Salus DIGITAL PROGRAMMABLE THERMOSTAT Manuale utente
DIGITAL PROGRAMMABLE THERMOSTAT
FOR INDIVIDUAL WEEKDAY/WEEKEND SETTING
USER'S
MANUAL
TABLE OF CONTENTS
SUMMARY......................................................................1
INTRODUCTION........................................................... 2
INSTALLATION
Removing your old thermostat.....................4
Wire labelling................................................5
Choosing a location......................................6
Connecting the thermostat...........................7
First power-up.............................................. 8
OPERATING MODES
Auto, man, econo......................................... 9
Function switch...........................................10
Filter.............................................................11
PROGRAMMING
Time and day adjustment.............................12
Pre-recorded programs................................12
Programming modification...........................13
Span adjustment........................................ 15
CHARACTERISTICS.....................................................16
1
2
AMBIENT & SET POINT
TEMPERATURE
FILTER INDICATOR
TIMER ECONO
MODE ICON
BATTERY INDICATOR
TIME & DAY
MANUAL MODE
ICON
AUTO MODE ICON
RUNNING PROGRAM
NUMBER
HEATING SYSTEM
IN OPERATION
INSTRUCTION
This thermostat can replace most common residential thermostat and is designed to be used with electric, gas or oil heating 240VAC control and relay
current up to 8 ampere.
Several useful functions and operating modes have been incorporated to adapt a variety of customer needs besides all the features associated with the
state of the art programmable thermostat, you'll find on 093.
- a 7 day timer to set the ECONO mode during a prolonged absence of user.
- a protection against freezing.
- a filter supervision.
- a programmable regulation sensibility (SPAN)
3
INSTALLATION
This thermostat has been designed for simple and quick installation requiring only a few tools.
REQUIRED MATERIAL
Hammer
Masking tape
Drill and 3/16" drill bit
Screwdriver
REMOVING YOUR OLD THERMOSTAT
CAUTION : To avoid electric shock, turn off the power of the heating system at the main power box in your home. Read the following instructions
carefully before disconnecting the wires.
1. Turn off your old thermostat.
2. Remove the cover from the old thermostat. You may have to pull extra hard.
3. Unscrew the old thermostat from the wall plate.
4. Now find the screws attaching the wall plate to the wall, and remove them. You should now be able to pull the wall plate a small distance from the
wall. Do not disconnect any wire yet, simply locate the wires.
4
Note : If your old thermostat has only two (2) wires connected to it (heating system only), simply disconnect the two wires from the wall plate, skip
over steps 1 and 2 in the Wire labelling section and go on to step 3.
WARNING : After removing the wall plate, if you find that it is mounted on a junction box (e.g. a box similar to one behind a light switch or electric
outlet), 240 volts circuit may be present and there is a danger of electric shock. Please consult a qualified electrician.
WIRE LABELLING
1. If your old thermostat wall plate has MORE THAN TWO WIRES connected to it, then you will need to label the wires (Wire identification sticker
provided). First look for LETTER near each terminal where a wire is connected. These terminals and markings may be on either side of the wall
plate.
2. Disconnect and identify each wire.
3. You may wish to tape the wires to the wall to keep them from slipping through the hole in the wall. If the hole in the wall is larger than necessary, fill it
in order to prevent hot or cold air to penetrate the thermostat. In this manner, the thermostat will behave perfectly.
5
INSTALLATION
CHOOSING A LOCATION
Note : for a new installation, choose a mounting location
about five feet (1.5 meter) above the floor in a area with
good air circulation and away from.
1. Drafts of dead air sports.
2. Air ducts.
3. Radiant heat from the sun or appliances.
4. Concealed pipes and chimneys.
Mounting the thermostat onto the wall
1. Remove completely the slide door of the thermostat.
2. Unscrew and remove the cover over the connector.
3. Mark the holes position and align the wire coming from the wall in the hole beside the connectors.
4. Drill two holes and insert the plastic anchors carefully into the holes until they are flush with the wall.
5. Fasten securely the thermostat to the wall with the two (2) screws.
6
CONNECTING THE LABELLED WIRES TO THE THERMOSTAT
1. Connect the system wires to the terminals according to the wiring diagram shown in the section "WIRING DIAGRAM"
2. Push on the wires in the wall and replace the cover over the connectors.
3. Install two (2) "AA" size batteries into the battery compartment.
4. Turn on the main switch of the system. The thermostat is ready for use.
WIRING DIAGRAM
The 093 thermostat can be used with any single stage 240 VAC heating system.
TWO (2) WIRES HEATING SYSTEM
1. Connect 240 VAC life to terminal COM
2. Connect HEATER in series with terminal NO and and 240 VAC neutral.
* Note : Heater must be capable of direct operating under 240 VAC
7
240 VAC life
+
+
+
NEUTRAL
HEATER
NC
NO
COM
INSTALLATION
FIRST POWER-UP
When power is applied for the first time, the display must show time and day as well as the ambient
temperature as follows :
If the display is different, press the RESET button. Use a fine probe such as straightened paper clip
to gently push the RESET button.
Note : Your thermostat is using two (2) "AA" size batteries to operate, it is recommended to replace
the batteries when the display is showing "BATT".
8
OPERATING MODES
The thermostat has three (3) operating modes : AUTOmatic, MANual, TIMER ECONO
AUTO : The AUTOmatic mode executes in sequence (hourly) the recorded programs.
ıPress on the AUTO button. The "PROG" icon and the running program will be displayed.
ıPressing or button display the temperature set point of the running program for five (5) seconds.
MAN : The MANual mode allows the user to bypass the programming.
ıPress on the MAN button. The icon will be displayed.
ıA first pressing on or displays the MAN temperature set point.
ıEach subsequent pressing will change the MAN temperature set point by 0.5°C
9
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Salus Termostato
Salus
Salus Optima S Manuale utente
Salus
Salus VS05 Manuale utente
Salus
Salus RT310iSPE Manuale utente
Salus
Salus BTRP230 Manuale utente
Salus
Salus RT300 Manuale utente
Salus
Salus HTR-RF(20) Manuale utente
Salus
Salus PH60 Manuale utente
Salus
Salus 091FLRF Manuale utente
Salus
Salus ERT30 Manuale utente
Salus
Salus RT520 Manuale utente
Salus
Salus RT500RF Manuale utente
Salus
Salus HTRP230V Manuale utente
Salus
Salus ST620 Manuale utente
Salus
Salus ST620 Manuale del proprietario
Salus
Salus HTRP-RF(50) Manuale utente
Salus
Salus AWRT10RF Manuale utente
Salus
Salus FC600 Manuale utente
Salus
Salus VS05 Manuale utente
Salus
Salus VS35W Manuale utente
Salus
Salus T105 RF Manuale utente
