Schlage L9000 Series Manuale utente
*P516-909*
P516-909
1 IMPORTANT! Check lock handing before installation
To change handing:
1. Pull out the latch
and rotate 180°.
2. Remove the lock
handing screw
from one side of
the chassis and
install it on the
opposite side.
The lock handing
screw should
always be on the
interior side of
he door.
Pull
Rotate
180°
Handing
screw
2 Prepare the door for indicator trim
Two Z\," pilot holes are required to mount the indicator.
ONLY ONE SIDE OF THE DOOR – THE INDICATOR SIDE –
REQUIRES THIS PREPARATION. Use the template included in
the package to mark the location of the pilot holes before drilling.
Inside of door Outside of door
¹⁄₈" pilot
hole x 2
¹⁄₈" pilot
hole x 2
Indicator trim is available for either the inside or outside of the door on allowable functions.
Non-indicator trim is furnished on the opposite side of the door.
The L9000 lock with indicator is not intended for exterior door applications.
For retrot, see page 7.
Thumb
turn
Check the door preparation dimensions with the template included in the package.
Inside cylinder indicator with outside cylinder
non-indicator sectional trim shown
OR
OR
Tools
Non-indicator thumb turn or cylinder
furnished on inside of door when outside
of door is ordered with indicator trim,
depending on conguration.
Cylinder
L9000 Series Lock with Indicator Sectional Trim
L9000 Lock with Indicator
Installation Instructions
2
3 Install lock chassis
Note:
Pilot holes for
INDICATOR
ONLY
DO NOT FULLY TIGHTEN
CHASSIS MOUNTING SCREWS.
4 Install springs and spindles
All functions
Exterior
5
5a Install outside spring cage or spacer.
OR
LThe spring cage arrow
must point in direction
of lever down rotation.
Install spacer for L/LV9485
5b Install outside mounting posts.
LV functions
FULLY TIGHTEN MOUNTING POSTS ON SCREWS.
6 Install outside lever
All functions
Exterior
7 Install inside spring cage and mounting plate
LThe spring cage arrow
must point in direction
of lever down rotation.
Interior
3
8 Install inside lever and rose
All functions
9 Tighten bushing with spanner wrench
10 Install outside cylinder (if applicable)
Steps 10a – 10c for NON-INDICATOR TRIM ONLY
FOR INDICATOR OUTSIDE TRIM, SKIP TO STEP 11.
10a Insert key halfway into the cylinder.
10b Install the cylinder with cylinder spring as shown.
Functions
L/LV9050
L/LV9056
L/LV9060
L/LV9070
L/LV9071
L/LV9456
L/LV9457
L/LV9458
L9460
L9462
L9463
L9464
L9465
L9466
L9473
L/LV9485
LM/LMV9350
LM/LMV9370
LM/LMV9371
Key inserted halfway
10c Rotate cylinder clockwise.
4
11 Install outside INDICATOR with cylinder (if applicable)
Steps 8a – 8g for INDICATOR TRIM ONLY
11a Install the indicator mounting plate.
Functions
L/LV9050
L/LV9056
L/LV9060
L/LV9070
L/LV9071
L/LV9456
L/LV9457
L/LV9458
L9460
L9462
L9463
L9464
L9465
L9466
L9473
L/LV9485
LM/LMV9350
LM/LMV9370
LM/LMV9371
Mounting plate
11b Adjust the cam spindle length.
Cut the spindle at the appropriate mark
according to door thickness.
For 2Z\v” door do not cut the spindle.
11c Install the indicator slide and cam.
Indicator
slide
Cam
11d Connect the cam to the indicator slide. The cam must
engage either the left or right side of the indicator slide
according to door handing and indicator location.
• Unlock the door.
• Move the indicator slide against the top rim of the
mounting plate (unlocked position).
• Assemble the cam as shown.
Door Hand/Indicator Location
Lock Type
Non-deadbolt
functions
RH/Outside
LH/Inside
RH/Inside
LH/Outside
Deadbolt
functions
RH/Inside
LH/Outside
RH/Outside
LH/Inside
11e Insert key halfway into the cylinder.
11f Install the indicator faceplate and cylinder with cylinder
spring as shown.
Key inserted
halfway
Indicator
faceplate
11g Rotate cylinder clockwise.
