Roland VS-640i Manuale operativo
1
Copyright © 2020 ROLAND DG CORPORATION
1. To ensure correct and safe usage with a full understanding of this function’s performance, please be sure to
read through this manual completely.
2. Unauthorized copying or transferal of this manual, in whole or in part, is prohibited.
3. The contents of this document and the specications of this product are subject to change without notice.
4. Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur
through use of this function, regardless of any failure to perform on the part of this function.
5. Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur with
respect to any article made using this function.
Self Maintenance Guide
Limit Position & Cut Down Position Initialize
Read this rst
This describes the procedure and important conditions for performing Limit Position & Cut
Down Position Initialize that must be met in order to enable maintenance of this machine.
2
About and Notices.
Used for instructions intended to alert the operator to the risk of death
or severe injury should the unit be used improperly.
Used for instructions intended to alert the operator to the risk of injury
or material damage should the unit be used improperly.
* material damage refers to damage or other adverse eects caused
with respect to the home and all its furnishings, as well to domestic
animals or pets.
The symbol alerts the user to items that must never be carried out (are
forbidden). The specic thing that must not be done is indicated by the design
contained within the circle.
The symbol at left means not to touch.
The symbol alerts the user to things that must be carried out. The specic
thing that must be done is indicated by the design contained within the circle. The
symbol at left means the power-cord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions or warnings. The specic
meaning of the symbol is determined by the design contained within the triangle.
The symbol at left means “danger of electrocution”.
In addition to the and symbols, the symbols shown below are also used.
: Tips and advise before the adjustment.
To Ensure Safe Work
3
About the Labels Affi xed to the Unit
These labels are affi xed to the body of this product.
The following gure describes the location.
Caution: Moving Print Heads
The print heads inside the cover move
at high speed and pose a hazard. Never
insert the hand or ngers into the gap.
Caution: Pinching Hazard
Be careful not to allow the ngers to
become pinched when loading media or
closing covers.
Caution: Moving Print Heads
The print heads inside the front cover
move at high speed and pose a hazard.
Never insert the hand or ngers into the
gap.
Flammable
Ink and discharged fl uid are fl ammable.
Keep away from open fl ame.
Ink Is Toxic
Ink and discharged fl uid are toxic.
Avoid contact with the body. Use only in
a well ventilated area.
Flammable
Ink and discharged fl uid are fl am-
mable.Keep away from open fl ame.
Caution: High Temperature
The platen and dryer become hot.
Exercise caution to avoid re or
burns.
Ink Is Toxic
Ink and discharged fl uid are toxic.
Avoid contact with the body. Use
only in a well ventilated area.
Caution: High Voltage
Cover removal may pose hazard
of shock or electrocution due to
high voltage.
4
Limit Position & Cut Down Position Initialize
This function may solve one of the following errors or problem by re-setting the Limit Position and Cut Down
Position.
- Service Call 0101, 0103, 0105, or 0106
- Scan Motor Error
- Separating knife doesn't go down when Sheet Cut Function is performed
Procedure
Turn on the Sub Power SW while pressing [ ], [ ] and
[ ] keys to enter the Limit Initialize mode.
1
2
Remove the Right Cover.
LIMIT INITIALIZE
MENU
+
3Gently move the Tool Carriage to right and connect the Tool Car-
riage and the Head Carriage.
Then keep moving the Head Carriage gently together with the
Tool Carriage and lock the Head Carriage.
Conrm that the Head Carriage is locked by pushing it lightly to
left and eliminate the looseness.
If the Head Carriage moves to left smoothly, the Head Carriage is
not locked. Please repeat the procedure again.
2
1
5
5
6
4Conrm that the head is capped properly, and press [ENTER] key.
The Tool Carriage will be separated from the Head Carriage and
the limit position initialize will start.
After initialize is completed, the message is displayed.
To be in the Cut Down condition, move the Tool Carriage with
your hand until it makes full contact with the Auto Cutter Frame.
Press [ENTER] key to perform the Cut Down Position Initialize.
After initialize is completed, the message is displayed.
DETECTING..
SETTING UP
CUTTER DOWN POS
SETTING UP
THE LIMIT
[ ]
DETECTING..
INITIALIZATION
COMPLETED
SETTING UP
CUTTER DOWN POS
[ ]
Auto Cutter Frame
Altri manuali per VS-640i
2
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Roland Stampante
Roland
Roland SJ-745EX Guida rapida
Roland
Roland Metaza MPX-90 Manuale utente
Roland
Roland FJ-400 Manuale utente
Roland
Roland AJ-1000 Manuale utente
Roland
Roland SJ-740 Manuale utente
Roland
Roland SOLJET PROIII XC-540 Manuale utente
Roland
Roland SJ-1045EX Manuale utente
Roland
Roland Metaza MPX-80 Manuale utente
Roland
Roland VS-640 Manuale utente
Roland
Roland CAMM JET CJ-70 Manuale utente
Roland
Roland VersaStudio BR-20 Manuale per l'uso e la cura
Roland
Roland VersaUV LEF2-200 Manuale utente
Roland
Roland Texart RT-640 Manuale utente
Roland
Roland VersaUV LEF2-300 Manuale operativo
Roland
Roland SJ-740 Manuale utente
Roland
Roland SOLJET PRO4 XF-640 Manuale utente
Roland
Roland Texart RT-640 Manuale utente
Roland
Roland SOLJET PROIII XC-540 Manuale utente
Roland
Roland VersaUV LEJ-640 Manuale operativo e di manutenzione
Roland
Roland ColorCAMM PNC-5000 Manuale utente
