Schlage Ease S2 Manuale utente
Lever spigot
Mounting screws (3)
Two lengths provided
Key
Cover screws (4)
Also includes (not shown):
a) Strike plate & screws
b) 4 x AA Alkaline batteries
Slide the spindle hole position to suit 60mm
(2-3/8”) or 70mm (2-3/4”) backset
Ø54mm
(2-1/8”)
Ø60mm
(2-3/8”)
Ø60mm
(2-3/8”)
Ø70mm
(2-3/4”)
Ø70mm
(2-3/4”)
1. Install latch on the door, ensuring the pin
side of the latch is facing away from the
door jamb/frame.
Pin side of the latch
NOTE: Cable must
go through door hole
above the latch.
3. Position the inside mounting plate to sit
flush on the door, ensuring the cable and
spindle go through the holes in the mounting
plate. Secure both assemblies using 8/32
screws provided. Make sure the exterior
assembly is vertically aligned. If you added
the cross bolt, securely tighten the post to
the exterior Ease unit with the additional
screw provided.
Optional
screw
4. Attach cable assembly to the interior
assembly PCB by lining up notches on
top of cable connector to slots on PCB
connector. Press connector in firmly until
completely connected.
This hole is for the
optional cross bolt
provided for
stabilising your lock.
If you drilled a hole,
securely tighten the
post before mounting
on the door.
Ensure the spindle
is square.
7. Insert the cylinder into the lever.
8. Using a flat head screwdriver, ensure the
turnplate is set vertical.
Turnplate
6. Install batteries and battery cover.
5. Install interior assembly on inside mounting
plate. Secure using 4 screws through the
interior assembly onto the mounting plate.
9. Insert the key into the cylinder and ensure
the key is horizontal. Check handing to
ensure the lever is pointing towards the
hinges. Push the lever onto the lever
spigot until it clicks into place.
11. Install strike into door jamb.
10. Install the internal lever ensuring the
handle points towards the door hinges.
Warnings
Do not install batteries until the lock is
completely installed on the door.
Failure to follow these instructions could
result in damage to the product and void the
factory warranty.
The accuracy of the door preparation is critical
for the functioning and security of this product.
Misalignment can cause performance
degradation and lessening of security.
Finish Care: This lockset is designed to provide
the highest standard of product quality and
performance. Care should be taken to ensure a
long-lasting finish. When cleaning is required,
use a soft, damp cloth. Do not use lacquer
thinner, caustic soaps, abrasive cleaners or
polishes as these can damage the coating and
result in tarnishing.
Silent mode:
Disables the tone sound.
Status indicators:
Located on exterior assembly.
Definitions
Master mode:
The master mode could be entered by entering
[**Master PIN Code #] to program the lock.
Master PIN code:
The master PIN code is used for programming
and for feature settings.
Shutdown time:
The lock will shutdown for a default of 3 minutes
and not allow operation after the wrong code
entry limit (5 times) has been met. When the unit
is in shutdown, the light will flash if you are trying
to use the keypad.
User PIN code:
The user PIN code operates the lock. Maximum
number of user PIN codes is 20.
Fake PIN code:
Random numbers that are added before or
after the user PIN. This prevents the user PIN
from being exposed.
Reset button:
After reset operation, the lock will be restored to
factory default settings, all user credentials will
be deleted. Refer to page 11 for instructions on
how to reset your lock.
Passage mode:
The lock can be switched to passage mode by
toggling the switch on the internal side. In this
mode, it is unlocked inside/out and you may
enter freely. You may still lock the unit externally
by holding any key for 2 seconds. It will resume
passage mode when unlocked via PIN or key
override until the passage mode switch is shifted
to the locked position. Note: Enabling and
disabling passage mode can only be done on the
internal side of the unit via the switch.
Item Specifications Notes
External assembly 165mm (L) x 70mm (W) x 22mm (D)
196mm (L) x 73mm (W) x 28mm (D)
AA alkaline battery x 4
(Operation voltage: 4.6~6.0V)
Operation temperature:
-20ºC to 55ºC
Lasts up to one year
(10 times open/close per day)
Internal assembly
Battery
Hardware specifications
Enter
**Master PIN code #
Notes:
1. Beeps sound only when sound is enabled.
2. If the indicators show 3 red lights and 3 beeps, your setting has failed. The system will exit master mode.
Please enter master mode to try again.
3. Refer to page 9 for guidelines on setting PIN codes.
Enter
**Master PIN code #
Enter
**Master PIN code #
Enter
**Master PIN code #
Enter
**Master PIN code #
Enter
New user PIN code #
2. Alternatively, use the backup key provided.
Normal mode
1. Enter the master
or user PIN code,
followed by #,
then rotate the
lever to open the
door. Door will
automatically
re-lock 7 seconds
later. If you wish
to deactivate the
7-second auto re-lock feature,
switch to passage mode (page 10).
Setting PIN codes
1. Master PIN Code (4~10 digit): Default
master PIN code is “12345678”, please
modify it after installation.
If you forget your master PIN code, you
can reset your lock back to factory settings
(refer to page 11 for instructions).
2. User PIN Code (4~10 digit): User PIN codes
can be set up through master PIN code.
Up to 20 user PIN codes can be stored.
3. Both master and user PIN codes don’t
support the following combination of numbers.
If unit is locked and you require emergency
battery power, located on the bottom of
the external unit is a micro USB port (refer to the
exterior assembly diagram on page 3). Using a
micro USB cable and charged power bank, you
can power the lock to regain access as required.
Indice
Altri manuali Schlage Serratura della porta
Schlage
Schlage Dexter JD60 Manuale utente
Schlage
Schlage Schlage LiNK Manuale utente
Schlage
Schlage VIP 5100 series Manuale utente
Schlage
Schlage Custom FC21 Manuale utente
Schlage
Schlage S-5600 Manuale utente
Schlage
Schlage Artus Manuale utente
Schlage
Schlage BE469 Manuale utente
Schlage
Schlage LINK FE599 Manuale utente
Schlage
Schlage BR260 Manuale utente
Schlage
Schlage D170 Manuale utente
Schlage
Schlage Accents BA-362 Manuale utente
Schlage
Schlage KING COBRA KC5196-R Manuale
Schlage
Schlage ND10 Manuale utente
Schlage
Schlage S-510 Manuale utente
Schlage
Schlage LE162 Schema elettrico
Schlage
Schlage L9000 Series Manuale utente
Schlage
Schlage Lock with Built-in Alarm Manuale utente
Schlage
Schlage BE468 series Manuale utente
Schlage
Schlage DCT-A00XP14-00 Manuale utente
Schlage
Schlage CO-250 Manuale utente
