Sanus Systems PFFP Manuale utente

"Tl

....

::J

()

:::Y

:JJ

(f)

::J

(j)

....

::J

c....

::J

(f)

THE

UNION

FORM

AND

FUNCTION

International Assembly Instructions for model PFFP

SAN

SYSTE

IVI

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 7.05.05

Customer Service: (800) 359-5520 •(651) 484-7988 •fax (651) 636-0367

Customer Service Europe:

(0)20 5708938 •fax

(0)20 5708989

See complementary Sanus products at www.sanus.com

SANUS

SVSTEIVIS

THE

UNION

FORM

AND

FUNCTION

Assembly Instructions for Sanus Systems Platinum Furniture Model: PFFP

bxI

c x I

axi

~--

Thank you for choosing Sanus Systems Platinum Furniture. The PFFP

designed to support a30" to 50" flat panel

television

130 lbs.

you have any questions regarding this or any other Sanus Systems product, please contact

us at 800.359.5520 or visit

at www.sanus.com. Our customer service representatives can assist you quickly with any

issues regarding assembly or missing parts. Check carefully to make sure none of the parts are missing or defective.

Never use defective parts. Replacement parts for products purchased from an authorized dealer will be shipped

directly

you. Please call Sanus Systems before returning products to the retail store where you purchased them.

Required Tools: Wrench or Socket Set, Phillips Screw Driver

Parts: Not shown at actual size

dxIe x I

£Xl

gxI

hx2

ixIjxI

kxI

1xI

fiX

Hardware: All hardware shown as actual size

.-s

nx2

ox2

px2

-=D

qx4

r x 2

sx2

@@0

tx6

ux4

vx2

wx2

Bm()

-0

xx4

yx4

zx4

aa x4

----0

cc x4 dd x 4 ee x4

ffx

4gg

mmx4

llx4

Step

Secure Pillar to Base

Attach the Pillar

(t)

to the Base (a) by placing each M12 x

Bolt (p) through an M12 Washer (w), each M8 x35 Bolt

through an M8 Washer (t). Then thread each Bolt

through the Base and into the Pillar as shown in Diagram

lao

The M12

x40 Bolts should be threaded into the front two holes

the Pillar, while the M8 x35 Bolts should be threaded into the back

two holes

the Pillar. Tighten the M

x40 Bolts with awrench, and tighten the M8 x

Bolts with aPhillips screw driver.

Proceed to insert two M6 x20 Bolts (n) into the holes on the back

the Pillar as seen

Diagram lb. Tighten the M6 x20

Bolts with aPhillips screw driver.

Detailed View A

Diagram

Step

Shelf Bracket Assembly

Detailed View B

Required Hardware for Step 1

(2)

Ml2

x40

(2) M8 x

(2)

x20

.-B

(2)M12Washer @

(2) M8 Washer @

Thread an M8 Allen Bolt (q) through aSpring Washer (u), an M8 Washer (t), the Shelf Bracket 0), and into the Shelf Plate

(i). See Diagram 2for the proper assembly

these parts. Loosely tighten the M8 Allen Bolt into the Shelf Plate with an

Allen Key (nn). Leave approximately a

118"

gap between the ShelfBracket and the ShelfPlate for Step 4.

Diagram 2

Required Hardware for Step 2

(2) M8 Allen Bolt -=D

(2) Spring Washer

(2) M8 Washer @

Step

3: Wall Bracket

Assembly

Thread an M8 Allen Bolt (q) through aSpring Washer (u), an M8 Washer (t), through the middle hole

the Wall Bracket

(b), and into the Wall Plate (g) as seen in Diagram

Loosely tighten the M8 Allen Bolt into the Wall Plate with an Allen

Key (nn). Leave approximately aliS" gap between the Wall Bracket and the Wall Plate for Step 5.

Diagram 3

Required

Hardware

for Step 3

(2) M8 Allen Bolt

-=0

(2) Spring Washer

(2)

Washer @

Step

Add

Shelf

Bracket

Pillar

Add the ShelfBracket Assembly to the Pillar

(f)

by sliding it down from the top to the desired position on the Pillar. Make

sure the ShelfPlate (i) fits into the channel in the Pillar. See the Top View

Diagram 4for assistance. Once you have the

Shelf

Bracket Assembly in place, proceed to tighten the M8 Allen Bolts (q) with an Allen Key (nn) so the Shelf Bracket

Assembly is firmly in place.

Note: Make Sure The M8 Allen Bolts Are Tight!

Top View

Diagram 4

ShelfBracket

Assembly

Step

Add Wall Bracket

Slide the Wall Bracket Assembly down into place on the Pillar (f). Make sure the Wall Plate (g)

fits

into the channel in the Pillar as seen

in the Top View

Diagram 5. Once the Wall Bracket Assembly

the desired position, tighten the M8 Allen Bolts (q) with an Allen

Key (nn) so the Wall Bracket Assembly

attached to the Pillar. Attach the Wall Bracket Spacers (h) to the Wall Bracket (b) by sliding

the Wall Bracket Spacers from the side so the plastic tabs into the correct oval holes on the Wall Bracket. See the Top View

Diagram

You

may have to loosen the M8 Bolts

the Wall Bracket to have enough space

fit

the Wall Bracket Spacers in between the Wall

Bracket and the Pillar.

Note: Make Sure The M8 Allen Bolts Are Tight!

Top View

Step

Add the Glass Shelf

Take the Glass ShelfWasher (k) and insert it onto the Glass Shelf (c). Make sure the holes in the Glass ShelfWasher and the Glass Shelf

are aligned. Slide the Glass Shelfassembly into the Shelf Bracket 0). Thread each 1/4-20 Allen Bolt (r) down through aPlastic Washer

(v), the Glass Shelfand into the Shelf Bracket assembly. Tighten the 1/4-20 Allen Bolts firmly so the Glass Shelf is secured to the Shelf

Bracket. See Detailed View A

Diagram 6for assistance.

Add the Top Cap (m)

the top

the Pillar

(f)

by lining up the two plastic dowels

the bottom

the Top Cap with the corresponding

pattern on the top

the Pillar as seen

Detailed View B

Diagram

Press down firmly on the Top Cap

make sure it is in place.

Place the Shelf Bracket Cap (I) over the Shelf Bracket (j) so it hides the M8 Allen Bolt (q). See Detailed View A

Diagram 6below.

Diagram 6Detailed View B

Step

Mounting Monitor Brackets to atelevision with aflat back

First, determine the diameter

the Bolt (x,y,z,aa) your

requires by hand threading them into the threaded insert on the back

the

TV.

you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram

below. You will thread the Bolt through the appropriate Lock Washer (ff,gg,hh,ii), aWasher (jj,kk), the Monitor Bracket (d,e), and finally

into the TV.

Make

sure the

Monitor

Brackets are vertically centered and level with each other. See the appropriate Diagram below.

Note: For televisions with acurved back, or an obstruction near the threaded insert see Step

M4 Diameter Bolt M6 Diameter Bolt

Step

Mounting Monitor Brackets to atelevision with acurved back or an obstruction near the threaded insert

First, determine the diameter

the Bolt (bb,cc,dd,ee) your TV requires by hand threading them into the threaded insert on the back

the

TV.

If you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram

below.

You

will thread the Bolt through the appropriate Lock Washer (ff,gg,hh,ii), aWasher (jj,kk), the Monitor Bracket (d,e), aWasher

(jj -

M41M5

only), aSpacer (lI,mm) and finally into the

TV.

Make sure the Monitor Brackets are vertically centered and level with each

other. See the appropriate Diagram below.

M4 Diameter Bolt M6 Diameter Bolt

Step 9: Hang TV

To hang the

onto the Wall Bracket (b) first

hook

the Monitor Brackets (d,e) over the top

the Wall Bracket, then let the

bottom

the Monitor Brackets rotate in under the bottom

the Wall Bracket as shown in the Detailed View

Diagram 9.

Detailed

View

Diagram

Step 10:

Add

Safety Bolts

Insert the Safety Bolts (s) into the threaded holes in the bottom

the Monitor Brackets (d,e) and tighten them with the Al-

len Key (nn) so that they sit behind the bottom tab on the Wall Bracket (b) as shown in the Detailed View

Diagram 10.

Finally set the tension

the knobs on the Monitor Brackets and you are free to adjust your new flat panel

TV.

See Diagram

10 below.

Diagram

Detailed

View

Bottom Tab on the

Wall Bracket

Required

Hardware

for

Step

(2) Safety Bolts

Altri manuali per PFFP

Altri manuali Sanus Systems Rack e supporto

Sanus Systems

Sanus Systems VM2 Manuale utente

Sanus Systems

Sanus Systems VM400 Manuale utente

Sanus Systems

Sanus Systems VMUC1 Manuale utente

Sanus Systems

Sanus Systems VMSA Manuale utente

Sanus Systems

Sanus Systems VMPL50 Manuale utente

Sanus Systems

Sanus Systems New VisionMount VMA201 Manuale utente

Sanus Systems

Sanus Systems BF16 Manuale utente

Sanus Systems

Sanus Systems Wall Mount LL22 Manuale utente

Sanus Systems

Sanus Systems VMPL50 Manuale utente

Sanus Systems

Sanus Systems VisionMount VMCA7 Manuale utente

Sanus Systems

Sanus Systems Natural Foundations NF18 Manuale utente

Sanus Systems

Sanus Systems WMS3 Manuale utente

Sanus Systems

Sanus Systems VISIONMOUNT VMCA8 Manuale utente

Sanus Systems

Sanus Systems NF18B Manuale utente

Sanus Systems

Sanus Systems New Foundations 100 Series Manuale utente

Sanus Systems

Sanus Systems Euro Series Manuale utente

Sanus Systems

Sanus Systems WMS3 Manuale utente

Sanus Systems

Sanus Systems EFSat Manuale utente

Sanus Systems

Sanus Systems SD103 Manuale utente

Sanus Systems

Sanus Systems VisionMount MF202 Manuale utente

Sanus Systems

Sanus Systems Sanus VisionMount LC1A Manuale utente

Sanus Systems

Sanus Systems EFB Manuale utente

Sanus Systems

Sanus Systems WMS2 Manuale utente

Sanus Systems

Sanus Systems VisionMount MF203 Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente