Risco Gardtec GT480 Manuale utente
GG
GGTT
TT44
4488
8800
00
CC
CCoo
oonn
nntt
ttrr
rroo
ooll
ll
PP
PPaa
aann
nnee
eell
ll
User Instructions
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 1
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Display Status Blanking . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT USER INFORMATION . . . . . . . . . . . . . . 2
Full Setting the System . . . . . . . . . . . . . . . . . . . . . . . . 3
Setting & Unsetting the System via a Keyswitch . . . . . . 3
Pre Exit Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Part Setting the System (using Part 1) . . . . . . . . . . . . . 4
Part Setting the System (using Part 2 or 3) . . . . . . . . . . 5
Unsetting the System . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Display After Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Resetting After Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Tamper Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the System with Mains Fail . . . . . . . . . . . . . . . . 10
Programming User Codes . . . . . . . . . . . . . . . . . . . . . . 12
Programmable User Options . . . . . . . . . . . . . . . . . . . . 15
Zone Remove Option . . . . . . . . . . . . . . . . . . . . . . . . . . 15
System Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Turning Chime On/Off . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting Time & Date . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Reading the Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Keypad Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Keypad Tamper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tamper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
System Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 1
Introduction
Welcome to the GT480 control panel. Your installation company will
have programmed your system to protect your premises to the highest
possible standards. Several user programmable options are available
that will be covered later in this manual. Throughout this manual
reference will be made to the Master User Code. The factory set
default is 5678. This code is programmable along with eight other User
Codes.
If an Engineer is on site, it may be necessary to authorise them to
access your system. Do this by entering your User Code when
asked to do so by the engineer.
One of two types of Keypad may be fitted to your system, the first type
has Text on the keys for example Yes and No Keys. The second type
uses Icons and is designed to be multi-lingual (see table below).
PP
PPaa
aagg
ggee
ee
11
11
Icon style keypad Text style keypad
Full
Part
Quick
Yes
No
! ! ! IMPORTANT ! ! !
The Keypad may have ‘Icon’ style keys
instead of ‘Text’ style keys. Please use
the table above for a conversion of the
different styles. This will be reflected in
this manual, for example.
Press Yes ( )
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 1
PP
PPaa
aagg
ggee
ee
22
22
Display Status Blanking
Depending on Control Panel installed, it may be a requirement that
the Status (Set or Unset display) of the security system is not
displayed. Set or Unset Status will only be displayed for ten seconds
when the system is Set or Unset. The bottom line of the display will
then be blanked off.
I
If the Control Panel is non EN then all displays will be shown and
“CHECK” will not be displayed.
All information displays will remain until cleared by the User.
IMPORTANT USER INFORMATION
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 2
PP
PPaa
aagg
ggee
ee
33
33
Full Setting the System.
After checking the premises are secure:
1) Enter a valid User Code followed by Yes ( ).
2) The exit tone will now sound.
3) Exit the premises via an authorised exit route.
4) Once the premises are secure, listen (from outside the
protected area) for the exit tone to finish.
Note: To abort the exit, enter a valid User Code.
Setting & Unsetting the System via a Keyswitch (if fitted).
Biased Keyswitch
To set the system with a biased keyswitch, insert the key and turn it,
then return the key to the original position and remove. Follow the
instructions from step 3 (above).To unset, repeat this operation.
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 3
PP
PPaa
aagg
ggee
ee
44
44
Pre Exit Check.
At the start of the setting procedure, a fault
tone will sound if any non exit routes are
open. The display will show, for example:-
If the fault clears within 20 seconds then the exit tone will begin, if not,
the fault tone will continue until a valid User code is entered.
Part Setting the System (using Part 1).
Up to three Part Sets may be available for your system. Please refer to
the customer details at the rear of this manual for information about
Part Set zones. Part Set zones will be omitted from the system when
that particular Part Set is used. To set the system using Part 1.
1) Enter a valid User Code followed by 1 ().
2) Retire to an unprotected area.
Note: To abort the exit, enter a valid User Code.
Exit Now ! . . .
Zone 3
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 4
PP
PPaa
aagg
ggee
ee
55
55
Part Setting the System (using Part 2 or 3).
Two other Part Sets may be available for your system. Part 2 is a
second set of zones that may be omitted and Part 3 will combine Part
1 and Part 2. To use Part 2 or 3.
1) Enter a valid User Code followed by 2 or 3.
2) Retire to an unprotected area.
Note: To abort the exit enter a valid User Code.
3) The exit tone may or may not be heard depending on the
system settings programmed by the installation company.
4) Exit the premises or retire to an unprotected part of the
system. At the end of the exit time, either the exit sounder
will stop (if the exit tone has been audible) or a single beep
will be emitted (if the exit tone has been silent).
5) The system is now Part Set. You are free to move around the
zones that have been removed by the Part Set but other
zones on the system are active.
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 5
PP
PPaa
aagg
ggee
ee
66
66
Unsetting the System.
1) Enter the premises via an authorised Entry Point.
2) The entry tone will sound.
3) Proceed to the keypad and enter a valid User Code.
Display After an Alarm.
If an alarm occurs when the system is Set, the cause of the alarm will
be displayed for 10 seconds after you unset the system.
1) The display will show, for
example:-
2) Then, after 10 seconds the display
will show:-
3) To view the cause of the alarm again, enter your User code.
Then press 0.
! ! ! ALARM 4 ! ! !
Zone 4
!!!! CHECK ! ! ! ! !
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 6
PP
PPaa
aagg
ggee
ee
77
77
Resetting After an Alarm
After an alarm the system needs to be reset.
Your installation company will have programmed the reset modes for
your system so that it complies with your insurance company and to
legislation requirements.
Your installation company will have informed you as to the type of
reset that your system is set for.
Before attempting to reset your system, ensure that the system
is Un-set and the fault has been rectified.
1) If the system has been
programmed for Anycode reset;
2) With the display showing:-
Enter your User code.
Then press Yes ( ).
The exit tone will sound and the
display will show:-
3) Enter your User code again to abort the setting.
The system is now reset.
!!!! CHECK ! ! ! ! !
Exit Now ! . . .
Ok !
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 7
PP
PPaa
aagg
ggee
ee
88
88
If a Master Code Reset has been programmed by the engineer, a
higher level of code will be required.
If Alarm Reset has been programmed for Master, then the display will
show, for example, each time the User attempts to set
the system.
Use a Master code to reset the system.
1) With the display showing:-
Enter a valid Master code.
Then press Yes ( ).
2) The exit tone will sound and the
display will show:-
3) Enter your Master User code again to abort the setting.
The system is now reset.
If an Engineer Code Reset has been programmed, please call the
Installation Company.
If Alarm Reset has been programmed for Engineer, then the display
will show, for example, each time the User attempts to
set the system.
! ! ! ALARM 4 ! ! !
Zone 4
!!!! CHECK ! ! ! ! !
! ! ! ALARM 4 ! ! !
Zone 4
Exit Now ! . . .
Ok !
GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 8
Indice
Altri manuali Risco Pannello di controllo
Risco
Risco gt490x Manuale utente
Risco
Risco GT 600 Manuale utente
Risco
Risco GardTec 350+ Manuale utente
Risco
Risco RisControl Manuale utente
Risco
Risco GT Plus Manuale di istruzioni
Risco
Risco GT 600 Manuale di programmazione
Risco
Risco RisControl Manuale utente
Risco
Risco ProSYS 128 Manuale utente
Risco
Risco LightSYS Manuale di istruzioni
Risco
Risco GardTec 350+ Manuale utente
