rock space RSD0613 Manuale utente
User Manual
Please read this instructions closely and keep it properly.
Whole Home Mesh WiFi System
RSD0613(3-pack)
https: //rockspace. afterservice. vip
24hour Online
After-sales Service
Scan QR To Visit
10/100/1000Mbps
LAN ports
10/100/1000Mbps
WAN/LAN port
DC power jack
Reset
button
Power DC-IN
Mesh
Mesh x 3 Ethernet cable x 1
Power adapter x 3 Quick installation guide x 1
Get to know your device
Package contents
Download and install the
RS WiFi App
Ⅰ
RS WiFi
RS WiFi
RS WiFi
Connect the primary node
1. Power o your modem, and remove its battery (if any).
2. Use the included Ethernet cable to connect a LAN port
of your modem or the Ethernet jack to the (WAN/LAN)
port of any node. This node is your primary node.
4. Use the included power adapter to connect the primary
node to a power source. Its LED indicator lights solid
green. Wait about for 40 seconds. The system
completes startup when the LED indicator blinks green.
3. Reinstall the battery of your modem, and power it on.
* The rst node you set up functions as the primary node,
while the rest are referred to as the secondary nodes.
Ⅱ
Modem
Ethernet jack
Or
www.rockspace.hk
Set up the primary node for
internet access
1. Go to the WiFi network list on your mobile device;
select the SSID of the primary node, and enter its
password. The default SSID and password are
specied on the bottom label of any node.
Ⅲ
Model: RSD0613
Power: 12V 1.5A
FCC ID: V7TMESH12
IC: 9034A-MESH12
MAC:
SN:
AC2100 Tri-band Whole Home Mesh WiFi System
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Power DC-INWAN/LAN
LAN1 LAN2
Made in China
ⅣSetup the primary node on
RS WiFi APP
2. Run the RS WiFi App and follow the onscreen
instructions to set up the primary node. After the
primary node is connected to the internet, its LED
indicator lights solid green.
1.Run the RS WiFi app, click "Add device". The QR code
scanning page would show up here. Select "Add Manually"
on the left side below the scanning zone.
2. The app will automatically turn back to the WiFi network list and
nd out the SSID Name labeled on the bottom of the mesh node,
input the given default password and connect to the network.
3. After the mesh node will nally connect to the network, open
the RS WiFi app again. If the page showing up is the scaning one,
click the name of the network on the upper left side of the page
and return to the rst page of the app. You do not need to scan for
a second time.
4.
Follow the given instructions. The setup wizard appears. Tap "Setup".
5. The app automatically detects your internet connection type.
Enter information according to the internet connection type and
tap "Next". The mesh unit is connected to the Internet and the app
proceeds to the next step.If your Internet connection type is PPPoE.
Enter your PPPoE user name and password and tap "Next”.
If your internet connection type is dynamic IP, tap "Next".
If your internet connection type is static IP, enter your IP address and
other information your ISP provides, and tap "Next".
6. When the mesh unit and the app is connected successfully,
it says" Connected".
7. The instruction will guide you to the Wireless Setting page for
further customizing your personal WiFi Name and Password of the
mesh. Tap "OK" when you nish setting up the new one.
Note: If you change the wireless network nameand password and
tap "OK", your mobile phone will disconnect with the mesh Wi-Fi
network. You need to reconnect to the new wireless network you
congured.
8. When the indicator of the mesh unit turns solid green,
it is connected to the Internet.
1. Place each node:
− In an elevated, open position within the coverage area
of your existing RS WiFi network.
− Keep your nodes away from electronics with strong
interference, such as microwave oven, induction cooker,
and refrigerator.
VConnect the secondary nodes
to the Internet on RS APP
Done .
2. Use the other power adapters to connect the remaining
secondary nodes to separate power sources, and their LED
light solid green. Wait for about 40 seconds. The secondary
node is connecting to another node when its LED indicator
blinks green.
3. After the primary node has been congured, the app will explain
how to set up the other nodes. Tap "OK" to view the specic steps.
You can also select "Add rock space mesh" on the setting page and
follow the steps to nish settings.
4. Observe the LED indicators of the secondary nodes until their
LED indicators light one of the following colors:
5. If the LED Indicator of a node does not light solid green, relocate
it according to the location recommendations in V. part to get better
connection.
Solid green Good connection
Solid yellow Fair connec tion
Solid red Disconnected
To access the internet with:
− Wired devices: Connect wired devices to the LAN ports of
any node.
− Wireless devices: Connect wireless devices to the WiFi
network using the SSID and the WiFi password you set.
If you want to manage the network anytime, anywhere, tap
and use your account to login.
FAQ
A1: Run the RS WiFi App, tap Settings in the lower-right corner, tap Wireless
Settings, change your SSID and password, and tap Save.
Then, you need to reconnect your mobile devices using the new SSID and
password.
A2: Tap the node on the RS WiFi App, tap “…” in the upper-right corner, and
choose “Delete”.
Note: Removing operation restores the node to factory settings.
A4: With the nodes powered on, hold the Reset button of your primary node down
using a paper clip for about 6 seconds, release when the LED indicator blinks
fast. Your network is reset successfully when the LED indicator lights solid on
then blinks again. And all nodes are restored to factory settings
A3: Yes. Run the RS WiFi App, tap Settings in the lower-right corner, tap Add
Nova, and follow the on-screen instructions to add.
Q1: How can I change my SSID and password?
Q2: How can I remove node from my WiFi network?
Q4: How to restore my network to factory settings?
Q3: Can I add another new set of node to expand my network coverage?
A5:
If your 2.4 GHz WiFi-enabled device supports the WPS function, perform the
steps below:
Step 1 Run RS WiFi App, tap Settings, WPS, and the WPS button
corresponding to the node near your device.
Step 2 Within 2 minutes, enable the WPS function on your device.
If your 2.4 GHz WiFi-enabled device does NOT support WPS function, perform
the steps below:
Step 1 Connect your smart phone used for setup to the WiFi network.
Step 2 Run RS WiFi App, tap Settings, Smart Assistant, and Enable. Your
smart phone connects to the 2.4 GHz WiFi network.
Step 3 Use the smart phone to set up your 2.4 GHz WiFi-enabled device
guided by its App.
Q5: My 2.4 GHz WiFi-enabled devices, such as a home security camera, cannot
connect to my nova WiFi network. What should I do?
Indice
