Samsung STP-102P Manuale utente

Warning - U.S

This equipment has been tested and found to comply with the limits for a Class A

digital device pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interface when the equipment is

operated in a commercial environment. This equipment generates uses, and can

radiate radio frequency energy and, if not installed and uses in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

Notice - Canada

This Apparatus complies with class "A" limits for radio interference as specified in

the Canadian department of communications radio interference regulations.

Introduction

The STP-102S and STP-102P Roll Printer is designed for use with electric instruments

such as system ECR, POS, banking equipment peripheral equipment, etc

The main features of the printer are as follows:

1. High speed printing

2. Low noise thermal printing.

3. RS-232 serial interface (STP-102S). Parallel interface (STP-102P).

4. The data buffer allows the unit to receive print data even during printing.

5. Different print densities can be selected by DIP switches.

Please be sure to read the instruction in this manual carefully before using your

new STP-102S and STP-102P.

NOTE

The socket-outlet shall be near the equipment and it shall be easy

accessible.

STP-102S / STP-102P

Operator's Manual

DATE: July. 2001

MANUAL REVISION 2.0

TEL : 82-31-210-5620

FAX : 82-31-210-5589

POWER ERROR FEED ON LINE

ELECTRO- MECHANI CS

Chapter 1. Unpacking

1-1. Checking the contents of the Printer

1-2. Locating the Printer

1-3. Printer Part names

1-4. Operating Control Panel

Table of Contents

Chapter 2. Connecting the cable

2-1. Connecting the AC adapter to your printer

Chapter 3. Installing the Paper Roll 10

Chapter 4. Setting the DIP Switching 11

2-2. Connecting the Printer to your computer 8

Chapter 5. Running the Self Test 13

Chapter 6. Code Table 14

Chapter 7. Functions 21

Chapter 8. Control Commands 23

APPENDIX A - Connectors

- Serial Type (STP-102S)

- Parallel Type (STP-102P)

APPENDIX B - Specification 34

Chapter 1. Unpacking

1-1. Checking the contents of the Printer.

The items illustrated below are included with your printer.

If any items are damaged or missing, please contact your

dealer for assistance.

1-2. Locating the Printer.

Avoid location in direct sunlight or excessive heat.

Avoid or storing the printer in the place subject to excessive moisture.

Do not use or store, horizontal surface for the printer. Avoid places subject to

intense vibration or shock.

Make sure that there is enough space around the printer so that it can be used easily.

Roll paper

Adaptor

Power cord

Cable

Printer

1-3. Printer Part Names

(1) Cover top

(2) Case top

(3) Case bottom

(4) Control panel

(5) Roller

(6) Power switch

(7) Interface connector (male)

(8) DC Jack

(9) Interface connector (female)

(10) Roll paper

(11) Detector switch

POWER ERROR FEED ON LINE

(1)

FEED ON LINE

(4) (3)

(2)

(5)

(10)

(11)

POWER ERROR

Control Panel

Rear View

STP-102S STP-102P

Press the FEED button once to advance paper one line. You can also press the FEED

button continuously to feed paper continuously.

Feed button is valid when ON LINE button is off.

1-4. Operating Control Panel

The control panel has two buttons and two lights.

The control panel buttons perform paper feeding and on line function.

Press the ON LINE button to ready to receive data from the computer.

ON LINE

FEED

Buttons

1) The error LED blinks fast when paper is out.

2) The error LED blinks when the Near End Sensor triggered.

The control panel lights provide information on printer conditions.

The POWER light is on when the printer power is on.

POWER(green)

ERROR(red)

Indicator lights

(6) (7) (8) (9)

Chapter 2. Connecting the Cable

2-1. Connecting the AC adapter to your printer

When the printer is used, use te optional AC adapter, AP-1611-UV for your printer.



Using an incorrect power supply may cause fire or electrical.



When connecting or disconnecting the power supply from the printer, make sure that

the power supply is not plugged into an electrical outlet ; otherwise you may damage

the power supply or the printer

1. Make sure that the printer's power switch is turned off, and that the power supply's

power cord is unplugged from the electrical outlet.

2. Check the label on the power supply to make sure that the requird voltage matches

that of your electrical outlet.

3. Plug the power supply's DC cable connector into the printer's power connector as

shown below.

4. Plug the AC adapter's power cord into an electrical outlet.

STP-102S / STP-102P

2-2. Connecting the printer to your Computer

STP-102S

You need an appropriate serial interface cable to connect your computer to the

printer's built-in interface.

