Samsung SD-616E Manuale utente
Visit the Customer Support homepage of the Samsung Electronics Optical Media Solution
Division (Http://samsung-ODD.com) to find out about the latest Samsung ODD
firmwares and learn how to use them.
Main Page
Safety Precautions
Notational
Installation
While Operating
Other
Using the Drive
Using the DVD-ROM Drive
Storing and Cleaning Your Discs
Upgrading the Firmware Flash Memory
System Requirements
Introduction
Front
Rear
Troubleshooting
Solving Technical Problems
Setup
Installing the DVD-ROM Drive
Connecting the Cables
Installing the Device Driver
Setting Up the Device Driver
Specifications
Index
Warning / Caution
Warning : This symbol indicates explanations about extremely dangerous matters.
If users ignore this symbol and handle the device the wrong way, serious injury or death could
result.
Caution : This symbol indicates explanations about dangerous matters.
If users ignore this symbol and handle the device the wrong way, damage to home or property
could result.
Notational
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited
Important to read and understand at all times
Do not disassemble
Any change or modification not expressly approved by designated qualified personnel could void your
authority to operate this device.
Always make sure that the disc does not have a crack before use. If the disc has a crack (especially
around the center hole), it is recommended to make a copy immediately and use the copy instead.
When a cracked disc is used continuously, the size of the crack is likely to grow and this will eventually
result in irreparable damage to the disc.
Important to read and understand at all times.
Safety Precautions
Place the drive on a level surface.
-Failure to do so may cause the device to fall onto a hard surface,
resulting in damage or malfunction.
Do not place the drive in direct sunlight.
Avoid low
- or high-temperature environments.
Avoid high
-humidity environments.
Safety Precautions
Installation
Handle with caution to prevent damage from external shock.
Do not drop the drive, and protect it fromsevere shocks.
- It can damage the drive or cause it to malfunction.
Do not move the drive while in operation and do not attempt to open
the disc tray byforce.
Make sure to close all working programs before attempting to open the
tray and always usethe open/close button.
- Do not insert a pin into the emergency opening while in operation.
Do not use cracked, distorted or damaged discs.
- In particular, a disc with a crack on the inner tracks may break while in
use.
Safety Precautions
While Operating
Never allow food particles or foreign substances to enter the drive
casing.
To protect against the risk of fire, do ot spill such liquids as
alcohol and benzene on the drive.
Do not disassemble, attempt to repair or modify the device
without express approval as directed in the manual.
- To reduce the risk of damage, electric shock, and fire,
Safety Precautions
Other
1. Emergency eject hole. (if the compartment does not open when you press the Eject button, power off the
computer, insert a pin or unfolded paper clip in the hole and push firmly)
2. Indicator Light. (When it is green, a disc is being read.)
3. Eject button.
4. Disc compartment. (the compartment opens and closes automatically when you press the Eject button)
Design and specifications are subject to change without prior notice.
Introduction
Front
1. Two-pin digital audio output terminal for use with a sound or MPEG card supporting digital audio features.
2. Four-pin sound output terminal for use with a sound card. (refer to the sound card documentation for
further details)
3. Master/slave select terminal.
4. 40pin host IDE interface connector.
5. 4pin power terminal.
(A : +5V DC)
(B : +12V DC)
Introduction
Rear
Installing the DVD-ROM Drive
Make sure that the PC is powered off and disconnected from any power source.
If necessary, attach a horizontal bracket to both sides of the drive.
Remove the cover from a free expansion slot and install the DVD-ROM drive, as shown in the
illustration.
Setup
Connecting the Cables
Connecting the power cable
The 4-pin power cable from the internal power unit of your computer must be connected to the power
terminal on the rear of the DVD-ROM drive.
A - Cut Side
1+5V DC
2Ground
3Ground
4+12V DC
Note: An improperly connected power cable may cause trouble. Check the direction of the power connector
and the incline side of the DVD-ROM drive before connecting.
Connecting the IDE cable
Insert the IDE cable (40-pin), which is connected to the hard disk to the interface terminal.
(Place the red line of the cable close to the Pin 1.)
When using one IDE cable
Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the DVD-ROM
drive.
a : Slave Drive (Choose the SL Jumper)
b: Hard Drive
c: MainBoard
When using two IDE cable
If there is only one DVD-ROM drive, select MA (Master).
Setup
Altri manuali per SD-616E
2
Indice
Altri manuali Samsung Unità CD/CDR
Samsung
Samsung SW-252F Manuale utente
Samsung
Samsung SC-152G Manuale utente
Samsung
Samsung TS-H552B Manuale utente
Samsung
Samsung SE-T084L Manuale utente
Samsung
Samsung SM-316B Manuale utente
Samsung
Samsung TS-H552B Manuale utente
Samsung
Samsung SC-152G Manuale utente
Samsung
Samsung SM-304B Manuale utente
Samsung
Samsung SCR-3232 Manuale utente
Samsung
Samsung SC152C Manuale utente
Samsung
Samsung TS-H492A Manuale utente
Samsung
Samsung SW-208 - CD-RW Drive - IDE Manuale utente
Samsung
Samsung SW-224B Manuale utente
Samsung
Samsung SN324B Manuale utente
Samsung
Samsung SW-248B Manuale utente
Samsung
Samsung SC-152C Manuale utente
Samsung
Samsung TS-H292A Manuale utente
Samsung
Samsung SW-248B Manuale utente
Samsung
Samsung SC-140 Manuale utente
Samsung
Samsung SW-224 Manuale utente
