S.R.Smith Rogue2 Manuale utente

06-821 S.R. SMITH, LLC 2013 OCT14

ROGUE2

SLIDE OWNER’S MANUAL

SRS AUSTRALIA, PTY LTD

12 Enterprise St

Richlands QLD 4077

Australia

Phone 07 3812 2283 •Fax 07 3812 1187

www.srsmith.com/au

S.R. SMITH, LLC

CORPORATE HEADQUARTERS

P.O. Box 400 • 1017 S.W. Berg Parkway

Canby, Oregon 97013

USA

Phone (503) 266 2231 • Fax (503) 266 4334

www.srsmith.com

TABLE OF CONTENTS

SLIDE WARNING AND SAFETY SUMMARY........................................................................................................2

INTENDED USE INSTRUCTIONS...........................................................................................................................3

INSTALLED ROGUE2 STRUCTURAL & INSTALLATION CHECKLIST ...........................................................4

DAILY/WEEKLY MAINTENANCE OF THE ROGUE2 ..........................................................................................5

APPLICABLE STANDARDS AND CODES ............................................................................................................5

ASSEMBLY AND INSTALLATION...........................................................................................................................5

DRAWINGS.................................................................................................................................................................5

SUBSEQUENT OWNERS.........................................................................................................................................5

MANUFACTURER’S PLACEMENT INSTRUCTIONS..........................................................................................6

CLEANING INSTRUCTIONS....................................................................................................................................8

SLIDE WARNING AND SAFETY SUMMARY

DANGER –FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS AND THE

OWNER’S MANUAL MAY RESULT IN SEROUS INJURY OR DEATH

HEAD FIRST SLIDES ARE STRICTLY PROHIBITED

TO REDUCE THE POSSIBILITY OF INJURY, IT IS NECESSARY THAT THE USER

KNOW THAT THE CHIEF DANGER OF HEAD FIRST SLIDING IS SERIOUS SPINAL

INJURY. INJURIES TO THE SPINE MAY RESULT IN TEMPORARY OR

PERMANENT PARALYSIS OR EVEN DEATH. RESEARCH STUDIES HAVE

SHOWN THAT YOU CANNOT RELY ON THE WATER TO SLOW YOU DOWN

SUFFICIENTLY TO AVOID INJURY.

DO NOT SLIDE HEAD FIRST

INTENDED USE INSTRUCTIONS

THE ROGUE2 SLIDE IS DESIGNED AND MANUFACTURED FOR INSTALLATION

AND USE ON INGROUND SWIMMING POOLS ONLY. DO NOT INSTALL THE

ROGUE2 SLIDE ON ABOVE GROUND POOLS, HOUSEBOATS, BOAT DOCKS,

FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES OF WATER SUCH AS

LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE, AND

SUPERVISION IS ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE

RISK OF SERIOUS INJURY OR DEATH.

1. SLIDE FEET FIRST ONLY AS SHOWN IN FIGURE 1. DO NOT SLIDE HEAD FIRST

2. ONLY ONE PERSON ALLOWED ON THE SLIDE AT A TIME WITH A MAXIMUM USER

WEIGHT OF 250 LB (113 KG).

3. ADULT SUPERVISION REQUIRED AT ALL TIMES WHEN CHILDREN ARE USING THE SLIDE.

4. HOLD ONTO HANDRAILS AT ALL TIMES WHEN USING THE LADDER.

5. NO ROUGHHOUSING OR HORSEPLAY ON SLIDE.

6. DO NOT JUMP OR DIVE FROM ANY PART OF THE SLIDE.

7. FAMILIARIZE YOURSELF WITH THE SHAPE OF THE POOL BOTTOM AND THE WATER

DEPTH BEFORE YOU SLIDE. SLIDE FEET FIRST ONLY.

8. DO NOT SLIDE UNTIL ALL SUBMERGED OBSTACLES, SURFACE OBJECTS OR OTHER

SWIMMERS ARE CLEAR OF THE SLIDER’S PATHWAY.