1. Make sure that both the printer and computer are turned off :

then plug the cable connector securely into the printer's interface connector.

2. Tighten the screws on both sides of the cable connector.

3. Plug the other end of the cable into the computer

25 Pin Male Type

NOTE

To remove the DC cable connector grasp the connector at the arrow and

pull it straight out. Make sure that the main unit's power cord is unplugged

before you disconnect the DC cable connector.

NOTE

The printer must be turned off before installing the paper roll.

Chapter 3. Installing the Paper Roll

Use a paper roll that matches the specifications.

1. Open the printer cover and remove the used paper roll core if there is one.

2. Insert the paper roll as shown below.

3. Pull out the paper roll until the paper comes out from the top of the printer. Then

close the printer cover.

4. Turn on the Printer.

2-2. Connecting the printer to your Computer

STP-102P

You need an appropriate serial interface cable to connect your computer to the

printer's built-in interface.

1. Make sure that both the printer and computer are turned off :

then plug the cable connector securely into the printer's interface connector.

2. Tighten the screws on both sides of the cable connector.

3. Plug the other end of the cable into the computer

25 Pin Female Type

11 12

DIP switch functions

BPS

2400

4800

9600

19200

38400

57600

115200

Level

D/W1

OFF

D/W2

OFF

S/W3

OFF

Dip Switch

No.

Function

Density

Handshaking

Reserved

Language

Reserved

ON OFF

4Normal

DTR/DSR

Korean

Dark

Xon/Xoff

Engish

Chapter 4. Setting the DIP Switches

Turn off the printer while setting the DIP switch to prevent an electrical short, which can

damage the printer.

You can change your interface and printer density settings by changing the DIP switch

setting.

1. Make sure the printer is turned off.

2. There are a switch. Notice that ON is marked on each set of switches.

Use tweezers or another narrow tool to move the switches.

3. Use the following tables to set the DIP switches.

CAUTION

NOTE

Dip Switch 7 must be always set to ON condition.

13 14

Chapter 6. Code Table

The following pages show the character code tables. To find the character

corresponding to a hexadecimal number, count across the top of the table for the

For example, 4A=J.

1. Self-test printing

1) Starting the self test

To start printing the self-test on a paper roll, hold down the PAPER FEED

button and turn on the printer with the cover closed. The self-test prints the

current printer settings, which provide the following information :

- control software version

- dip switch state

2) Standby state

After printing the current printer status, the printer prints the message

"Please press the FEED BUTTON.". The LED indicator blinks and the

printer enter the test printing standby state.

Press the FEED BUTTON to start test printing.

2. Ending the self-test

After a number of lines are printed, the printer indicates the end of the

self-test by printing " ** TEST COMPLETED ** ".

If the self-test is completed, then you must reboot your printer.

Followings are the self-test results with STP-102S and STP-102P.

Chapter 5. Running the Self-test

1615

PC850 :Multilingual PC860 : Portuguese

17 18

PC865 :Nordic

PC863 :Canadian - French

19 20

Space Page

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Samsung Stampante

Samsung

Samsung ML-2545 Series Manuale utente

Samsung

Samsung CLX-3160 Series Manuale utente

Samsung

Samsung ML-1200 Series Istruzioni operative

Samsung

Samsung ML 1740 - B/W Laser Printer Manuale utente

Samsung

Samsung CLP CLP-550 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Samsung

Samsung ML 1630 - B/W Laser Printer Manuale utente

Samsung

Samsung ML-D1630A Manuale utente

Samsung

Samsung QL 6100 Manuale utente

Samsung

Samsung ProXpress C3010 Series Manuale utente

Samsung

Samsung ML-1700 Series Manuale utente

Samsung

Samsung CLP-320 Series Manuale di istruzioni

Samsung

Samsung ML-3750ND Manuale utente

Samsung

Samsung Xpress M3065 Series Manuale utente

Samsung

Samsung ML 7000 Manuale utente

Samsung

Samsung CLX-4195 Series Manuale utente

Samsung

Samsung CLP 610ND - Color Laser Printer Manuale utente

Samsung

Samsung Xpress M268 Series Manuale utente

Samsung

Samsung MFP SCX-6345N Guida utente

Samsung

Samsung ML-2850D Manuale utente

Samsung

Samsung ML-3560 Series Istruzioni di installazione e manutenzione

Samsung

Samsung SPP 2020 - Photo Printer - 20 Sheets Manuale utente

Samsung

Samsung ML-1430 Manuale utente

Samsung

Samsung ML-5050G Series Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente

IRA3D

IRA3D POETRY4 Manuale utente