Rosslare AY-Z12A Manuale utente

Long range Multi Reader

AY-Z12A

Installation Guide

December 2010

Table of Contents

AY-Z12A Installation Manual Page ii

Table of Contents

1. Introduction................................................................3

2. Technical Specifications...............................................4

3. Installation..................................................................5

3.1 The Installation Kit....................................................5

3.2 Installing the AY-Z12A Long Range Reader:............5

3.2.1. Single Reader Installation................................................ 6

3.2.2. Multiple Reader Installation............................................. 7

3.2.3. Installation process.......................................................... 7

4. Wiring and Configuration Instructions.........................8

4.1 Wiring instructions....................................................8

4.2 Single Reader Configuration...................................9

4.3 Multiple Reader Configuration..............................10

5. Operation Instructions ..............................................11

Appendix A. Limited Warranty .....................................12

Appendix B. Technical Support.....................................14

Introduction

AY-Z12A Installation ManualPage 3

1. Introduction

The AY-Z12A Long-range Reader is an RFID proximity card reader,

utilized with access control systems. The reader can function in

one of two scenarios

•Single reader installation (default)

•Multiple readers installation

Figure 1 The AY-Z12A Long-Range Reader

This Manual contains the following information:

•Installation

•Wiring Instructions

•Operation Instructions

Technical Specifications

AY-Z12A Installation Manual Page 4

2. Technical Specifications

Electrical Characteristics

Power Supply Type

Linear type - recommended

Operating Voltage Range

10 - 16VDC

Absolute Maximum

(non-operating)

18VDC

Input Current

Standby: 280mA

Read: 330mA

Tamper Output

Open collector, active low, max.

sink current 30mA

Maximum Cable Distance

500 ft (150 meters)

Card Read Distance

Weigand 26 output format with a

23.6" (60 cm) maximum read

range*

Environmental Characteristics

Operating Temp. Range

-22°F to 145° F (-30°C to 63°C)

Operating Humidity

0 – 95% (non-condensing)

Suitable for outdoor use (IP54)

Dimensions

Height x Width x Depth

11.81" x 11.81" x 1.0"

300mm x 300mm x 25.4 mm

Weight

2.35 Lbs. (1066g)

* For maximum range set the reader as a single reader, use Rosslare’s AT-R14

clamshell proximity card, as well as a 16 V power supply and ensure that the

installation is as far possible from any additional electrical devices and that it is not

in proximity to any metal.

Installation

AY-Z12A Installation ManualPage 5

3. Installation

3.1 The Installation Kit

The Installation kit comprises of the following items used during the

installation procedure:

•One Installation Template

•Four pan head screws & wall plugs

•One L shaped security screw tool

•Three Security screws

3.2 Installing the AY-Z12A Long Range Reader:

Figure 2: Removing the Top Cover

Figure 2 shows the front view of the AY-Z12A Long-Range Reader.

When installing the reader, you must remove the snap-off cover to

access the screw holes.

Installation

AY-Z12A Installation Manual Page 6

The Reader must be mounted with the appropriate screws (not

supplied), as described in the template provided.

Installing the unit on metal surfaces will reduce the read range

considerably, to decrease the affect of the metal surface use

Rosslare’s MP-Z02 Spacer (sold separately) as described in the

image below for a max range of 43cm (17 inch).

Figure 3: Installing the unit with the MP-Z02 spacer

3.2.1. Single Reader Installation

The AY-Z12A Long-Range Reader is designed to function with the

best performance when installed isolated from other AY-Z12A long

range readers at least in a range of 2-4 meters, the reader is

therefor preconfigured as a single installation reader. See Single

Reader Configuration, on page 9, for detailed configuration

instructions.

Installation

AY-Z12A Installation ManualPage 7

3.2.2. Multiple Reader Installation

Although designed to work in an isolated environment, it is

possible to install multiple readers within a range of 2-4 meters,

however the read range will reduce by 20-30 percent.

When installing multiple readers, configure each of the readers in

the close environment for multiple reader installation.

We do not recommend multiple readers be installed less than two

(2) meters apart due to reduced range caused by interference

between readers.

See Multiple Reader Configuration, on page 10, for detailed

configuration instructions.

3.2.3. Installation process

The physical installation of the unit is described below.

To Install the Reader:

1. Determine an approximate location for the installation of the

Reader.

2. Peel off the back of the self-adhesive installation label

template and locate it at the required location.

3. Using the template as a guide, drill holes (the size of which are

indicated in the template) to install the Reader or spacer onto

the surface.

4. Drill a 7/16” (10mm) hole for the cable. In the event that you

are installing the reader on metal, place a grommet or

electrical tape around the edge of the hole and use the MP-

Z02 spacer.

5. Route the interface cable from the Reader to the Controller. A

linear type power supply is recommended.

Wiring and Configuration Instructions

AY-Z12A Installation Manual Page 8

4. Wiring and Configuration Instructions

Follow the wiring and configuration instructions below based on

the installation type you are utilizing.

4.1 Wiring instructions

The AY-Z12A Reader is supplied with an 18” pigtail, comprising a 6-

conductor cable.

To connect the Reader to the Controller:

1. Prepare the Reader cable by cutting its jacket back 1¼” and

strip the insulation from the wires, ½”.

2. Prepare the Controller cable by cutting its jacket back 1¼”

and strip the insulation from the wires, ½”.

3. Splice the Reader’s pigtail wires to the corresponding

Controller wires and cover each joint with insulating tape.

If the tamper output is being utilized, connect the purple wire

to the correct input on the Controller.

Reader

Color

Weigand Output

10~16 VDC

Red

DC+Input

Shield / Ground Black Ground

Data 1

White

Data 1

Data 0

Green

Data 0

LEDCTL

Brown

LED Control

Tamper

Purple

Tamper

4. Trim and cover all unused conductors.

Wiring and Configuration Instructions

AY-Z12A Installation ManualPage 9

Note:

•The individual wires from the Reader are color-coded according

the Wiegand standard.

•When using a separate power supply for the Reader, this supply

and that of the Controller, must have a common ground.

•The Reader’s cable shield wire should preferably be attached

to an earth ground, or a signal ground

connection at the panel,

or power supply end of the cable. This configuration is best for

shielding the Reader cable from external interference

4.2 Single Reader Configuration

For single reader installation, follow the configuration process

below, this process is not required with new readers as it comes

preconfigured from the factory to function as a single door

reader.

To configure a single reader installation mode:

1. Turn the reader power OFF

2. Connect the Data 1 wire (White cable) to Ground.

3. Leave the LED Control wire (Brown cable) floating.

4. Turn the reader power ON

5. Connect the LED Control wire (Brown cable) to Ground.

– Reader LED turns Orange.

6. Release the LED Control wire from the Ground.

7. The Reader’s LED starts flashing continuously and the Buzzer

sounds.

8. Turn the reader power OFF

9. Disconnect the Data 1 wire (White cable) from the Ground.

10. The Reader configuration for single reader installation is

complete.

Altri manuali per AY-Z12A

Indice

Altri manuali Rosslare Lettore di schede

Rosslare

Rosslare AC-Q74 Istruzioni per il montaggio

Rosslare

Rosslare AY-x20 Series Manuale utente

Rosslare

Rosslare AY-K6255 Manuale utente

Rosslare

Rosslare MIFARE Classic AY 5B Series Manuale utente

Rosslare

Rosslare DR-12C Manuale utente

Rosslare

Rosslare AY-V12B Manuale utente

Rosslare

Rosslare AY-U920BT-US Manuale utente

Rosslare

Rosslare AY-U910 Manuale utente

Rosslare

Rosslare AYC-F60 Series Istruzioni per il montaggio

Rosslare

Rosslare DR-U955BT Manuale utente

Rosslare

Rosslare AY-V64B Istruzioni per il montaggio

Rosslare

Rosslare MIFARE Classic AY-25B Series Manuale utente

Rosslare

Rosslare AY-R12 Manuale utente

Rosslare

Rosslare DR-U955BT Manuale utente

Rosslare

Rosslare AY-D09M Istruzioni per il montaggio

Rosslare

Rosslare DR-12C Manuale utente

Rosslare

Rosslare MIFARE Classic AY-K6255 Manuale utente

Rosslare

Rosslare MIFARE AY-T6350 Istruzioni per il montaggio

Rosslare

Rosslare AY-K20C Manuale utente

Rosslare

Rosslare AYC-E60B Istruzioni per il montaggio

Rosslare

Rosslare AY-U9**BT series Manuale operativo

Rosslare

Rosslare CSN SMART AY-H6355BT Manuale utente

Rosslare

Rosslare Anti-Vandal MIFARE AY-Q6 60 Series Manuale utente

Rosslare

Rosslare AY-H12C Manuale utente

Manuali Lettore di schede popolari di altre marche

Lindy

Lindy 43185 Manuale utente

Lindy

Lindy 43185 Manuale utente

ViziT

ViziT RD-4F Manuale utente

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuale utente

AVID ID

AVID ID AVID1043 Manuale utente

Conrad

Conrad PCMCIA Manuale utente

Lindy

Lindy 51541 Manuale utente

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuale utente

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuale utente

ACS

ACS ACR122L Manuale utente

Secukey

Secukey S2-MF Manuale utente

Elecom

Elecom MR-SMC07 series Manuale utente

Alien

Alien ALR-9800 Manuale utente

ACS

ACS ACR310 Manuale utente

Datamars

Datamars R-IN1300 MID Manuale utente

Alarm Lock

Alarm Lock AL-PRE2 Manuale utente

xpr

xpr B100PROX-AH Guida utente

SimpleTech

SimpleTech FlashLink Manuale utente