Sam4s ellix 30 Manuale utente
OPERATOR’S Manual
All specifications are subject to change without notice
Warning - U.S.
This equipment has been tested and founded to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. In case, Operation of this equipment in a
residential area is likely to cause harmful interference to radio communications. the user
will be required to correct the interference at his own expense.
Notice - Canada
This Apparatus complies with class “A” limits for radio interference as specified in the
Canadian department of communications radio interference regulations.
Get appareil est conforme aux normes class “A” d’interference radio tel que specifier par
ministre canadien des communications dans les reglements d’interference radio.
Warning
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
FCC compliance Information(for WLAN)
This device complies with part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause undesired
operation.
Information to the user
[NOTE] This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
[IMPORTANT NOTE]
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20centimeters between the radiator and your body. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Caution
Some semiconductor devices are easily damaged by static electricity. You should turn the
printer “OFF”, before you connect or remove the cables on the rear side, in order to guard
the printer against the static electricity. If the printer is damaged by the static electricity,
you should turn the printer “OFF” and contact your dealer for assistance.
INTRODUCTION
The ELLIX 30/40 Roll Printer is designed for use with electronic instruments such as system
ECR, POS, banking equipment, computer peripheral equipment, etc.
The main features of the printer are as follows:
1. High speed printing : 220mm/s(ELLIX40), 180mm/s(ELLIX30),
52 lines per second( 12X24 Font, 220m/s)
2. Low noise thermal printing.
3. Support a variety of interfaces : USB default
ELLIX30: USB+RS-232(Serial) / USB+IEEE1284
ELLIX40: USB Only / USB+RS-232(Serial) / USB+IEEE1284 /
USB+Ethernet / USB+WLAN / USB+Bluetooth
4. Jam free (Implementation of automatic return of Cutter Jam)
5. Characters can be scaled up to 64 times compared to it’s original size.
6. The data buffer allows the unit to receive print data even during printing.
7. Bar code printing is possible by using a bar code command.
8. Different print densities can be selected by DIP switches.
9. Peripheral units drive circuit enables control of external devices such as cash drawer.
10. 2-dimantional bar code(PDF-417) and Two color printing.
Please be sure to read the instruction in this manual carefully before using ELLIX30/40.
LEGISLATION AND WEEE SYMBOL
2002/96/CE Waste Electrical and Electronic Equipment Directive on the
treatment, collection, recycling and disposal of electric and electronic devices
and their components.
The crossed dustbin symbol on the device means that it should not be disposed of with
other household wastes at the end of its working life. Instead, the device should be taken
to the waste collection centres for activation of the treatment, collection, recycling and
disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract.
This product should not be mixed with other commercial wastes for disposal
1.ELLIX 30
2.ELLIX 40
- 1 -
Table of Contents
CHAPTER 1. SETTING UP THE PRINTER..................................... 2
1-1. UNPACKING ................................................................................2
1-2. CONNECTING THE CABLES...............................................................2
1-3. CONNECTING THE COMPUTER...........................................................3
1-4. CONNECTING THE DRAWER .............................................................3
1-5. CONNECTING THE POWER SUPPLY.....................................................4
1-6. INSTALLING OR REPLACING THE PAPER ROLL........................................5
1-6-1. Partition Installation..........................................................6
1-6-2. Wall Mount Installation......................................................6
1-6-3. Paper Roll Installation .......................................................8
1-7. ADJUSTMENTS AND SETTINGS..........................................................9
1-7-1. Serial Interface(RS-232C) DIP Switch Set..........................10
1-7-2. Parallel Interface DIP Switch Set......................................11
1-8. USING THE PRINTER ...................................................................12
1-8-1. Control Panel (LED) ........................................................12
1-8-2. Feed Button ...................................................................12
1-8-3. Panel lights : LED (Color) ................................................12
1-8-4. Control Panel (LCD) ........................................................13
1-8-5. Feed Button ...................................................................13
1-8-6. Function Button..............................................................13
1-8-7. Display status : LCD........................................................13
1-8-8. Setting mode for LCD Display ..........................................14
CHAPTER 2. APPENDIX............................................................. 16
2-1.ADJUSTING THE PAPER NEAR-END SENSOR LOCATION.........................16
2-2.PRINTER HEAD CLEANING..............................................................17
2-3.ERROR STATUS AND ERROR RESOLUTION...........................................18
2-4. SPECIFICATION..........................................................................20
2-4-1. General Printer specification ............................................20
2-4-2 Paper specification...........................................................20
- 2 -
Chapter 1. Setting Up the Printer
1-1. Unpacking
Your printer box should include these items. If any items are damaged or missing, please
contact your dealer for assistance.
1-2. Connecting the Cables
You can connect up to three cables to the printer. They are all connected to the connector
panel on the back of the printer, which is shown as below:
- 3 -
1-3. Connecting the computer
You need the appropriate interface cable.
1. Plug the cable connector securely into the printer’s interface connector.
2. Tighten the screws on both sides of the cable connector.
3. Attach the other end of the cable to the computer.
1-4. Connecting the Drawer
To use the drawer, you can connect the cable
to the connector.
- 4 -
1-5. Connecting the Power Supply
Use the optional Power supply for your printer.
If the power supply’s rated voltage and your outlet’s voltage do not match, contact your
dealer for assistance. Do not plug in the power cord. Otherwise, you may damage the
power supply or the printer.
1. Make sure the printer is turned off.
2. If it is necessary to connect the interface, plug the interface connector into the
interface port on the printer.
3. Plug the DC cord connector into the power jack on the printer.
4. If it is necessary to connect the drawer, plug the drawer connector into the drawer
port on the printer.
- 5 -
1-6. Installing or Replacing the Paper Roll
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Sam4s Stampante
