Industrial Managed Gigabit EthernetSwitches
RPT-2008G-X1/RPT-2008GP-X1
RPT-2008G-4F-X1/RPT-2008GP-4F-X1
Version 1.2
Updated in November,2016
Inside the package you will find the followingitems:
■Industrial Managed Gigabit Ethernet Switch x 1
■4-Pin 5.08mm Lockable TerminalBlock (Already mounted to the device) x 1
■5-Pin 5.08mm Lockable TerminalBlock (Already mounted to the device) x 1
■DIN-Rail Kit (Already mounted to the device) x 1
■Protective caps for all SFP and PoE ports (Depend on purchasedmodel)
■Installation Guide with Warranty Card x 1
RPT-2008G-4F-X1
RPT-2008GP-4F-X1
RPT-2008G-X1
RPT-2008GP-X1
1. Reset button
2. RingLED
3. RUNLED
4. Ring Master LED
5. Alarm LED
6. SFP Ports LEDs
7. PWR1LED
8. PWR2LED
9. PoE LEDs
10. 1000 BASE-X SFP Slots
11. 10/100/1000 BASE-T(X) RJ-45 Ports and/or
10/100/1000 BASE-T(X) PoE RJ-45Ports
Never install or work on electrical or cabling during periods of lightning activity.
Never connect or disconnect power when hazardous gases are present.
Warning:HotSurface Do Not Touch.RESTRICTEDACCESS AREA: The equipment
should only be installed in a Restricted AccessArea.
Caution: CLASS 1 LASER PRODUCT. Do not stare into the laser!
I n d o o r
This equipment should be installed indoorand not connect directlywithequipment
installed outdoor.
7
8
9
7 2
8 4 7 2
8 4
9 6
11 1110
3
53
5
1 1
1. Grounding Screw
2. DIP Switches
3. RS-232 Console
4. Relay Output 1 with current carrying
capacity of 1A@24 VDC (Normal Open)
5. Relay Output 2 with current carrying
capacity of 1A@24 VDC (Normal Open)
6. Frame Ground
7. Terminal for Power 1
8. Terminal for Power 2
1
1
2
2
1
2
3
4
5
6
7
8
3. You can then choose whether to plug in the other
peripheral ports at this point or do it later depending
on the actual location of the device or level of
comfort for performing such operation.
Remeber to plug in the protective caps for the
unused SFP and PoE ports.
4. Once the plate has been firmly put in place, proceed
to mount the whole device as shown in (Fig.
3).Proceed to (Fig. 4) if you want to remove the
device from DIN-Rail.
5. Next we can then proceed to connect the device to
the LAN (switch or PC, depending on the case), take
care on using the RJ-45 connector; after this we can
then proceed to the device’s settings
1. If you have purchased the wall mount kit,
proceed to place the screws on the back
of the device as show in (Fig. 1).
2. Although internal grounding has been
done inside, in order to ensure overall
maximum performance and protect your
device, it is still strongly advised to ground
the device properly; hazardous ESD can
come into contact and damage your
equipment. On the power terminal block,
there is a terminal for Frame Ground, you
can choose whether to connect it to the
grounding or you may opt to connect to
the grounding screw next to the terminal
block ( the one chosen should be connect-
ed at all times ) (Fig. 2)
is disconnected
■The opening to the sides are for the device’s heat
dissipation please never obstruct or cover them
with any objects or try to insert them through it.
■This switch’s factory IP by default is 10.0.50.1 you
can access the device by its Web UI once it is
connected to a physical network (or using
Management Utility, for more information on
Management Utility, please refer to its manual).
Please be aware that the PC needed for this
procedure needs to be in the same subnet, or
you may refer yourself to the device User’s
Manual.
