N Manuale utente
RIOTEC
RIOTEC iLS6302ABU Manuale utente
RIOTEC
RIOTEC iLS6300DBU Manuale utente
RIOTEC
RIOTEC DC9250 Manuale utente
RIOTEC
RIOTEC RIOSCAN iCR6307AS Manuale utente
RIOTEC
RIOTEC iDC9272A Manuale utente
RIOTEC
RIOTEC iLS6300VBQ Manuale utente
RIOTEC
RIOTEC iDC9273A Manuale utente
RIOTEC
RIOTEC iLS6300DBQ Manuale utente
RIOTEC
RIOTEC LS6302A Manuale utente
RIOTEC
RIOTEC CR6327A Manuale utente
RIOTEC
RIOTEC DC9257A Manuale utente
RIOTEC
RIOTEC LS6007 Manuale utente
RIOTEC
RIOTEC DC9253AP Manuale utente
RIOTEC
RIOTEC iDC9600KW Manuale utente
RIOTEC
RIOTEC DC9250DP Manuale utente
Manuali Lettore di codici a barre popolari di altre marche
POSMicro
POSMicro Datalogic PowerScan D7100 Manuale utente
Marson
Marson MT780 Guida rapida alla configurazione
NCR
NCR RealPOS Manuale utente
Motorola
Motorola SE3300 Guida rapida alla configurazione
Element
Element P130BT Manuale utente
Motorola
Motorola Symbol LS3008 Manuale di installazione e funzionamento