5
12 Install inside thumb turn or cylinder
Steps 12a – 12b for NON-INDICATOR TRIM ONLY
FOR INDICATOR INSIDE TRIM, SKIP TO STEP 13.
Thumb turn:
(1) Rotate 180°
(2)
Functions
L/LV9040
L/LV9044
L/LV9050
L/LV9056
L/LV9456
L/LV9457
L/LV9458
L9460
L9473
L/LV9485
LM/LMV9350
(3)
– OR –
Cylinder:
Rotate clockwise
(2)(1)
Functions
L/LV9060
L/LV9071
L9462
L9463
L9466
LM/LMV9371
13 Install inside INDICATOR cylinder (if applicable)
Steps 13a – 13g for INDICATOR TRIM ONLY
13a Install the indicator mounting plate.
Mounting plate
Functions
L/LV9060
L/LV9071
L9462
L9463
L9466
LM/LMV9371
13b Adjust the cam spindle length.
Cut the spindle at the appropriate mark
according to door thickness
For 2Z\v” door do not cut the spindle.
13c Install indicator slide and cam.
Indicator
slide
Cam
6
13d Connect the cam to the indicator slide. The cam must
engage either the left or right side of the indicator slide
according to door handing and indicator location.
• Unlock the door.
• Move the indicator slide against the top rim of the
mounting plate (unlocked position).
• Assemble the cam as shown.
Door Hand/Indicator Location
Lock Type
Non-deadbolt
functions
RH/Outside
LH/Inside
RH/Inside
LH/Outside
Deadbolt
functions
RH/Inside
LH/Outside
RH/Outside
LH/Inside
13e Insert key halfway into the cylinder.
13f Install the indicator faceplate and cylinder with cylinder
spring as shown.
Indicator
faceplate
Key inserted
halfway
13g Rotate cylinder clockwise.
14
14a Tighten cylinder mounting screw.
14b Tighten top and bottom chassis mounting screws.
Cylinder
mounting
screw
ab
Chassis
mounting
screws
15 Install armor front
All functions
7
INDICATOR LOCK RETROFIT INSTRUCTIONS
1 Remove armor front 2 Remove cylinder(s), if applicable
2a Loosen the cylinder mounting screw.
2b Remove the inside cylinder, if applicable.
Insert the key halfway into the cylinder and rotate cylinder
counterclockwise to remove.
Key inserted halfway
2c Remove the outside cylinder.
Insert the key halfway into the cylinder and rotate cylinder
counterclockwise to remove.
Key inserted halfway
3 Check door preparation
IMPORTANT
• To install the indicator trim, additional door preparation
may be required. If additional door preparation is required,
remove the lock chassis from the door before drilling. Steps
for reassembly are included in this instruction sheet.
• Please refer to the template included in this package.
• Make sure the door is prepared with any necessary holes for
the indicator trim.
4 Complete installation of indicator trim
Go to STEP 11 ON PAGE 4 and follow the instructions to
complete the installation of the indicator trim.
Customer Service
1-877-671-7011 www.allegion.com/us
*P516-909*
P516-909
El borde con indicador está disponible para el interior o el exterior
de la puerta para las funciones permitidas. El borde sin indicador
se coloca en el lado opuesto de la puerta.
La cerradura L9000 con indicador no está destinada para
aplicaciones en puertas exteriores.
Para una adaptación, vea la página 17.
La garniture d’indicateur est vendue pour l’Intérieur ou l’extérieur de
la porte pour les fonctions autorisées. Une garniture sans indicateur
est fournie pour le côté opposé de la porte.
La serrure L9000 avec indicateur n’est pas conçue pour des
utilisations sur une porte extérieur.
Pour la rénovation, reportez-vous à la page 17.
Giro manual
Barrette
tournante
Compruebe las dimensiones de preparación de la puerta con la plantilla incluida en el paquete.
Vériezlesdimensionsdepréparationdelaporteàl’aidedugabaritinclusdansl’emballage.
Se muestra el indicador del cilindro interior y
el cilindro sin indicador en el exterior.
Indicateur de cylindre intérieur et cylindre
sans indicateur illustrés.
O
OU
Herramientas / Outils
El giro manual o cilindro sin indicador se incluye
en la parte interior de la puerta cuando el exterior
de la puerta se solicita con borde con indicador, de
acuerdo con la conguración.
La barrette tournante ou le cylindre sans indicateur
est fourni à l’intérieur de la porte lorsque vous
commandez l’extérieur de la porte avec la garniture
d’indicateur, en fonction de la conguration.
Cilindro
Cylindre
O
OU
Cerradura Serie L9000 con seccional de seguridad con indicador
Serrure de la série L9000 avec sectionnel d’indicateur d’entrée de serrure
Cerradura L9000 con indicador
Serrure L9000 avec indicateur
Instrucciones de instalación
Notice d’installation
10
1 ¡IMPORTANTE! Compruebe el lado de la cerradura
antes de la instalación.
IMPORTANT!Vériezsilaserrureestpourdroitierou
gaucher avant de l’installer.
Para cambiar el lado:
1. Extraiga la cerradura
y gire 180°.
2. Retire el tornillo del lado
de la puerta de un lado
del chasis y colóquelo
en el lado opuesto.
El tornillo del lado de
la cerradura siempre
debe estar en el lado
interior de la puerta.
Pour changer la main
d’ouverture :
1. Retirezleloquetet
tournez-lede180°.
2. Enlevezlavis
déterminant la main
d’ouverture de la serrure
d’uncôtédubâtietinstallez-la
du côté opposé. La vis déterminant la main d’ouverture
de la serrure devrait toujours se trouver du côté intérieur
de la porte.
Extraiga
Retirez
Gire
Tournez
180°
Tornillo del lado
Vis déterminant
la main
2 Preparar la puerta para el borde con indicador
Préparer la porte pour la garniture d’indicateur
Se requieren dos oricios piloto de Z\,” para montar el
indicador.
SOLO UN LADO DE LA PUERTA – el lado del indicador – requiere
esta preparación. Use la plantilla incluida en el paquete para marcar
laubicacióndelosoriciospilotoantesdeperforar.
Deux trous pilotes de 32 mm (Z\, po) sont requis pour
installer l’indicateur.
SEUL UN CÔTÉ DE LA PORTE – le côté indicateur – exige cette
préparation.Utilisezlegabaritinclusdansl’emballagepourmarquer
l’emplacement des trous pilotes avant de les percer.
Interior de la puerta
Intérieure de la porte
Orificios
piloto de ¹⁄₈"
Trous pilotes
(¹⁄₈" po)
x 2
Exterior de la puerta
Extérieure de la porte
Orificios
piloto de ¹⁄₈"
Trous pilotes
(¹⁄₈" po)
x 2
3 Instale el chasis de la cerradura
Installezlebâtidelaserrure
Nota:Oricios
piloto solo para
el indicador
Remarque :
Trous pilotes
pour indicateur
uniquement
NO AJUSTE POR COMPLETO LOS
TORNILLOS DE MONTAJE DEL CHASIS.
NE SERREZ PAS COMPLÈTEMENT
LES VIS DE MONTAGE DU BÂTI.
4 Instale los resortes y husillos
Installezlesressortsetlesaxes
Todas las funciones
Toutes fonctions
Exterior
Extérieur
Altri manuali per L9000 Series
8
Indice
Lingue:
Altri manuali Schlage Serratura
Schlage
Schlage CO-100 Manuale utente
Schlage
Schlage CO-100 Manuale utente
Schlage
Schlage HDB Manuale utente
Schlage
Schlage AL-SERIES Manuale utente
Schlage
Schlage FE575 Manuale utente
Schlage
Schlage CO-100-CY-70-KP-RHO-626 Manuale utente
Schlage
Schlage F-Series Manuale utente
Schlage
Schlage D-Series Manuale utente
Schlage
Schlage SED100 Manuale utente
Schlage
Schlage D50 Manuale utente
Schlage
Schlage LT Series Manuale di servizio
Schlage
Schlage ND170 Manuale utente
Schlage
Schlage Door Lock Manuale utente
Schlage
Schlage NDE80 Istruzioni per il montaggio
Schlage
Schlage S-7100 Manuale utente
Schlage
Schlage FE595 Manuale utente
Schlage
Schlage BE365 Manuale utente
Schlage
Schlage 672 Series Manuale utente
Schlage
Schlage D-Series Manuale utente
Schlage
Schlage KING COBRA Istruzioni operative
