Sanus BXT3 Manuale utente

THANK YOU FOR CHOOSING SANUS

THE #1 TV MOUNT BRAND IN THE US.

BXT

Instruction Manual

WE’RE HERE TO HELP

Our US-based install experts

are standing by to help.

Call us at:

800-359-5520

Or, chat at:

SANUS.com/chatSP

Get it right the ﬁrst time.

HeightFinder™ shows you

where to drill.

Check it out at:

SANUS.com/1172

Want to watch a video that

shows how easy this DIY

project will be?

Watch it now at:

SANUS.com/2689

Recommended placement

175 lbs.

(79.3 kg)

110 lbs.

(49.8 kg)

IMPORTANT SAFETY INSTRUCTIONS – PLEASE READ MANUAL PRIOR TO USE – SAVE THESE INSTRUCTIONS

Please read through these instructions completely to be sure you’re comfortable with this easy install process.

Check your TV owner’s manual to see if there are any special requirements for mounting your TV.

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact Customer Service.

CAUTION: Avoid potential personal injuries and property damage!

●This product is designed ONLY to be installed into wood studs, solid concrete or concrete block, or steel studs.

—DO NOT INSTALL INTO DRYWALL ALONE — DRYWALL ALONE WILL NOT HOLD THE WEIGHT OF YOUR TV.

●This product is designed for INDOOR USE ONLY.

●The wall must be capable of supporting ﬁve times the weight of the TV and mount combined.

●Do not use this product for any purpose not explicitly speciﬁed by manufacturer.

●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.

TV Weight Limit

(including accessories)

DO NOT EXCEED

If your TV (plus accessories)

weighs MORE, this mount is

NOT compatible.

Visit SANUS.com or call

customer service to ﬁnd a

compatible mount.

For wood stud and

Solid Concrete or

Concrete Block Walls

For Steel Stud Walls

Call Customer Service

Tools Needed

Wall

Construction

ONLY install on

these acceptable

wall types. Drywall

alone will

NOT hold

the weight

of your TV.

Unsure

wood studs Solid concrete

or concrete

block

ACCEPTABLE ACCEPTABLE

Wood Stud Install

Concrete Install

Awl

Pencil Level Tape

Stud

Finder

ScrewdriverTape

Measure

7/32 in.

(5.5 mm)

Wood

Drill Bit

Electric

Drill

Hammer

1/2 in.

(13 mm)

Socket

Wrench

Drill Bit

3/8 in.

(10 mm)

Concrete

CAUTION:

DO NOT

install in

drywall alone

steel studs

Steel stud kit #SSMK1 is

required [NOT INCLUDED].

See PAGE 14 for details.

Steel Stud Install

Awl

Stud

Finder

1/2 in.

(13 mm)

Steel

Drill Bit

ACCEPTABLE

M8 x 25mm M8 x 50mm

M8 x 45mm

M8 x 35mm

M8 x 16mm

M8 x 20mm

2.5mm

22mm

M6 x 12mm M6 x 35mm

5mm

5⁄16 in. x 2 ¾ in.

Fischer UX10 x 60R

NOTE: Not all hardware included will be used.

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to

your dealer; contact Customer Service. Never use damaged parts!

Supplied Parts and Hardware

Parts and Hardware for STEP 1

TV Screws

(qty. 4 each) [Only one size ﬁts your TV] Washers

(qty. 4 each) Spacers [If necessary]

(qty. 4 each)

030201

M6/M8 M6/M8

M8 x 25mm M8 x 50mm

M8 x 45mm

M8 x 35mm

M8 x 16mm

M8 x 20mm

2.5mm

22mm

M6 x 12mm M6 x 35mm

5mm

5⁄16 in. x 2 ¾ in.

Fischer UX10 x 60R

Parts for STEP 1 [CONTINUED] Parts and Hardware for STEP 2 Adjustments

Left TV Bracket

Right TV Bracket

(qty. 1)

CAUTION:

Avoid potential personal injury!

The TV brackets contain

potential pinch points during

operation. Keep fingers away

from pinch points when

retracting your TV. (arrows)

Concrete Anchors

For concrete installations ONLY

CAUTION: Do not use in drywall or wood

Lag Bolts

Hex Key

3/16 in.

Wall Plate

(qty. 1)

(qty. 8)

(qty. 1)

STEP 1 Attach Brackets to TV

Inset Holes Cables

Only one screw size ﬁts your TV.

M6 M8 • Flat Back TV

[TV brackets 04 /05

lay ﬂat on your TV]

NO SPACER SPACER NEEDED

• Flat Back TV with

Extra Space Needed

[for deep inset holes

or cable interference]

• Rounded or

Irregular Back TV

[TV brackets 04 /05 NOT

resting ﬂat on your TV]

A B

Use short TV screws 01 .

Spacers 03 not needed. Use long TV screws 01 and spacers 03 to

create extra space between the TV and TV bracket.

CAUTION: Verify adequate thread engagement with your

screw 01 , washer 02 , spacer 03 combination AND TV bracket 04 /05 .

—Too short will not hold your TV. —Too long will damage your TV.

Too Short

Too Long

Correct

1.2 Select TV Screw Length and Spacers1.1 Select TV Screw Diameter

1.3 Attach TV Brackets to Your TV

NO SPACER

SPACER NEEDED

03 02

Center TV brackets 04 and 05 over your TV's hole pattern and attach using screw combination

Aor Byou selected for your TV.

NOTE: The tilt tension knob Ton TV brackets 04 and 05 should be oriented to the outside edges.

Adjust the release tabs Rto the bottom of the TV.

If your TV included

inset spacers or wall

mount adapters, see

Troubleshooting (PAGE 22).

For TV VESA width greater than 700 mm, extend the wall plate to accommodate the TV brackets.

CAUTION: Avoid potential personal injuries and property damage!

FOR EXTENDED WALL PLATES:

You MUST install 2 lag bolts 07 into the center (top and bottom)

of wall plate 06 , then a minimum of 16 in. (406 mm) out from center,

for a minimum of 6 lag bolts total.

> 700mm (27 1/2 in.)

Min. 16 in.

(406 mm)

Min. 16 in.

(406 mm)

STEP 2 Attach Wall Plate to Wall

04 05

NOTE:

If needed,

loosen the nuts

shown to help

slide open.

WARNING: Avoid potential personal injuries!

These areas could be pinch points when sliding back together.

STEP 2A Wood Stud Installation

Locate studs. Verify the center of the stud(s) using an awl,

a thin nail, or an edge to edge stud finder.

1Max.

5/8 in. (16 mm)

Min.

16 in. (406 mm)

Place wall plate 06 at your desired height, over your stud center lines.

Level the wall plate 06 and mark the four (or six) hole locations.

CAUTION: Avoid potential personal injury or property damage!

●Drywall covering the wall must not exceed 5/8 in. (16 mm)

●Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm)

●Minimum horizontal space between fasteners: 16 in. (406 mm)

●Stud centers must be verified

CAUTION: FOR EXTENDED WALL PLATES:

You MUST install 2 lag bolts 07 into the center (top and bottom)

of wall plate 06 , then a minimum of 16 in. (406 mm) out from center,

for a minimum of 6 lag bolts total.

Indice

Altri manuali Sanus Rack e supporto

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente