RS PRO S1 Manuale utente

Instruction Manual

S1 & S2 & S3

Digital Multimeter



rspro.com

S1 &S2 & S3 / EN

Warning

. . . . . . . . . .

. . . . . . . .

Safety sheet

. . . . . . . . .

. . . . . . . . . .

. . . . . . . .

. . . . . . . . .

Read First

Safety Information

Understand and follow operating instructions carefully. Use the

meter only as .

 WARNING

• If the equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may

be impaired.

• Always use proper terminals, switch position, and range for

measurements.

• To reduce the risk of fire or electric shock, do not use this

product around explosive gas or in damp locations.

• Verify the Meter operation by measuring a known voltage.

If in doubt, have the Meter serviced.

• Do not apply more than the rated voltage, as marked on

Meter, between terminals or between any terminal and earth

ground.

• To avoid false readings that can lead to electric shock and

injury, replace the battery as soon as low battery indicator

blinks.

• Avoid working alone so assistance can be rendered.

• Do not use the Tester if the Tester is not operating properly

or if it is wet.

• Individual protective device must be used if hazardous live

parts in the installation where the measurement is to be carried

out could be accessible.

• Disconnect the test leads from the test points before changing

the position of the function rotary switch.

• Never connect a source of voltage when the function rotary

switch is not in voltage position.

• When using test leads or probes, keep your fingers behind

the finger guards.

• Use caution with voltages above 30 Vac rms, 42 Vac peak, or

60 Vdc. These voltages pose a shock hazard.

• Remove test lead from Meter before opening the battery door

or Meter case.

• DO NOT USE the test leads when the internal white

insulation layer is exposed.

Warning Safety sheet

S1 &S2 & S3 / EN

• DO NOT USE the test leads above maximum ratings of CAT.

environment, voltage and current, that are indicated on the

probe and the probe tip guard cap.

• DO NOT USE the test leads without the probe tip guard cap

in CAT III and CAT IV environments.

• Probe assemblies to be used for MAINS measurements shall

be RATED as appropriate for MEASUREMENT CATEGORY

III or IV according to IEC 61010-031 and shall have a voltage

RATING of at least the voltage of the circuit to be measured.

• Only replace the blown fuse with the proper rating as specified

in this manual.

• Do not attempt a current measurement when the open voltage

is above the fuse protection rating. Suspected open voltage

can be checked with voltage function.

• Never attempt a voltage measurement with the test lead

inserted into the A input terminal.

• Disconnect circuit power and discharge all high-voltage

capacitors before testing resistance, continuity, diodes, or

capacitance.

S1 &S2 & S3 / EN

Risk of electric shock

See instruction manual

DC measurement

AC measurement

Bluetooth

HBoth direct and alternating current

Equipment protected by double or reinforced insulation

Low battery

Fuse

Earth

Conforms to EU directives

EApplication around and removal from

hazardous live conductors is permitted

Do not discard this product or throw away.

Attention! Magnets might affect the correct functioning

of cardiac pacemakers and implanted defibrillators.

As a user of such medical devices, keep a sufficient

distance to the magnet.

Symbols as marked on the Meter and Instruction

manual

Unsafe Voltage

To alert you to the presence of a potentially hazardous voltage,

when the Tester detects a voltage ≧30 V or a voltage overload

(OL) in V, mV, AutoV, PV. The symbol is displayed.

Maintenance

Do not attempt to repair this Meter. It contains no user service-

able parts. Repair or servicing should only be performed by

qualified personnel.

Cleaning

Periodically wipe the case with a dry cloth and detergent.

Do not use abrasives or solvents.

S1 &S2 & S3 / EN

Introduction

The Meter Description

Front Panel Illustration

1. Volt Seek Light

2. 6,000 count digital display

3. Push-buttons.

4. Rotary switch for turn the Power On / Off and select the function.

5. Input Terminal for Multi-function.

6. Common (Ground reference) Input Terminal.

7. Input Terminal for A.

A COM

Volt Seek

Volt Seek Light

LCD Display

Button

Rotary Switch

V,Ω, %,°C Input (or “+”)

Common Input

A Input

S1 &S2 & S3 / EN

Features

Function S1 S2 S3

ACV ✓✓✓

DCV ✓✓✓

DC mV ✓✓✓

Frequency ✓✓✓

Resistor ✓✓✓

Continuity ✓✓✓

Diode ✓✓✓

Capacitor ✓✓✓

Bluetooth ✓✓✓

Volt Seek ✓✓✓

AutoV LoZ ✓✓

Data Logger ✓✓✓

HFR ✓✓✓

Backlight ✓✓✓

Bar Graph ✓✓✓

ACA ✓✓

DCA ✓✓

Temperature ✓✓

AC µA/mA ✓

DC µA/mA ✓

PV Voltage ✓

S1 &S2 & S3 / EN

Making Basic Measurements

CAUTION

When connecting the test leads to the DUT (Device Under

Test) connect the common test leads before connecting the

live test leads ; when removing the test leads, remove the live

test leads before removing the common test leads.

Measuring Voltage

Preparation and Caution Before Measurement

Observe the rules of Warnings and Cautions.

Dial the switch to select the measuring function.

CAUTION

Do not use the LoZ mode to measure voltages in circuits that

could be damaged by this mode’s low impedance.

S1 &S2 & S3 / EN

Measuring PV Voltage

Dial the switch and press the Function button to select the

measuring function.

CAUTION

This function is only available with the dedicated PV test

probe.

Always select correct DC / AC mode to perform high voltage

measurement. This meter will flash symbol and the correct

mode symbol (AC / DC) if the input voltage is different and

dangerous.

S1 &S2 & S3 / EN

Measuring Current

Dial the switch and press the Function button to select the

measuring function

Disconnect

S1 &S2 & S3 / EN

Measuring Capacitance / Diode

Dial the switch and press the Function button to select the

measuring function

Measuring Continuity / Resistance

Dial the switch and press the Function button to select the

measuring function

Red Black

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali RS PRO Multimetro

RS PRO

RS PRO RS-965T Manuale utente

RS PRO

RS PRO IDM-8351 Manuale utente

RS PRO

RS PRO ICM 139R Manuale utente

RS PRO

RS PRO RS-9889 Manuale utente

RS PRO

RS PRO IPM 138N Manuale utente

RS PRO

RS PRO IDM201N Manuale utente

RS PRO

RS PRO IDM 71 Manuale utente

RS PRO

RS PRO IDM-8341 Series Manuale utente

RS PRO

RS PRO RS-660 Manuale utente

RS PRO

RS PRO RS-9663 Manuale utente

RS PRO

RS PRO RS-9963T Manuale utente

RS PRO

RS PRO RS-989 Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

RS PRO

RS PRO RS-946 Manuale utente

RS PRO

RS PRO IDM93N Manuale utente

RS PRO

RS PRO ICM33II Manuale utente

RS PRO

RS PRO LCR 1701 Manuale utente

RS PRO

RS PRO RS-9660B Manuale utente

RS PRO

RS PRO RS-218 Manuale utente

RS PRO

RS PRO IDM 98IV Manuale utente

RS PRO

RS PRO RS-338 Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

RS PRO

RS PRO ICM 135R Manuale utente

RS PRO

RS PRO RS-927A Manuale utente

Manuali Multimetro popolari di altre marche

Agilent Technologies

Agilent Technologies 34420A Manuale utente

Fluke

Fluke 83 Manuale utente

Hameg

Hameg HM 8012 Manuale utente

Mastech

Mastech MY70 Manuale utente

Steren

Steren MUL-300 Manuale utente

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuale utente

PeakTech

PeakTech 4000 Manuale per l'uso e la cura

YOKOGAWA

YOKOGAWA 90050B Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuale utente

Fluke

Fluke 8846A Manuale operativo e di manutenzione

Tempo Communications

Tempo Communications MM200 Manuale utente

Elenco Electronics

Elenco Electronics CM-1555 Manuale utente

Mastech

Mastech MS8238C Manuale utente

SDAR

SDAR 830A, 830B, 830D, 830C Manuale utente

BGS technic

BGS technic 8890 Manuale utente

Amprobe

Amprobe Hexagon 60 Manuale utente

Morris

Morris 57074 Manuale utente