9. DO NOT USE THE SLIDE WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS.

10. DON’T SLIDE ALONE; USE THE BUDDY SYSTEM.

11. TAKE YOUR TIME IN PREPARING TO SLIDE. MOVE FORWARD SLOWLY AND GET

YOURSELF POSITIONED PROPERLY BEFORE STARTING THE SLIDE.

12. ONLY PERSONS HEALTHY ENOUGH FOR WATER ACTIVITIES SHOULD USE THE SLIDE.

PERSONS WITH MEDICAL CONDITIONS, INCLUDING PREGNANCY, SHOULD CONSULT

THEIR DOCTOR BEFORE USING THE SLIDE. PERSONS WITH PHYSICAL DISABILITIES

SHOULD USE CAUTION AND MAY REQUIRE ASSISTANCE.

13.DO NOT USE THE SLIDE IF ANY PART OF IT BECOMES DAMAGED, WEAKENED, OR

BROKEN. HAVE THE SLIDE INSPECTED AND, IF NECESSARY, REPAIRED BY A POOL

PROFESSIONAL, WHO IS FAMILIAR WITH WATER SLIDES BEFORE USING THE SLIDE.

SEE INSTALLED SLIDES’ STRUCTURAL & INSTALLATION CHECKLIST.

READ AND FOLLOW ALL SAFETY RULES

LISTED BELOW.

MAKE SURE THAT EVERYONE WHO USES

THE ROGUE 2 KNOWS AND FOLLOWS ALL

RULES.

CHILDREN MUST BE SUPERVISED BY AN

ADULT AT ALL TIMES WHEN USING THE

SLIDE.

PROPER SLIDING POSITION

Slide users must use the sitting slide position, facing forward, feet first as shown in

Figure 1.

INSTALLED ROGUE2 STRUCTURAL & INSTALLATION CHECKLIST

After installation and prior to the first use of the ROGUE2 and periodically (see

DAILY/WEEKLY MAINTENANCE OF THE ROGUE2) thereafter the owner must:

1. INSPECT THE RUNWAY FOR VISIBLE CRACKS OR TEARS.

3. INSPECT THE LADDER FOR SHARP EDGES, PROTRUSIONS, CRACKS OR TEARS.

4. INSPECT LADDER AND PEDESTAL MOUNTING AREAS FOR LOOSE OR CORRODED

FASTENERS.

5. MEASURE THE FOLLOWING DIMENSIONS AND COMPARE WITH THE MANUFACTURER’S

PLACEMENT INSTRUCTIONS ON PAGES 5, 6, AND 7.

POOL WATER DEPTH AT THE BASE OF THE SLIDE SHOULD BE AT LEAST 3’ (914 MM) DEEP, AND AT

4’6” (1372 MM) OUT FROM SLIDE EXIT, SHOULD BE AT LEAST 4’6” (1372 MM) DEEP.

THE HEIGHT OF THE SLIDE RUNWAY EXIT ABOVE THE WATER SHOULD BE 20” (508 MM) MAXIMUM.

THE DISTANCE BETWEEN THE SLIDE CENTERLINE AND THE EDGE OF OTHER POOL EQUIPMENT

SHOULD BE AT LEAST 3’6” (1067 MM).

6. OBSERVE THE POSITION OF THE EXIT OF THE SLIDE AS SHOWN IN FIGURES 2, 3 AND 5

ON PAGES 6 AND 7.

7. READ, UNDERSTAND AND ENFORCE ALL SAFETY AND USE INSTRUCTIONS ON THE

SLIDE.

Figure 1

DAILY/WEEKLY MAINTENANCE OF THE ROGUE2

1. When hosing down the deck, hose your Rogue2 to wash away any dust, dirt or other debris,

which may have accumulated.

2. Be sure that all connections are secure. Tighten hardware if necessary.

3. All polyethylene parts require little maintenance. Hose and wipe to clean.

While cleaning slide, check and see that all nuts and bolts are tight and secure.

4. Inspect the runway for visible cracks or tears, sharp edges and protrusions.

5. Inspect all attachment points for loose or corroded fasteners.

6. Inspect all ladder tread or step-attachment points for evidence of shear, bending yield, or fatigue

in the ladder steps, rails, or attachments means. Yield is evidenced by crystallization or fine

cracking of the ladder tread and/or surface.

7. Inspect the ladder handrails for rigidity and attachment.

APPLICABLE STANDARDS AND CODES

The installation of the Rogue2 must comply with all applicable governmental and building codes.

ASSEMBLY AND INSTALLATION

All S.R. Smith Rogue2 slides are inspected prior to shipment from the factory. Proper assembly and

installation is mandatory. Improper assembly and installation voids S.R. Smith’s warranty and may affect

the safety of the user. It is the installer’s responsibility to ensure that the structural integrity of the

concrete pad prior to installation of the slide.

DRAWINGS

All drawings in this Slide Owner’s Manual (Figures 1 through 5) are for illustration purposes only and are

NOT TO SCALE.

SUBSEQUENT OWNERS

The Owner’s Manual must remain with the owner of the slide. If the owner changes, the Owner’s Manual

shall be brought to the attention of the new owner.

MANUFACTURER’S PLACEMENT INSTRUCTIONS

THE SLIDE OWNER MUST REVIEW THE MANUFACTURER’S PLACEMENT INSTRUCTIONS WITH

THE INSTALLER TO ENSURE THAT THE MANUFACTURER’S INSTALLATION REQUIREMENTS

HAVE BEEN MET.

PROPER ASSEMBLY, INSTALLATION, USE AND SUPERVISION IS ESSENTIAL FOR PROPER

OPERATION AND TO REDUCE THE RISK OF SERIOUS INJURY OR DEATH.

1. The critical dimensions for placement of the heliXTM are as shown in FIGURES 2 and 3.

A. The slide exit runway surface shall not exceed 20” (508 mm) above the water surface as shown

in FIGURE 2.

B. The slide shall be positioned so that all water flowing off the runway exit drops into the pool.

Recommended overhang is 4” (102 mm).

C. The minimum depth of water below the exit lip of the slide shall be 3’ (914 mm) and increases to

4’-6” (1372 mm) at Pt. A, which is a distance of 4’-6” (1372 mm) from the exit lip of the slide as

shown in FIGURE 2.

D. A minimum depth of 4’-6” (1372 mm) shall be maintained at a distance of 9’ (2743 mm) along the

extended centerline of the slide from Pt. A. as shown in FIGURE 2.

2. A minimum clearance area in front of the slide shall be maintained at all

times as follows:

The minimum clearance distance on either side of the extended centerline of

the slide runway shall not be less than 3’-6” (1067 mm) at a point no less than

2’-6” (762 mm) from the exit lip of the slide and extending a distance of 13’-6”

(4115 mm) in front of the slide as shown in FIGURE 3.

DECK/COPING SURFACE

3' MIN.

EXIT

RUNWAY SURFACE

PLUMBLINE

20" MAX.

WATER LEVEL

ENTRANCE

Pt.A

13'-6" MIN.

9' MIN. 4'-6"

4'-6" MIN.4'-6" MIN.

FIGURE 3

FIGURE 2

Dimensions are in feet/inches and (millimeters)

(508mm)

(1372mm)

(2743mm)

(4115mm)

(914mm)

3. SLIDE PLACEMENT INSTRUCTIONS FOR INSTALLATIONS ON POOLS WITH OTHER SLIDES

AND/OR DIVING BOARDS

A. The minimum clearance area in front of a properly installed diving board on an inground

swimming pool is a minimum distance of 3’-6” (1067 mm) on either side of the board’s centerline

as shown in FIGURE 4. Pt. C extends a minimum distance of “C” from the tip end of the board as

shown in FIGURE 4. The width distance “W” on either side of Pt. C is given in CHART 1 and

shown in FIGURE 4.

“C” DIMENSION FOR BOARD = AB + BC

“W” DIMENSION FOR BOARD = WIDTH AT PT.C

A. The minimum clearance area of a slide or diving board shall not intersect any coping or rope and

float line as shown in FIGURE 5. The minimum clearance area of a slide or diving board may

intersect each other provided that they are not used simultaneously.

CHART 1

BOARD MINIMUM CLEARANCE AREA

POOL TYPE

“C” DIMENSION

“W” DIMENSION

14’-6” (4420mm)

5’-0” (1524mm)

14’-6” (4420mm)

6’-0” (1829mm)

III

16’-6” (5029mm)

6’-0” (1829mm)

18’-6” (5639mm)

7’-6” (2286mm)

21’-0” (6401mm)

7’-6” (2286mm)

See Article 5 contained in ANSI/APSP/ICC-5 2011

STANDARD FOR RESIDENTIAL INGROUND SWIMMING

POOLS and refer to FIGURE 3 and Table 1 for Minimum

Water Envelope Dimensions AB, BC and Width at Point C.

FIGURE 5

FIGURE 4

(1067

mm)

(1067

mm)

Dimensions are in feet/inches and (millimeters)

CLEANING INSTRUCTIONS

Use nonabrasive soap and water when possible. In addition, you may safely use the

below listed products. Always try a test spot before applying to a large area.

Windex® With Ammonia Formula 409® Fantastik®

Soft Scrub® Scrubfree Tackle®

Glass Plus® Topjob® Tilex®

Always read the label instructions on any cleaner carefully before applying it to a

polyethylene surface.

AVOID HARSH CHEMICALS AND DISINFECTANTS. DO NOT USE:

Dow with Scrubbing Bubbles® Lysol® Disinfectant Ajax® Cleanser

Windex® With Vinegar White Cap® Ajax® Liquid

Serious Equipment, Serious Fun!

Product Name: Rogue2

Serial Number: ___________________ (located on label attached to slide)

Purchase Date:____________________

To register your slide and find information on the full line of S.R. Smith deck equipment

please visit www.srsmith.com.

Like us www.facebook.com/srsmithpools

Altri manuali per rogue2

Indice

Altri manuali S.R.Smith Attrezzatura di illuminazione

S.R.Smith

S.R.Smith VORTEX Manuale di istruzioni

S.R.Smith

S.R.Smith multiLift 2 Guida

S.R.Smith

S.R.Smith LM10 Manuale utente

S.R.Smith

S.R.Smith Star Series Manuale utente

S.R.Smith

S.R.Smith SWIM CLUB II FUNSLIDE Manuale utente

S.R.Smith

S.R.Smith TYPHOON Manuale di istruzioni

S.R.Smith

S.R.Smith TURBOTWISTER Manuale di istruzioni

S.R.Smith

S.R.Smith CYCLONE Manuale di istruzioni

S.R.Smith

S.R.Smith rogue2 Manuale utente

S.R.Smith

S.R.Smith pLX-PL60 Guida rapida

S.R.Smith

S.R.Smith BYOS 2 Manuale di programmazione

S.R.Smith

S.R.Smith FRONTIER II Manuale utente

S.R.Smith

S.R.Smith AQUABLAST Manuale utente

S.R.Smith

S.R.Smith heliX2 Manuale di istruzioni

S.R.Smith

S.R.Smith EDGE 6 Manuale di programmazione

S.R.Smith

S.R.Smith R Series Manuale utente

S.R.Smith

S.R.Smith ROGUE GRAND RAPIDS Manuale utente

S.R.Smith

S.R.Smith SRS-TX-30 Manuale utente

S.R.Smith

S.R.Smith PAL Series Manuale utente

S.R.Smith

S.R.Smith PT-6001 Power Tower Manuale utente

S.R.Smith

S.R.Smith SlideAway Guida all'installazione

S.R.Smith

S.R.Smith 6004 Series Manuale utente

S.R.Smith

S.R.Smith Power Tower PT-6002 Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente