RIVIAN PT00401761 Manuale utente
JUNE 2022
FLEET AC DISPENSER WITH 18 FT CABLE
Installation Guide
PRODUCT NUMBER PT00401761
© 2021-2022 Rivian Automotive, LLC. All rights reserved.
All information in this document and all Rivian software is
subject to copyright and other intellectual property rights of
Rivian Automotive, LLC, its affiliates, or its licensors. This
material may not be modified, reproduced, or copied, in whole
or in part, without the prior written permission of Rivian
Automotive, LLC, its affiliates, or its licensors. Unless indicated
otherwise, all trademarks are owned and registered by Rivian
Automotive, LLC, its affiliates, or its licensors in the United
States and/or other countries. Please visit
https://www.rivian.com/legal/brand for Rivian's trademarks and
service marks.
Software embedded or accessed by the vehicle may utilize
open source software. Please visit
https://www.rivian.com/legal/open-source for more
information.
Contents
Important Safety Instructions 4
SAVE THESE INSTRUCTIONS 4
Precautions 4
Safety Symbols on Hardware Labels 8
Introduction 9
Identify Parts 9
Tools and Equipment 10
Remove the Faceplate 11
Install the SIM Card 12
Install the Dispenser 12
On a Rivian Gantry 12
On a Rivian Pedestal 12
On a Wall 15
Set the Operating Current 23
Connect Conductors 24
Install the Faceplate 25
Wall Installation Only - Wrap and Dock the Cable 26
Complete the Installation 26
Light Bar States 27
Troubleshooting 28
Specifications 29
Supplemental Information for Electrical Service Wiring 31
240V Split-Phase System 31
208V Three-Phase Wye-Connected 32
240V Three-Phase Delta-Connected 33
FCC Interference Statement 34
RF Exposure Information 34
Industry Canada Statement 35
Radiation Exposure Statement 35
Déclaration d'exposition aux radiations 35
Customer Service 37
Important Safety Instructions
SAVE THESE INSTRUCTIONS
DANGER
Read all the instructions before installing the Rivian
FleetACDispenser. Follow the safety instructions and
warnings in this guide when installing the FleetACDispenser.
Failure to do so may result in fire, electrical shock, serious
injury, or death.
PRECAUTIONS
The following safety symbols are used in this document.
DANGER
Risk of electric shock
DANGER
Risk of personal injury
CAUTION
Risk of damage to equipment
Risk of Electrical Shock
DANGER
lImproper connection of the equipment grounding conductor
can result in a risk of electric shock. Check with a qualified
electrician or service person if you are in doubt as to whether
the product is properly grounded.
lDo not touch live electrical parts. Incorrect connections may
cause electric shock.
4
lNo user serviceable parts inside. Refer servicing to qualified
service personnel.
lDo not put fingers into the coupler.
lDo not use this equipment if the flexible power cord or cable
is frayed, has broken insulation, or any other signs of damage.
lDo not use this equipment if the enclosure or the coupler
is broken, cracked, open, or shows any other indication of
damage.
lDo not allow unsupervised children in the area during
installation of the FleetACDispenser.
lBefore connecting the FleetACDispenser to a power supply,
check that the power supply voltage and current rating
corresponds with the power supply details shown on the
product ratinglabel.
lUse appropriate protection when connecting to a main
switchboard.
lGround the FleetACDispenser through a permanent wiring
system using the equipment grounding conductor.
lTo reduce the risk of fire, connect only to a circuit provided
with no more than 60 amperes maximum branch circuit
over-current protection in accordance with the National
Electrical Code, ANSI/NFPA 70, and the Canadian Electrical
Code, Part I, C22.2.
lWhen a breaker smaller than 60 amperes is used, ensure
that the conductor sizes used comply with the minimum
sizes prescribed by national and local electrical codes and
standards.
5
Risk of Personal Injury
DANGER
lDisconnect the power supply before installing or repairing
the FleetACDispenser. Failure to do so may result in
physical injury or damage to the power supply system and
the FleetACDispenser.
lKeep any packing materials away from children. These
materials are a potential source of danger, and can cause
suffocation.
lOnly a licensed electrician should perform this installation in
accordance with the provisions of national electrical codes
and standards.
6
Risk of Damage to Equipment
CAUTION
lUse anti-static gloves, wrist bands connected to ground, and
insulated tools for installation and removal of the faceplate.
lDo not operate this equipment in temperatures outside its
operating range of -30°C to +50°C (-22°F to +122°F).
lStore this equipment in a clean dry location between -40°C
and +80°C (-40°F to +176°F).
lDo not use extender cables to increase the length of the
charging cable.
lIf this unit is installed outdoors, the components and fittings
must be rated for outdoor installation. The outlet must be
installed properly to maintain the proper NEMA rating of
the enclosure.
lAvoid direct hand contact with components on the
networkboard.
lFor storage/shipping of the front panel or network board, use
a bubble wrap bag with ESD (electrostatic discharge)
protection.
lRivian does not recommend using a GFCI breaker since the
FleetACDispenser has charging circuit interrupting device
(CCID20) protection. Using a GFCI breaker in the panel can
cause nuisance tripping. If local codes require a GFCI breaker
for plug-in installation, Rivian recommends a hardwire
installation.
7
SAFETY SYMBOLS ON HARDWARE LABELS
The following safety symbols may appear on labels located on hardware used
in this installation.
Risk of Electric Shock
Danger
Phase
Equipment Ground
Instruction Manual
ULLogo
8
Introduction
This document provides installation instructions for the FleetACDispenser
with 18 ft cable on a Rivianpedestal, gantry, or wall.
Identify Parts
1. FleetACDispenser
2. Mounting plate (wall
installationonly)
3. Four T20 anchor screws
(wallinstallation only)
4. Two 13 mm M4 Phillips screws
5. Micro SIM (3FF) card
6. T20 Security bit
9
Tools and Equipment
Required Optional (Wall Installation
Only)
#2 Phillips screwdriver Hole saw
Security T20 Torx screwdriver Stud finder
Flathead screwdriver, 7/32 in width Level
Adjustable torque screwdriver,
10in-lb to 40 in-lb
Multimeter
10
Indice
