Rona 38115086 Manuale utente
Model / Modèle : 38115086
10’x 12’ Solitudes gazebo
Operators’ Manual. 9
Abri-soleil Solitudes 10 x 12 pi
Guide de l'utilisateur. 9
GAZEBO ASSEMBLY INSTRUCTIONS
Our clear, easy-to-follow, step-by-step instructions will guide you through the
project from start to finish. The final product will be a quality piece that will give
you years of enjoyment.
All you will need is a screwdriver, a hammer and two ladders of at least 8 feet (2.5
m) high (not included).
DO NOT assemble this item alone for your safety. Two people are necessary for
smooth & safe installation.
Item identification: For ease of identification, all parts are labeled to correspond to
the Step number in which the part is used.
Have6ormorepeoplehelpingyouwhenassemblingor
movingtheproduct.
Description Part Quantity Image
Big panel 1 A1 2
Big panel 2 A2 2
Small panel 1 B1 2
Small panel 2 B2 2
Long beam 1 C1 2
Long beam 2 C2 2
Short beam D 2
Lower connector 1 E 4
Lower connector 2 F 6
Top frame G 1
Slanting beam H 4
Middle beam I 6
Long PC 1 J1 4
Long PC 2 J2 4
Short PC 1 J3 4
Short PC 2 J4 4
Middle PC J5 4
Small PC 1 K1 2
Small PC 2 K2 2
Left plate L1 4
Right plate L2 4
PartsList
Description Part Quantity Image
Middle plate L3 2
Long plate M1 2
Short plate M2 2
Left rail N1 4
Right rail N2 4
Middle rail N3 2
Center plate O1 6
Corner plate O2 8
Hook P 1
Small top connector Q 1
Cover R 1
Small slanting beam S 4
Long netting tube T 4
Short netting tube U 4
Mosquito net V 1
PartsList
Part Description Quantity Image
AAM6X35Bolt4PCS
BBM6Flat washer78PCS
CCM6X15 Bolt74PCS
ZM6Wrench2PCS
HardwarePack1
`
Fig.1: Secure the small panels (B1 and B2) to the big panels (A1 andA2) by using bolts (AA) and flat washers (BB).
Fig.2: Secure the lower connector 1 (E) to the corner of the panels by using bolts (CC) and flat washers (BB).
Fig.3: Insert the long beam 1 (C1) into the long beam 2 (C2), then secure the long beam 1 (C1) to the long beam 2 (C2)
by using bolts (CC) and flat washers (BB). Reserve one hole on the long beam2 (C2) to assemble the netting tube.
Fig.4: Secure the assembled long beam 1 to the big panels (A1 andA2) by using bolts (CC) and flat washers (BB).
Repeat for this step to secure the short beam (D) to the small panels (B1 and B2).
Fig.5: Secure the lower connector 2 (F) and short netting tube (U) to the short beam (D) by using bolts (CC) and flat
washers (BB).
Fig.6: Secure the long netting tubes (T) to the long beams (C1 and C2) by using bolts (CC) and flat washers (BB).
Repeat this step to secure the short netting tubes.
Part Description Quantity Image
BBM6Flat washer38PCS
CCM6X15 Bolt18PCS
DDM6X20 Bolt20PCS
HardwarePack2
Fig.7: Secure top end of the slanting beam (H) to the top frame (G) by using bolts (DD) and flat washers (BB).
Fig.8: Secure the slanting beam (H) to the lower connector 1 (E) by using bolts (CC) and flat washers (BB).
Fig.9: Secure the middle beam (I) to the top beams (G) by using bolts (DD) and flat washers (BB).
Fig.10: Secure the lower end of the middle beam (I) the lower connector 2 (F) by using bolts (CC) and flat washers (BB).
Fig.11: Secure the small slanting beam (S) to the top frame (G) by
using bolts (CC) and flat washers (BB).
Fig.12: Secure the small slanting beam (S) to the small top
connector (Q) by using bolts (CC) and flat washers (BB).
Fig.13: Attach the hook (P) to the small top connector (Q).
Part Description Quantity Image
AAM6X35Bolt2PCS
BBM6Flatwasher16PCS
EEM6X15Screw14PCS
HardwarePack3
Fig.17: Insert the short PC 1 (J3) Short PC 2 (J4) into the middle beam (I) and slanting beam (H), then insert the rails (N1
and N2) into it. Insert the long PC (J1) into the middle beam (I) and slanting beam (H). Repeat this step to install the right
PCs.
Fig.18: Insert the middle PC (J5) into the middle beam (I); then insert the middle rail (N3) into it. Insert the middle PC (J5)
into middle beam (I).
Fig.19: Insert the plates (L1, L2 and L3) into the lower of the PCs; then secure the center plate (O1) to the middle beam (I)
through three holes by using screws (EE) and flat washers (BB).
Fig.20: Fig.20: Secure the corner plate (O2) to the slanting beam (H) through three holes by using screws (EE) and flat
washers (BB).
Fig.14: Insert the small PCs (K1 and K2) into the rail of the small slanting beam (S).
Fig.15: Insert the plates (M1 and M2) into the lower of the small PCs (K1 and K2), then secure the corner plate
(O2) to the small slanting beam (S) through three holes by using screws (EE) and flat washers (BB).
Fig.16: Secure the cover (R) to the small top connector (Q) by using bolts (AA) and flat washers (BB).
Part Description Quantity Image
GGRing 52PCS
HHΦ8X180Stake16PCS
HardwarePack4
Fig.21: Attach the mosquito net (V) to the long netting tubes (T) and short tubes (U) by using rings (GG).
Fig.22: Secure the whole gazebo to the ground by using stakes (HH).
IMPORTANT:
1. Keep all children and pets away from assembly area. Children and pets should be
supervised while gazebo is being assembled.
2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction
such as fence, garage, house, overhanging branches, laundry lines or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for
safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during
assembly.
5. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use.
6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the
gazebo in the ground. If you wish to secure the pavilion to a wood deck or concrete
surface, use 16 anchors suited to these surfaces (anchors not included).
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions
may require permits for installation and use. Some special procedures may be valid in
your area.
9. While this gazebo is manufactured to withstand strong force winds through only the
supplied ground stakes, in areas subject to frequent severe weather, securing the gazebo
to a deck, concrete patio or footings should be considered.
NOTE: The gazebo’s roof and structure are not guaranteed against extreme weather
conditions (storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow
must be cleaned off regularly. Any damage caused by snow accumulation is not covered
by the warranty.
Care & Maintenance:
Our steel components for garden accessories and furniture are treated with rust inhibiting
paint that protects it from rusting. However, due to the nature of steel, surface oxidation
(rusting) will occur once these protective coatings are scratched. This is not considered a
defect and thus not covered by the warranty.
To minimize this condition, we recommend care when assembling & handling the product
to prevent scratching the paint. Should any scratching or damage occur, we recommend
immediate touch-up with rust inhibiting paint.
Surface rust can also be easily removed with a very light application of common cooking
oil. If surface oxidation (rusting) occurs and if no measure is taken to prevent this, the
oxidation may start dripping on to deck or patio and caused damaging stains, which may
be difficult to remove. This can be prevented if the above-mentioned measures are taken
to keep the product from oxidizing.
DIRECTIVES D’ASSEMBLAGE DE L’ABRI-SOLEIL
Nos instructions claires et faciles à suivre vous aideront à assembler votre abri
facilement, du début à la fin. Le résultat sera un abri de haute qualité qui vous
offrira des années de plaisir.
Tout ce qu’il vous faudra sera un tournevis, un marteau et deux échelles d'au
moins 8 pi (2,5 m) de hauteur (non fournis).
Avis: CETTE UNITÉ EST TRÈS LOURDE!
Pour votre sécurité, N’ASSEMBLEZ PAS cet article tout seul. Deux
personnes seront requises pour une installation facile et en toute sécurité.
Identification des articles: pour faciliter leur identification, toutes les pièces sont
étiquetées pour correspondre au numéro de l’étape dans laquelle la pièce sera
employée.
Assurez-vous d’avoir l’aide de 6 personnes ou plus lors de l’assemblage ou
du déplacement du produit.
Indice
Lingue:
Manuali Casa da giardino popolari di altre marche
Mercia Garden Products
Mercia Garden Products 01DTSHPWOR1010DDOW-V4 Manuale di istruzioni
Palmako
Palmako Saale Manuale utente
Lemeks
Lemeks Palmako Kira EL16-3623 Manuale dell'installatore
Mercia Garden Products
Mercia Garden Products 0644LOG186-V4 Manuale di istruzioni
Palmako
Palmako Roger FR44-5953-2 Manuale utente
Mercia Garden Products
Mercia Garden Products 03DTSHHP1206HGD4MW-V1 Manuale di istruzioni
WAR-LOCK
WAR-LOCK GARDENSHED Skillion Series Manuale utente
Pergola kits USA
Pergola kits USA PREMIUM VINYL PAVILION Manuale utente
G21
G21 Boston 882 Manuale utente
Lemeks
Lemeks Palmako Grace PM56-4529 Manuale dell'installatore
Mercia Garden Products
Mercia Garden Products 03WES0808-V1 Manuale di istruzioni
Shire
Shire Salcey Manuale utente