Satel MAGENTA Manuale utente
MAGENTA
DIGITAL GLASS-BREAK DETECTOR
magenta_en 06/15
The MAGENTA detector enables detection of plate, tempered or laminated glass breaking.
This manual applies to the detector with electronics version 1.1 (or newer).
1. Features
Advanced dual path signal analysis.
Stepless regulation of detection sensitivity.
Supply voltage control.
LED indicator.
Tamper protection in 2 ways – cover removal and tearing enclosure from the wall.
2. Description
The detector will report the alarm when a low frequency sound (impact) followed by a high
frequency sound (glass-break) are registered. The high-frequency channel is analyzed for
four seconds from receiving the low-frequency sound wave, caused by the impact.
Supply voltage control
In the event of a prolonged voltage drop below 9 V (±5%), the
detector will signal a trouble. The trouble is indicated by the
activation of alarm relay and the steady light of LED indicator.
The trouble signaling will continue as long as the trouble
persists.
Electronics board
terminals:
+12V - power input,
COM - common ground,
TMP - tamper output (NC),
NC - alarm output (NC).
tamper contact.
red color LED to indicate:
detection of low-frequency sound – ON for 0.5 seconds,
alarm – ON for 2 seconds,
test mode – short flash every 3 seconds,
low supply voltage – ON.
detector configuration pins:
TEST – enabling/disabling the test mode. In the test mode,
the detector reports an alarm when it detects a high
frequency sound. The INDIGO TESTER is
recommended to test the detector. The test mode is
enabled when the jumper is set in ON position (Fig. 2).
2 MAGENTA SATEL
LED – enabling/disabling the LED indicator. The LED indicator is enabled when the
jumper is set in ON position (Fig. 3).
potentiometer for the adjustment of detection sensitivity (Fig. 4).
3. Installation
Curtains, drapes, furniture upholstery, acoustic tiles, etc. absorb the sound and
adversely affect the detection range.
Disconnect power before making any electrical connections.
The detector should be installed indoors, in spaces with normal air humidity. The protected
glass surfaces must be within the detector operating range.
1. Open the detector enclosure (Fig. 5).
2. Make the opening in the enclosure base for the cable.
SATEL MAGENTA 3
3. Pass the cable through the prepared opening.
4. Using wall plugs (screw anchors) and screws, fasten the enclosure base to the mounting
surface (Fig. 7). Wall plugs (screw anchors) and screws are included in the detector
delivery set.
5. Connect the wires to the corresponding terminals on the electronics board.
6. Configure the detector using jumpers and the potentiometer.
7. Close the detector enclosure.
4. Specifications
Supply voltage ................................................................................................... 12 V DC ±15%
Standby current consumption ............................................................................................5 mA
Maximum current consumption........................................................................................10 mA
Relay contacts rated load (resistive)............................................................... 40 mA / 16 V DC
Alarm signaling time ............................................................................................................. 2 s
Detection range .......................................................................................................... up to 6 m
Environmental class according to EN50130-5 ......................................................................... II
Operating temperature range..................................................................................-10...+55 °C
Enclosure dimensions....................................................................................26 x 112 x 29 mm
Weight................................................................................................................................. 40 g
The declaration of conformity may be consulted at www.satel.eu/ce
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. 58 320 94 00
www.satel.eu
Indice
Altri manuali Satel Sensore di sicurezza
Satel
Satel AXD-200-DG Manuale utente
Satel
Satel SLIM-DUAL-PRO Manuale utente
Satel
Satel GRAPHITE Manuale utente
Satel
Satel AOD-200 Manuale utente
Satel
Satel PDB-100 Manuale utente
Satel
Satel OPAL Manuale utente
Satel
Satel APD-100 Manuale utente
Satel
Satel AMD-102 Manuale utente
Satel
Satel AGD-100 Manuale utente
Satel
Satel INDIGO Manuale utente
Satel
Satel SLIM-DUAL-LUNA-PET Manuale utente
Satel
Satel TESTER INDIGO Manuale utente
Satel
Satel CD-2 Manuale utente
Satel
Satel AGD-100-BR Manuale utente
Satel
Satel AOCD-250 Manuale utente
Satel
Satel AMD-103 Manuale utente
Satel
Satel A D-200 Series Manuale utente
Satel
Satel AQUA PRO Manuale utente
Satel
Satel COBALT Manuale utente
Satel
Satel GRAPHITE Manuale utente
