Rosslare SA-23-B4 Manuale utente

AY-L23 and SA-23-B2/B4

Outdoor Long-Range RF Reader and Remote Controls

Installation and Operation Manual

1. Introduction

The AY-L23 is an outdoor long-range RF reader that acts as a receiver.

It is compatible with Rosslare’s SA-23 wireless remote control

transmitters:

SA-23-B2 – 2-Button Remote Control

SA-23-B4 – 4-Button Remote Control

The AY-L23 reader and the remote controls are available in both G

(433.92 MHz) and H (868.35 MHz) frequencies.

The AY-

L23 is not compatible with old remote controls such as:

SA-26, SA-27, and SA-28.

When the AY-L23 receives the a command signal from a SA-23-B2/B4

wireless transmitter, the AY-L23 outputs the ID to A_DATA0,A_DATA1

or B_DATA0,B_DATA1 to the attached controller and controls the

function of the relay (open drain FET) A or B according to the SA-23-B2

remote’s command.

The command signal consists of 3 parts:

ID (in Wiegand format)

ID output to A or B Wiegand Output according to the command in

SA-23-B2

Relay Function A or B according to command in the SA-23-B2

Figure 1: AY-L23 and SA-23-B2/B4

AY-L23 SA-23-B2 SA-23-B4

2. Technical Specifications

2.1 AY-L23

Input Voltage 7 to 24 VDC

Standby Current 26 mA (12 VDC)

Maximum Operating Current 65 mA (12 VDC)

Relay (FET, Open Drain) Current 200 mA (max voltage 40 V)

Tamper Output Open collector, active Open, max. sink

current is 16 mA

Maximum Cable Distance to

Controller

152 m (500 ft.)

Wiegand Output Format

Wiegand 26-Bit, 32-Bit, 34-Bit, 40-Bit

(decided by remote)

Frequencies G: 433.92 MHz

H: 868.35 MHz

Operating Temperature Range

-31°C to 63°C (-25°F to 145°F)

Operating Humidity Range 0 to 95% (non-condensing)

Suitable for outdoor use (IP65)

Dimensions (L x W x D) 145 x 43 x 20 mm (5.7 x 1.7 x 0.8 in.)

2.2 SA-23-B2/B4

Input Voltage 3 V Battery (CR 2450)

Standby Current < 1 uA

Max Operation Current 10 mA

ID Format Programmed to Wiegand 26-Bit

Frequencies G: 433.92 MHz (ASK)

H: 868.35 MHz (ASK)

Operating Temp. Range -31°C to 63°C (-25°F to 145°F)

Operating Humidity 0 to 95% (non-condensing)

Dimensions (L x W x D) 58 x 41 x 13.4 mm (2.3 x 1.6 x 0.5 in.)

Weight AY-L23: 100.8 g (3.56 oz)

SA-23: 21 g (0.74 oz) (without battery)

3. Mounting Instructions

Determine an appropriate mounting position for the receiver. Do not

mount the receiver near any source of wireless interference or on any

metal surface.

To mount the receiver:

1. Peel off the back of the self-stick mounting label template included

with the unit and place at the desired mounting position.

2. Using the template as a guide, drill two holes (hole size is indicated

on mounting template) for mounting the receiver to the surface.

3. Drill a 7/16” (10-mm) hole for the cable.

4. Remove the front case from the receiver.

5. Attach the receiver to the controller. (See wiring instructions)

6. Screw the receiver’s rear case onto its mounting location and

return the front case onto the mounted rear case.

The receiver is to be used with control panels whose power supply is

UL Listed Class 2 or equivalent.

4. Wiring Instructions

To connect the receiver to the controller:

1. Prepare the receiver cable by cutting the cable jacket back 1¼

inches and strip the wires ½ inch.

2. Prepare the controller cable by cutting the cable jacket back 1¼

inches and strip the wires ½ inch.

3. Splice the receiver’s pigtail wires to the corresponding controller

wires and cover each connection (see Table 1).

•The individual wires coming out of the receiver are color coded

according to the recommended Wiegand standard.

•When using a separate power supply for the receiver, this supply and

the controller’s power supply must have a common ground.

•The cable shield wire on the receiver should be attached to an Earth

ground (best) or signal ground connection at the panel or power

supply end of the cable. This configuration is best for shielding the

receiver cable from external interference.

Table 1: Wiring

Color Functionality

Red VIN (7–24 VDC)

Black GND

Dark Green A_Data0

White A_Data1

Orange A_LEDCTL (green LED)

Blue A-OUTPUT (FET, Open Drain)

Light Green B-DATA0

Gray B-DATA1

Brown B_LEDCTL (orange LED)

Yellow B-OUTPUT (FET, Open Drain)

Purple

TAMPER

5. 4BOperation

The AY-L23 works with any SA-23 remote and can operate two

Wiegand data outputs connected to the reader’s inputs at the access

control panel.

The AY-L23 LED is red in Operation mode.

5.1

Reader Mode

When pressing 1on the SA-23-B2/B4, the AY-L23 sends Wiegand

data-A. The LED changes to green for a short time with a beep.

When pressing 2on the SA-23-B2, the AY-L23 sends Wiegand data-B.

The LED changes to orange for a short time with a beep.

When pressing 2on the SA-23-B4, the AY-L23 sends ID+1 on Data A

line to the controller. The LED changes to green for a short time with a

beep.

5.2

Controller and Reader Mode

The AY-L23 can operate two OC outputs A/B with the SA-23-B2.

To activate the output from SA-23-B2, the remote button’s ID should

be registered first (Section 5.3).

In Controller and Reader mode, SA-23-B4 is not in use as it

does not activate any output of the AY-L23.

When pressing 1on the SA-23-B2, the AY-L23 sends Wiegand data-A

and activates out-A for 5 seconds.

When pressing 2on the SA-23-B2, the AY-L23 sends Wiegand data-B

and activates out-B for 5 seconds.

5.3 10BRegistering an ID

The AY-L23 can register up to 48 IDs with an SA-23-B2.

To register an ID:

1. Connect the orange and brown wires to GND.

2. Power on at Vin and GND.

After buzzer sounds 3 times, the LED turns green.

The AY-L23 is now in Register mode for 15 seconds.

3. Press 1on the SA-23-B2 remote.

If the registration is successful, you hear 2 short beeps.

If the ID was previously registered, you hear 2 long beeps.

If the limit of IDs (48) is reached, you hear have 3 long beeps.

4. Press 2on the SA-23-B2 remote.

If the registration is successful, you hear 2 short beeps.

If the ID was previously registered, you hear 2 long beeps.

If the limit of IDs (48) is reached, you hear have 3 long beeps.

Once the AY-L23 exits Register mode (after 15 seconds), you hear

a long beep.

Each of the 4 buttons of the B4 remote control is pre-

programmed with an ID that cannot be changed.

5.4 11BDeleting all IDs

To delete all IDs:

1. Connect the orange wire to GND.

2. Power on at Vin and GND.

After buzzer sounds 3 times, the LED turns orange for 2 seconds

and then turns green.

The AY-L23 is now in Delete mode for 5 seconds.

3. When the LED turns green, disconnect the orange wire from GND.

The LED changes from green to orange.

4. Re-connect the orange wire to GND within 5 seconds.

If all the IDs in reader are deleted successfully, the alarm

sounds 2 times and then you hear 3 short beeps.

If the deletions fails (times out), the reader outputs a long

beep.

6. Using the SA-23

The AY-L23 is used along with either the SA-23 2-button or 4-button

remote control.

The SA-23-B2 remote is programmed to:

Button 1 – Wiegand output to A DATA0/1 with A FET(relay)ON 5S

Button 2 – Wiegand output to B DATA0/1 with B FET(relay)ON 5S

The SA-23-B4 remote is programmed to:

Button 1 – Wiegand output to A DATA0/1 [ID number]

Button 2 – Wiegand output to A DATA0/1 [ID number+1]

Button 3 – Wiegand output to A DATA0/1 [ID number+2]

Button 4 – Wiegand output to A DATA0/1 [ID number+3]

6.1 Initial Setup

To set up the remote for use:

1. Install the battery.

The red LED turns on for 1 second, turns off 1 second and then

turns on for 1 second.

2. Check the distance range of the remote:

If the distance is set to long range (70 m), LED flashes on and

off 0.5 seconds 3 times.

If the distance is set to short range (15 m), LED flashes on and

off 0.1 seconds 6 times.

By default, the remote distance is set to 70 m.

6.2 Changing the Remote Distance Range

You can set the remote range to either 15 or 70 m.

To set the remote distance:

1. Remove the battery from the remote.

2. Press any button to reset the remote.

Any time you remove the battery from the SA-23, you must reset

the remote control by pressing any key to discharge the internal

capacitors.

3. Install the battery.

4. Press 1and 2together before the LED flashes for a second time.

The remote toggles to the other remote distance range.

If the distance is set to long range (70 m), LED flashes on and

off 0.5 seconds 3 times.

If the distance is set to short range (15 m), LED flashes on and

off 0.1 seconds 6 times.

6.3 Changing the ID of Button 2 (for SA23-

B2 only)

You can set Button 2 to transmit the same ID as Button 1 or to

transmit a unique ID. By default, Buttons 1 and 2 transmit the same ID

number.

To change the ID of Button 2 to be unique:

1. Remove the battery from the remote.

2. Press any button to reset the remote.

3. Press 2and install the battery until the red LED flashes quickly 5

times for 0.1 seconds.

Button 2will now use transmit a unique ID (ID of Button 1 +1)

4. Close the cover.

To change the ID of Button 2 to use ID of Button 1:

1. Remove the battery from the remote.

2. Press any button to reset the remote.

3. Press 1and install the battery until the red LED flashes quickly 5

times for 0.1 seconds.

Button 2will now transmit the same ID as Button 1.

4. Close the cover.

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate

the equipment.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Limited Warranty

The full ROSSLARE Limited Warranty Statement is available in the Quick

Links section on the ROSSLARE website at www.rosslaresecurity.com.

Rosslare considers any use of this product as agreement to the

Warranty Terms even if you do not review them.

Contact Information

United States and Canada

Rosslare Security Products, Inc.

Southlake, TX, USA

Toll Free: +1-866-632-1101

Local: +1-817-305-0006

Fax: +1-817-305-0069

support.na@rosslaresecurity.com

Europe

Rosslare Israel Ltd.

Rosh HaAyin, Israel

Tel: +972-3-938-6838

Fax: +972-3-938-6830

support.eu@rosslaresecurity.com

Latin America

Rosslare Latin America

Buenos Aires, Argentina

Tel: +54-11-4001-3104

support.la@rosslaresecurity.com

China

Rosslare Electronics (Shenzhen) Ltd.

Shenzhen, China

Tel: +86-755-8610-6842

Fax: +86-755-8610-6101

support.cn@rosslaresecurity.com

Asia Pacific, Middle East, Africa

Rosslare Enterprises Ltd.

Kowloon Bay, Hong Kong

Tel: +852-2795-5630

Fax: +852-2795-1508

support.apac@rosslaresecurity.com

India

Rosslare Electronics India Pvt Ltd.

Tel/Fax: +91-20-40147830

Mobile: +91-9975768824

sales.in@rosslaresecurity.com

www.rosslaresecurity.com

0706-0960503+04

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Rosslare Telecomando

Rosslare

Rosslare SA-33 Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione