Ruckus Wireless C500 Manuale utente

Published 30 April 2015, Part Number 800-70788-001 Rev A

Page 1 of 4

C500 Access Point

Quick Setup Guide

This Installation Guide provides information on how to configure the

Ruckus Wireless ZoneFlex C500 802.11ac dual band two-stream access

point (AP) with integrated cable modem (CM). The C500 supports dual-

band 2.4GHz and 5GHz concurrent operation with internal antennas.

The C500 is placed on a desktop, or can be wall mounted using a

separately-ordered wall bracket (part number 902-0121-0000). After

completing the steps described in this Guide, you will be able to use the

C500 at your site.

The C500 access point with integrated cable modem is referred to in the

rest of this document as the C500.

This Guide in Other Languages

请从以下网站获得该指南的简体中文版

https://support.ruckuswireless.com

Vous trouverez la version française de ce guide à l'adresse suivante

https://support.ruckuswireless.com

このガイドの日本語版は https://support.ruckuswireless.com

でご覧ください

이가이드의 한국어 버전은 웹사이트

(https://support.ruckuswireless.com)에서 확인하시기 바랍니다

Veja a versão em português (Brasil) deste guia em

https://support.ruckuswireless.com

Puede ver la versión en español (América Latina) de esta guía en

https://support.ruckuswireless.com

Before You Begin

Before deploying Ruckus Wireless products, please check for the latest

software and the release documentation.

• User Guides and Release Notes are available at

http://support.ruckuswireless.com/documents

• Software Upgrades are available at

http://support.ruckuswireless.com/software

• Open Source information is available at

http://opensource.ruckuswireless.com

• Software License and Limited Warranty are available at

http://support.ruckuswireless.com/warranty

Safety Warnings

•WARNING! Only trained and qualified personnel should be allowed to

install, replace, or service this equipment. The professional installer is

responsible for the proper installation and configuration of this C500.

The C500 installation must comply with local regulatory requirements,

especially with those regulating operation near military and/or weather

radar systems.

•WARNING! Installation of this equipment must comply with local and

national electrical codes.

•WARNING! Ruckus Wireless strongly recommends that you wear eye

protection before mounting the C500.

Package Contents

Before configuring or deploying your C500, verify that all items listed below

are included in the package. If any item is damaged or missing, notify your

authorized Ruckus Wireless sales representative.

• One 901-C500-xxyy access point with integrated cable modem (A in

Figure 1), where ‘xx’ is a country-specific code; and ‘yy’ is the code for

the cable modem: ‘31’ is DOCSIS 3.0 and ‘41’ is EuroDOCSIS

• One 1.8m (6’) IEC 320 power cord (B in Figure 1)

• One 902-1169-xx00 power adapter (C in Figure 1)

• Service Level Agreement/Limited Warranty Statement

• Regulatory Statement

• Declaration of Conformity, if required

• This Quick Setup Guide

If you are mounting the C500 on a wall, then you will also need:

• One customer-ordered 902-0121-0000 C500 wall bracket kit

Figure 1. C500 package contents

LEDs and Connectors

The C500 has seven LEDs visible on the front panel, and three connectors

and a reset button on the back panel. Refer to Table 1 for a description of

the front-panel LEDs and their indications. Refer to Table 2 for a

description of the back-panel connectors and the reset button.

Continue with the following:

•Configuring the C500 (optional)

•Verifying CM and AP Operation

•What to Do Next

•Operating and Troubleshooting the C500

•Physical Installation

Note: The minimum software revision for the C500 is RuckOS 3.1.1

or later.

Table 1. Front-panel LED indications

LED Indications

PWR • Red = Booting.

• Green = Normal operation.

DS (CM) • Blinks green when searching for downstream (DS), then

solid green when DS is locked. Also blinks green during CM

boot when power is applied.

US (CM) • Off when DS is searching, and then blinks green as

upstream power is increased/ranged and then solid green

when upstream ranging is complete. Also blinks green

during CM boot when power is applied.

ON-LINE

(CM)

• Off until CM DS and CM US are solid ON, then blinks green

as the CM obtains an IP address and a configuration file,

and then comes online and LED is solid green. Also blinks

green during CM boot when power is applied.

CTL • Off = Always off.

2.4G • Off: The WLAN service is down.

• Amber: The WLAN is up, but no clients are associated/

connected.

• Green: The WLAN is up and at least one client is associated.

5G • Off: The WLAN service is down.

• Amber: The WLAN is up, but no clients are associated/

connected.

• Green: The WLAN is up and at least one client is associated.

Table 2. Back-panel connectors and reset button

Connector

or Button

Description

• RJ-45 1000BASE-T Ethernet connector, with Link and

Activities LEDs.

12VDC • Receives 12 VDC input from a factory-supplied 100-

250VAC 50-60Hz external wall adapter.

RESET • Press and hold in this button for four seconds to reset the

AP and CM to their factory settings. Refer to Note in

Operating and Troubleshooting the C500.

(coaxial

connector)

• RG59 coax cable connector input to the CM.

Published 30 April 2015, Part Number 800-70788-001 Rev A

Page 2 of 4

CONFIGURING THE C500 (OPTIONAL)

Note: The C500 normally receives its latest AP and CM firmware

downloads and initial configurations from the cable modem termination

system (CMTS) high speed data services equipment when it powers up; if

this is the case, then skip this section and continue with Verifying CM and

AP Operation.

If the C500 AP and CM do not receive their latest firmware downloads and

initial configurations from the CMTS equipment when the C500 powers up,

then continue with these procedures:

•Step 1: Collecting Setup Requirements, Hardware, and Tools

•Step 2: Powering Up the C500

•Step 3: Connecting Your Computer to the C500

•Step 4: Preparing Your Computer for C500 Setup

•Step 5A: Operating the CM

•Step 5B: Configuring the AP for Standalone Operation

Step 1: Collecting Setup Requirements, Hardware,

and Tools

• A computer with Ethernet adapter running Windows 7 or equivalent,

with Firefox or equivalent web browser, and Telnet or SSH (secure

shell) programs. (Procedures for common operating systems are

similar.)

• One Cat 5e (or better) Ethernet cable.

Continue with Step 2: Powering Up the C500.

Step 2: Powering Up the C500

1After removing your C500 from its package, place it next to your com-

puter.

2Use the power cord to power on the 740-64245-011 power adapter.

3Plug the power adapter output cable into the power connector on the

back of the C500.

4Wait until the C500 PWR, DS, US, and ON-LINE LEDs stop flashing

and then remain on.

Continue with Step 4: Preparing Your Computer for C500 Setup.

Step 3: Connecting Your Computer to the C500

1Using an Ethernet cable, connect your computer’s network port to the

Ethernet port on the back of the C500.

Continue with Step 5A: Operating the CM.

Step 4: Preparing Your Computer for C500 Setup

NOTE: The following procedures assume that Windows 7 is the operating

system. Procedures for other operating systems are similar.

1On your Windows 7 computer, configure your network adapter from

the Local Area Connection settings as follows:

•Start > Control Panel > Network and Sharing Center >

Change Adapter Settings

2Edit the TCP/IPv4 address settings as follows:

•Local Area Connection > Properties > Internet Protocol

Version 4 (TCP/IPv4) > Properties

The Internet Protocol Version 4 (TCP/IPv4) Properties dialog box

appears.

IMPORTANT! Write down all of the currently active settings so you

can restore your computer to its current configuration when this pro-

cedure is completed.

3Select Obtain an IP address automatically and Obtain DNS server

address automatically. Avoid 192.168.100.1 which is the default CM

address, and 192.168.100.2 which is the AP default IP address.

4Click OK twice to save your changes.

Your changes are put into effect immediately. Continue with Step 5A:

Operating the CM or Step 5B: Configuring the AP for Standalone

Operation.

Step 5A: Operating the CM

Note: If the C500 CM is going to be managed by a CMTS, then skip this

section and continue with Step 5B: Configuring the AP for Standalone

Operation.

Note: The CM and AP each have their own independent firmware load that

are each updated independently.

Continue with Logging Into the CM Web Interface via the Ethernet Port or

Logging Into the CM Web Interface via a Dynamic IP Address.

Logging Into the CM Web Interface via the Ethernet Port

1Complete Step 1: Collecting Setup Requirements, Hardware, and

Tools through Step 4: Preparing Your Computer for C500 Setup.

2On the administrative computer, open a web browser window.

3In the address or location bar, type the CM IP address, for instance:

192.168.100.1

--OR--

<DHCP-assigned CM IP address>

The CM web interface displays a login prompt.

4Leave User Name blank.

5In Password, type ADMIN.

6Click Log In. The Connection Status page appears, indicating that you

have successfully logged on to the CM web interface.

Continue with Viewing the Software Status

Logging Into the CM Web Interface via a Dynamic IP

Address

1Complete Step 1: Collecting Setup Requirements, Hardware, and

Tools through Step 4: Preparing Your Computer for C500 Setup.

2Connect the administrative computer to the same subnet as the C500.

3On the administrative computer, start a Web browser.

4In the address bar, enter the IP address that is assigned to the CM by

the CMTS. The CM web interface displays a login prompt.

5Leave User Name blank.

6In Password, type ADMIN.

7Click Log In. The Connection Status page appears, indicating that you

have successfully logged on to the CM web interface.

8Continue with any or all of the following:

•Viewing the Software Status

•Viewing the Connection Status

•Configuring the Downstream Frequency

•Administering CM Passwords

Viewing the Software Status

The Software Status page displays the current CM installed software

version and the CM system status.

1Log into to the Connection Status page as described in Logging Into

the CM Web Interface via the Ethernet Port or Logging Into the CM

Web Interface via a Dynamic IP Address.

2In the left sidebar, click Software. The CM displays the Software Sta-

tus page.

There are two tables on the Software Status page – Information and

Status. Table 3 and Table 4 describe the information that these tables

display.

Viewing the Connection Status

The Connection Status page displays information about the CM’s Hybrid

Fiber Coax (HFC) and IP network connectivity, including its downstream

and upstream channels and the IP address that is currently assigned to the

CM.

1Log into to the Connection Status page as described in Logging Into

the CM Web Interface via the Ethernet Port or Logging Into the CM

Web Interface via a Dynamic IP Address.

2Click Connection in the left sidebar. The CM web interface displays

the Connection Status page.

Note: The Downstream Power indicated in the Power column is accu-

rate to +/-3dB.

Table 3. Information (software) table

Item Description

Standard Specification

Compliant

The standard with which the device is

compliant.

Hardware Version The version of the CM hardware.

Software Version The version of the CM software.

Cable Modem MAC Address MAC address.

Cable Modem Serial Number Serial number.

CM Certificate Indicates whether a security certificate

is installed.

Table 4. Status table

Item Description

System Up Time Indicates the time that has elapsed

since the CM was last rebooted.

Network Access Indicates whether or not the CM is

connected to the network.

Cable Modem IP Address IP address.

Published 30 April 2015, Part Number 800-70788-001 Rev A

Page 3 of 4

Configuring the Downstream Frequency

The Configure Status page allows you to set the downstream frequency for

the CM. Configuring the downstream frequency enables the device to

quickly obtain a direct frequency lock with the CMTS upon bootup and

helps to save several minutes of scanning for an available downstream

frequency from the CMTS.

1Log into to the Connection Status page as described in Logging Into

the CM Web Interface via the Ethernet Port or Logging Into the CM

Web Interface via a Dynamic IP Address.

2Click Configure in the left sidebar. The CM web interface displays the

Configure Status page.

3In the Configure DS Frequency text box, enter the downstream fre-

quency (in Hertz) that you want the CM to use to connect to the CMTS

when it boots up.

4Click Set Values and Reboot to have the CM save your changes and

reboot.

Administering CM Passwords

The parameters on the Security Status page allow you to change the CM

1Log into to the Connection Status page as described in Logging Into

the CM Web Interface via the Ethernet Port or Logging Into the CM

Web Interface via a Dynamic IP Address.

2Click Security in the left sidebar. The CM web interface displays the

Security Status page.

Ruckus Wireless recommends that you change the login and password as

follows:

1Enter a new CM user ID in Password Change User ID.

2Enter a new CM user password in New Password.

3To change the password re-enter the new CM user password in Re-

Enter New Password.

4Enter the existing (before change) CM user password in Current User

ID Password.

Restore the factory defaults as follows:

1Select the Restore Factory Defaults Yes button to reset all the CM

parameters to the factory default settings after the next reboot.

Select the Restore Factory Defaults No button to prevent resetting all

CM parameters to the factory defaults after the next reboot.

2If you have made any changes on the Security Status page, then click

Apply.

If you have selected Restore Factory Defaults Yes, then the CM

reboots and resets all CM parameters to the factory defaults.

If you have selected Restore Factory Defaults No, then the CM web

interface saves your changes and returns you to the Security Status

page.

Continue with Step 5B: Configuring the AP for Standalone Operation.

Step 5B: Configuring the AP for Standalone

Operation

Note: If the C500 is going to be managed by an AP controller or manager,

then skip this section and continue with Verifying CM and AP Operation.

Refer to the following:

•Logging Into the AP’s Web Interface

•Configuring Common Wireless Settings

•Configuring Wireless LAN Settings

Logging Into the AP’s Web Interface

1Collect the AP MAC address (12 alphanumeric digits) from the outside

of the AP case.

2Complete Step 1: Collecting Setup Requirements, Hardware, and

Tools through Step 4: Preparing Your Computer for C500 Setup.

3In an administrative computer address or location bar, type the follow-

ing address:

https://192.168.100.2

--OR--

4Press <Enter>. A security alert message appears.

5Click Yes or OK or Proceed anyway (depending on the browser) to

continue. The AP’s login page appears.

6In User name, type super.

7In Password, type sp-admin.

8Click Login. The web interface displays the Status > Device page.

Continue with Configuring Common Wireless Settings.

Configuring Common Wireless Settings

The settings on the Common page are required to enable wireless devices

to associate with the AP.

Note: The AP has one 2.4GHz radio and one 5GHz radio. The wireless

settings for each radio need to be configured separately on the Web

interface. To configure the 2.4GHz radio settings, click Configuration >

Radio 2.4G. To configure the 5GHz radio settings, click Configuration >

Radio 5G.

1On the left menu of the Web interface, click Configuration > Radio

{2.4G/5G}. The Common page appears.

2Verify that the common wireless settings are configured as listed in

Table 5.

3If you made any changes to the Common page, then click Update

Settings.

4Repeat Step 1 through Step 3 for Configuration > Radio 5G.

Continue with Configuring Wireless LAN Settings.

Configuring Wireless LAN Settings

The settings on at least one Wireless # (Wireless LAN Number) page are

required to enable wireless devices to associate with the AP. The default

wireless settings are listed in Table 6.

1Click one of the Wireless # tabs. The selected Wireless # page

appears.

2In Wireless Availability, click Enabled.

3In Broadcast SSID, click Enabled.

4Clear the SSID box, and then type a unique and descriptive name that

you want to call this wireless network.

For example, you can enter Ruckus Wireless AP. This SSID is the

name that helps users identify this wireless network in their wireless

network connection application.

Note: You can also configure other wireless settings on this and other

Wireless # pages (in addition to the settings described above),

although it is not necessary for completing the AP installation.

5Click Update Settings. You have completed configuring the basic

wireless settings of the AP.

Continue with Verifying CM and AP Operation.

Table 5. Common wireless configuration

Setting Recommended Value

Wireless Mode • 2.4GHz (802.11b/g/n) for Configuration > Radio

2.4G > Common.

• 5GHz (802.11ac/a/n) for Configuration > Radio

5G > Common.

Channel SmartSelect.

Channel Width 20 MHz.

Country Code If you purchased the AP in the United States of

America, this value is fixed to United States at the

factory and is not user configurable.

If you purchased the AP outside the United States of

America, verify that the value is set to your country or

region. Selecting the correct country code ensures

that the AP uses only the radio channels allowed in

your country or region.

Note: The two radios on the Ruckus Wireless AP are always configured

with the same country code setting. If you change the country code for

Radio 2.4G, for example, the same change is automatically applied to

Radio 5G.

Table 6. Default wireless settings

Setting Default Value

SSID (network

name)

Wireless 1 to Wireless 8 (8 WLANs).

Encryption

Method (security)

Disabled on all WLANs.

Published 30 April 2015, Part Number 800-70788-001 Rev A

Page 4 of 4

VERIFYING CM AND AP OPERATION

The cable operator has their own CM and AP acceptance tests. Make sure

you verify the C500 operation as defined in the acceptance tests before

leaving the installation site.

WHAT TO DONEXT

Following are some of the post-installation tasks that Ruckus Wireless

recommends. Refer to the Ruckus Wireless Indoor Access Point User

Guide for more information on configuring and managing the AP.

Changing the Administrative Password

Management access to the Web interface of the AP is controlled through

administrative user name and password. As soon as you complete the AP

setup, make sure you log on to the AP’s Web interface and change the

default administrative user name and password. This will help prevent

unauthorized users from logging in to the AP’s Web interface and changing

the AP settings to compromise your network.

Configuring the Security Settings

Unlike wired networks, anyone with a compatible wireless adapter can

receive wireless data transmissions from your network. To prevent

unauthorized users from entering your wireless network and accessing

your computers and files, Ruckus Wireless strongly recommends enabling

and configuring wireless security on the AP. The AP supports several types

of encryption and authentication methods to help prevent unauthorized

access to your wireless network.

Configuring Advanced Settings and Features

The AP has been configured for basic operation. However, the Ruckus

Wireless AP supports many advanced settings and features. Refer to the

Ruckus Wireless Indoor Access Point User Guide for instructions on how

to configure the advanced setting and feature parameters.

Reading Related Documentation

The latest versions of Ruckus Wireless product documentation are

available for download on the Ruckus Wireless Support Web site at

http://support.ruckuswireless.com/documents

Online Training Resources

To access a variety of online Ruckus Wireless training modules, including

free introductory courses to wireless networking essentials, site surveys,

and Ruckus Wireless products, visit the Ruckus Wireless Training Portal at

https://training.ruckuswireless.com

OPERATING AND TROUBLESHOOTING THE

C500

This section lists some information that may be useful in operating and

troubleshooting the C500. Topics include:

•Rebooting and Resetting the C500

•How Radio Frequency Scanning Works

•Retrieving the CM’s MAC Address

Rebooting and Resetting the C500

CAUTION: If required, you can reset the C500 to its factory default settings

by pressing and holding in the reset button on the back of the C500 for

four or more seconds. DO NOT DO THIS UNLESS SO INSTRUCTED.

(Doing this resets the C500 IP address to 192.168.100.2 and resets the

C500 CM address to 192.168.100.1.)

NOTE: After a reset, you can access the internal C500 AP web interface

using https://192.168.100.2. Your device must use an unused IP

address, with subnet mask 255.255.255.0. The username is super, and

the password is sp-admin.

How Radio Frequency Scanning Works

•DOCSIS Radio Frequency Scanning

•EuroDOCSIS Radio Frequency Scanning

DOCSIS Radio Frequency Scanning

The following steps describe how a DOCSIS-compliant C500 performs

radio frequency scanning:

1Looks at the last “known good channel” (repeat this every 64 channel

checks).

2Checks the sixteen last known frequencies (repeat this every 32 chan-

nel checks).

3Scans STD standard channels (where the center of the channel is an

integer spaced by 6MHz), first [from 93MHz to 999MHz - 152 chan-

nels]).

4Scans the harmonically related carrier (HRC) channels, which moves

the channels 1.25MHz off the standard frequencies so the video carri-

ers are all related by 6MHz [from 91.75 to 997.5MHz--152 channels].

A complete frequency scan requires approximately 469 channel checks.

Since each channel takes about 0.6 seconds, a full scan is done every 281

seconds (a little under five minutes).

Note: The scanning of generic DOCSIS channels is required the first time

the C500 connects to an MSO. After the initial scan, the C500 is able to

retrieve the local country frequency plan without a complete scan during its

normal operation.

EuroDOCSIS Radio Frequency Scanning

The following steps describe how a EuroDOCSIS-compliant C500

performs radio frequency scanning:

1The cable modem scans DS frequencies in descending order in a

group of four adjacent frequencies 8 MHz apart.

The step between groups is 250kHz.

From 122250000 Hz down, the scanning is not done in groups and

descends in 250kHz steps to the lowest frequency of 112 MHz.

2There is a scan list that keeps the 16 LKFs (Last Known Frequencies).

They are re-scanned every 32 channels.

3The first entry in the scan list is re-scanned every 64 channels.

A complete frequency scan requires approximately 4526 channel checks

and lasts approximately 4525 seconds.

Retrieving the CM’s MAC Address

There are some configuration operations that require you to enter the CM’s

MAC address. The CM and AP MAC addresses are printed on labels on

the outside of the C500. If you cannot find the CM’s MAC address on the

C500, you can use the CMTS to retrieve the CM’s MAC address.

PHYSICAL INSTALLATION

• Place the C500 on a flat surface with feet down for most installations.

You will experience the best wireless coverage and throughput when

the C500 is mounted upright. Make sure you do not place the C500

on a hot surface or in direct sunlight.

• If you are mounting the C500 on a wall or other vertical surface, then

refer to the C500 Accessory Bracket Mounting Guide. Make sure you

do not mount the C500 on a hot surface or in direct sunlight.

Altri manuali Ruckus Wireless Punto di accesso wireless

Ruckus Wireless

Ruckus Wireless T300 Manuale di istruzioni per l'installazione

Ruckus Wireless

Ruckus Wireless ZoneFlex series Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex 7761-CM Manuale utente

Ruckus Wireless

Ruckus Wireless SmartCell 8800-S Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762 Manuale utente

Ruckus Wireless

Ruckus Wireless MediaFlex 2900 Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex R700 Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex series Manuale utente

Ruckus Wireless

Ruckus Wireless C110 Manuale utente

Ruckus Wireless

Ruckus Wireless SmartZone 300 Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex 7782-E Manuale di istruzioni per l'installazione

Ruckus Wireless

Ruckus Wireless VF2811 Manuale utente

Ruckus Wireless

Ruckus Wireless Xclaim Xi-2 Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex 901-T504-US31 Manuale utente

Ruckus Wireless

Ruckus Wireless T710 Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex 7762-T Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex 2741 802.11g Manuale utente

Ruckus Wireless

Ruckus Wireless R350 Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex series Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex 7782 Manuale di istruzioni per l'installazione

Ruckus Wireless

Ruckus Wireless ZoneFlex series Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex R500 Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex R710 Manuale utente

Ruckus Wireless

Ruckus Wireless ZoneFlex 7352 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente