Sanus Systems VMUC1 Manuale utente
ESPAÑOL DEUTSCH FRANÇAIS ITALIANO PYCCKO
Spanish German French Italian Russian Japanese Mandarin
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 7.05.05
Customer Service: (800) 359-5520 • (651) 484-7988 • fax (651) 636-0367
Customer Service Europe: 31 (0)20 5708938 • fax 31 (0)20 5708989
See complementary Sanus products at www.sanus.com
中文
ENGLISH
International Assembly Instructions for model VMUC1
ENGLISH
Assembly Instructions for Model: VMUC1
Thank you for choosing a Sanus Systems Vision Mount under cabinet mount. The
VMUC1 is designed to hold up to a 17 inch flat panel LCD weighing up to 18
lbs.
Safety Warning: If you do not understand these directions, or have any doubts
about the safety of the installation, please call a qualified contractor or contact
Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there
are no missing or defective parts. Our customer service representatives can quickly
assist you with installation questions and missing or damaged parts. Replacement
parts for products purchased through authorized dealers will be shipped directly to
you. Never use defective parts. Improper installation may cause damage or serious
injury. Do not use this product for any purpose that is not explicitly specified by
Sanus Systems. Sanus Systems can not be liable for damage or injury caused by in-
correct mounting, incorrect assembly, or incorrect use. Please call Sanus Systems
before returning products to the point of purchase.
Required Tools: Phillips screw driver, drill, 1/4 inch drill bit
Supplied Parts and Hardware: Some parts not shown as actual size*
(3) T - Nuts - b (3) 10-24 x 5/8 Bolt - c
(1) Mount Assembly - a
(4) M4 x 10 mm Bolt - d (4) M4 x 20 mm Bolt - e
(4) .5 inch Spacer - f
(4) Cable Tie - g (1) Allen Key - h
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 12.30.05
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
ENGLISH
1.89 1.89
3.28
Step 1: Remove Cover
Using a Phillips screw driver loosen the two flat head bolts from the cover and slide it down and away from the mounting plate. See
Diagram 1 for assistance. You will re-install the cover once cable management is complete.
Diagram 1
a
mounting plate
cover flat head bolts
Step 2: Prepare Mounting Surface
Use the base of the Mount Assembly
(a) as a template to mark three holes
in the cabinet in the desired location.
Drill three 1/4 inch holes at the marked
locations.
See the dimensional drawing on the
right for assistance.
See page 9 for a 1:1 scaled version of
the dimensional drawing.
Dimensional Drawing
ENGLISH
Step 3: Secure Mount Assembly to cabinet
Using the 10-24 x 5/8 Bolts (c) and the T - Nuts (b) secure the Mount Assembly to the cabinet. See Diagram 3 for assistance. Note: Make
sure the spikes on the T - Nuts is facing toward the cabinet.
Diagram 3
Detailed View
b
cabinet
c spike
Step 4: Attach flat panel display to mounting plate
Make sure no power is supplied to the display before mounting the display!
Warning: Watch for pinch points. Do not put your fingers or cables between movable parts.
Once the Mount Assembly (a) is secured to the cabinet, align the appropriate slots in the mounting plate with the four mounting holes of
your LCD display. Use either four M4 x 10 mm Bolts (d) or four M4 x 20 mm Bolts (e) with four .5 inch Spacers (f). Diagram 4a below
shows the M4 x 10 mm Bolts being used. Diagram 4b on the next page shows the M4 x 20 mm Bolts with the .5 inch Spacers.
Detailed View
Diagram 4a
LCD panel
d
mounting plate
ENGLISH
Step 4 (cont)
The .5 inch Spacers (f) should only be used if there is an obstruction or the hole pattern is physically recessed on the back of the LCD
panel. See Diagram 4b for assistance.
Detailed View Diagram 4b
e
mounting plate
f
LCD Panel
Step 5: Adjusting the screen height.
Using a Phillips screw driver, slightly loosen the Bolts (d,e) that secure the LCD panel to the mounting plate. Adjust the LCD panel to
the desired height. Tighten the Bolts (d,e) to secure the LCD panel to the mounting plate. See Diagram 5 for assistance.
Diagram 5
d,e
mounting plate
ENGLISH
Step 6: Adjust tension of Mount Assembly
The tension of the Mount Assembly (a) can be adjusted by simply tightening or loosening the tension bolt labeled in Diagram 6 with the
provided Allen Key (h).
Diagram 6 Detailed View
tension bolt
Step 7: Remove Cable Cover
Using a Phillips screw driver, loosen the screw in the center of the cable cover and remove cover. See Diagram 7 for assistance. Note:
You will re-install the cable cover once cable management is completed.
Diagram 7 Detailed View
cable cover
screw
ENGLISH
Step 8: Cable Management (±35° swivel)
Swivel the Mount Assembly (a) 35° either left or right. You will run the cables in the opposite direction. You can attach the Cable Ties
(g) in locations marked in Diagram 8 below.
Diagram 8
a
cable path
cable tie
holder
ENGLISH
Step 9: Remove Degree Stop
Using provided Allen Wrench (h), remove the 35 degree stop. See Diagram 9 for assistance.
Diagram 9
35 degree stop
ENGLISH
Step 10: Cable management (±110°)
Swivel the Mount Assembly (a) 110° either left or right. You will run the cables in the opposite direction. Cables must be wrapped a
complete 360° inside the base of the Mount Assembly. You can attach the Cable Ties (g) in locations marked in Diagram 8 below.
Diagram 10
cable tie
holder
a cable path
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 12.30.05
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Indice
Lingue:
Altri manuali Sanus Systems Rack e supporto
Sanus Systems
Sanus Systems NF18B Manuale utente
Sanus Systems
Sanus Systems VM2 Manuale utente
Sanus Systems
Sanus Systems MF110 Manuale utente
Sanus Systems
Sanus Systems WMS3 Manuale utente
Sanus Systems
Sanus Systems EFB Manuale utente
Sanus Systems
Sanus Systems Monitor Mount VMTV Manuale utente
Sanus Systems
Sanus Systems VMCM1 Manuale utente
Sanus Systems
Sanus Systems VMPR1 Manuale utente
Sanus Systems
Sanus Systems New VisionMount VMA201 Manuale utente
Sanus Systems
Sanus Systems Wall Mount LL22 Manuale utente
Sanus Systems
Sanus Systems WMS5 Manuale utente
Sanus Systems
Sanus Systems Sanus VisionMount LC1A Manuale utente
Sanus Systems
Sanus Systems VisionMount VMPL2 Manuale utente
Sanus Systems
Sanus Systems PFV59S Guida all'installazione
Sanus Systems
Sanus Systems VMCA9 Manuale utente
Sanus Systems
Sanus Systems PFV60-B1 Manuale utente
Sanus Systems
Sanus Systems VMPL50 Manuale utente
Sanus Systems
Sanus Systems VisionMount MF203 Manuale utente
Sanus Systems
Sanus Systems VM2 Manuale utente
Sanus Systems
Sanus Systems FM37 Manuale utente
