Schlage WRI-OTD-12VDC Manuale utente

Wireless Access

INSTALLATION INSTRUCTIONS

WIRELESS READER

INTERFACE - OUTDOOR

(WRI-OTD-12VDC or AUWRI-OTD-12VDC)

The most current version of this document is available for download at:

http://www.ir-swa.com

P/N: M053-003-C

Wireless Access

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Bldg 7, Suite 48, West Chicago, IL 60185 / (800) 313-2962 / (630) 293-4257 fax

P/N: M053-003-C www.ir-swa.com Page 2 of 20

Schlage

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Building 7, Suite 48

West Chicago, IL 60185

main: 800-313-2962 (630-876-5680)

technical support: 866-322-1237

fax: 630-293-4257

web: ir-swa.com

No part of this document can be reproduced, transmitted, or transcribed in any form by electrical, mechanical, optical, manual, or

otherwise without the prior written consent of Ingersoll Rand. Ingersoll Rand reserves the right to alter or revise the content of

this document as needed to support future product revisions, without obligation to notify any persons of specific changes.

The use of trademarks, trade names, or other product identification is solely for reference purposes. All other product brand

names are trademarks or registered trademarks of their respective holders.

Ingersoll Rand believes the information in this document to be accurate and reliable. Ingersoll Rand does not guarantee results

from the use of this information. Ingersoll Rand assumes no responsibility, obligation, or liability for the information presented in

this document.

Wireless Access

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Bldg 7, Suite 48, West Chicago, IL 60185 / (800) 313-2962 / (630) 293-4257 fax

P/N: M053-003-C www.ir-swa.com Page 3 of 20

INSTALLATION INSTRUCTIONS

Wireless Reader Interface - Outdoor (WRI-OTD)

NOTE: These instructions are for installing the Wireless Reader Interface-Outdoor (WRI-OTD-12VDC), a

component of a Wireless Access System. AUWRI-OTD-12VDC is an Australian version of the outdoor wireless

reader interface.

In this manual, WRI-OTD refers to either a WRI-OTD-12VDC or an AUWRI-OTD-12VDC model.

After completing this installation refer to the “Configuring and Operating the Schlage Wireless Access System”

manual.

Table of Contents

1. Schlage Wireless Access System Components...............................................................................................4

1.1 Overview .......................................................................................................................................................4

2. Wireless Reader Interface-Outdoor (WRI-OTD) Components & Sales Models .......................................4

3. Installing the WRI-OTD .................................................................................................................................5

3.1 Tools – Hardware Required...........................................................................................................................5

3.2 Remote Antenna ............................................................................................................................................6

3.3 Determining the Best WPIM and WRI-OTD Locations................................................................................6

3.4 Mounting the WRI-OTD ...............................................................................................................................9

3.5 Getting Wires In & Out of the WRI-OTD...................................................................................................10

3.6 Wiring the WRI-OTD to its Access Control Peripherals.............................................................................10

4. WRI-OTD Cable/Wire Specifications..........................................................................................................17

5. Contacting Technical Support......................................................................................................................18

6. FCC/UL Compliance & Warnings...............................................................................................................19

6.1 FCC Compliance .........................................................................................................................................19

6.2 ACA Compliance.........................................................................................................................................19

6.3 UL Compliance............................................................................................................................................19

6.4 Warnings......................................................................................................................................................19

7. Revision History.............................................................................................................................................20

Wireless Access

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Bldg 7, Suite 48, West Chicago, IL 60185 / (800) 313-2962 / (630) 293-4257 fax

P/N: M053-003-C www.ir-swa.com Page 4 of 20

1. Schlage Wireless Access System Components

1.1 Overview

Every access control system that uses Schlage Wireless Access contains two different types of modules

(Figure 1-1):

•at least one Wireless Panel Interface Module (WPIM), and

•at least one Wireless Access Point Module (WAPM)

Figure 1-1 – Wireless Access System Block Diagram

The Schlage Wireless Access product line contains several different expressions of each module.

The WPIM is wired to the access control panel and ideally is installed very close to the access control

panel. The WPIMs installation location is determined by the location of the WAPMs with which it will

communicate using RF.

The WAPM is installed at the access point where access will be controlled and/or monitored. Depending

on the application and which WAPM is used, some wiring at the access control point may be required.

Regardless of which WPIM or WAPM module is used, the communication link between the WPIM and

WAPM is always RF.

This manual describes the installation of a Wireless Reader Interface - Outdoor (WRI-OTD-12VDC or

AUWRI-OTD-12VDC) which is a WAPM.

1.2 Wireless Reader Interface-Outdoor (WRI-OTD) Components & Sales

Models

The WRI-OTD (Figure 1-4) includes the following components:

•2 reader/keypad connectors (#1)

•strike relay connector (#2)

•auxiliary relay connector (#3)

•door position input (#4)

•request to exit input (#4)

•request to enter input (#4)

•tamper input & tamper switch (#5)

•RS485 port (#6)

Wireless Access

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Bldg 7, Suite 48, West Chicago, IL 60185 / (800) 313-2962 / (630) 293-4257 fax

P/N: M053-003-C www.ir-swa.com Page 5 of 20

•2 indicator LEDs (#7)

•flash programming port (#8)

•RF Transceiver (#9)

Figure 1-2 – Front of the WRI-OTD

Figure 1-3 – Inside the WRI-OTD

Figure 1-4 - WRI-OTD Printed Circuit Board

MODEL MOUNTING LOCATION

WRI-OTD-12VDC Surface indoor/outdoor

AUWRI-OTD-12VDC Surface indoor/outdoor

Table 1-1- WRI-OTD Sales Model Table

2. Installing the WRI-OTD

2.1 Tools – Hardware Required

•Drill & drill bits (the size will depend on the mounting fasteners used)

•Flat and Phillips head screwdrivers (1/8” wide flat blade for screw terminals)

Wireless Access

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Bldg 7, Suite 48, West Chicago, IL 60185 / (800) 313-2962 / (630) 293-4257 fax

P/N: M053-003-C www.ir-swa.com Page 6 of 20

•Pencil (#2 lead)

•Mounting hardware (not provided), four ¼” diameter screws or bolts and/or anchors, type and length

of fasteners depend on the mounting surface.

2.2 Remote Antenna

If the WRI-OTD installation uses the Remote Antenna Module (RAM) option, please refer to the

“Remote Antenna Module Installation” manual before proceeding.

2.3 Determining the Best WPIM and WRI-OTD Locations

Proper selection of WPIM and WRI-OTD module mounting locations insures reliable RF

communications.

The WPIM manual contains a section for determining the best location for the WPIM.

The maximum distance between WPIM and a WRI-OTD is 200’ horizontally when installed inside a

building on the same floor that uses normal building construction materials. Never locate the WRI-OTD

or RAM & WPIM & RAM more than one (1) floor apart. If on different floors, limit the maximum

horizontal distance to 100’. Do not locate on different floors if the building’s floors use concrete over

metal construction. The maximum distance is up to 1000’ for a line of sight installation using the internal

antenna. If an external directional 6 db gain antenna (ANT-REM-I/O+6DB) is used on either the WRI-

OTD or WPIM and properly aimed, then the maximum line of sight distance can be increased to 2000’. If

external directional 6 db gain antennae (ANT-REM-I/O+6DB) are used on both the WRI-OTD and

WPIM and properly aimed, then the maximum line of sight distance can be increased up to 4000’.

This section provides additional application specific help and guidelines to select the best mounting

location for the WPIM and WRI-OTD modules.

NOTE: A WRI-OTD located with a substantial steel barrier intervening between it and the PIM

may require alternate WRI-OTD and/or PIM placement in order to ensure reliable RF

communications. In these applications, mount the PIM remote from the access control panel.

Choose the PIM location to prevent “shadowing” of the WRI-OTD from PIM radio transmissions.

RAMs may be used to get over, under, through, or around obstacles with a limit of 15-20 cable feet

distance between it’s WRI-OTD or WPIM and it’s RAM.

2.3.1 Outdoor Gate Applications

This section describes the ideal mounting locations for the WRI-OTD and WPIM to control an

outdoor gate (Figure 2-1).

The WRI-OTD has not been evaluated to UL325.

Wireless Access

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Bldg 7, Suite 48, West Chicago, IL 60185 / (800) 313-2962 / (630) 293-4257 fax

P/N: M053-003-C www.ir-swa.com Page 7 of 20

Figure 2-1 – Outdoor Gate Installation

WPIM location guidelines for outdoor gate applications:

•Mount the WPIM indoors, within the secured portion of the premises.

•Install the WPIM just inside the building’s outer wall that faces the gate.

•If the WRI-OTD(s) to be controlled by this WPIM are outdoors, use the remote WPIM

antenna option. Mount the Remote Antenna Module outside of the building, in direct line-of-

sight to the WRI-OTD(s) that it controls.

•Never install the WPIM in an all metal room or a room with wire screening/mesh in the walls,

without the remote WPIM antenna option located outside that room.

•If a site uses more than one WRI-OTD, install the WPIM within direct sight of both WRI-

OTDs under its control, and never more than 1000 feet away from either using the internal

WRI-OTD and WPIM antennae. Refer to section 2.3, above, to increase this range using

external remote antennae. Use a separate WPIM for each WRI-OTD if the site geometry

makes this necessary.

•When using the standard WPIM antenna, mount the WPIM 6 feet or more from the floor.

WRI-OTD Location Guidelines for outdoor gate applications:

•Mount the WRI-OTD within the secured portion of the premises, in direct line-of-sight to the

WPIM’s antenna.

•Orient the WRI-OTD upright, preferably on the side of the gate closest (facing) the WPIM.

•Avoid obstructions between the WRI-OTD antenna and WPIM antenna.

2.3.2 Elevator Applications

Note: These elevator applications deal only with access control portion and not elevator control. The

WRI-OTD has not been evaluated to UL508.

Wireless Access

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Bldg 7, Suite 48, West Chicago, IL 60185 / (800) 313-2962 / (630) 293-4257 fax

P/N: M053-003-C www.ir-swa.com Page 8 of 20

This section describes the ideal locations to mount the WRI-OTD and WPIM to control a typical

cabled hoist elevator (Figure 2-2) or a typical hydraulic elevator (Figure 2-3).

Figure 2-2 – Cabled Hoist Elevator Installation

Figure 2-3 – Hydraulic Elevator Installation

2.3.2.1 Cabled hoist machine installations with upper machine rooms (Figure 2-2)

Mount the WPIM inside the secured portion of the premises. For example, mount the WPIM

within the secured elevator machine room, and mount remote WPIM antenna inside the shaft, on

the ceiling of the shaft. Keep in mind that the remote antenna has a cable length of 15 feet, so

locate the WPIM enclosure so that the antenna cable reaches. Mount the assembly such that the

WPIM antenna has a direct line of sight to the WRI-OTD throughout the entire shaft. No

structural members should obstruct its view to the WRI-OTD.

Mount the WRI-OTD on top of the cab, lying down if possible (Figure 2-2).

2.3.2.2 Cabled hoist machine installations with lower machine rooms (Figure 2-3)

If the machine room resides at the bottom of the shaft, install the components per section 2.3.2.3,

like hydraulic machines. Use the Remote Antenna Module with the WPIM to prevent

contamination of the WPIM from settled dust, oil, and debris.

2.3.2.3 Hydraulic Machine Installations (Figure 2-3)

Locate the WPIM enclosure in a secured area of the premises, outside of the shaft pit, where it

will be free of contamination from oil. Use the Remote Antenna Module with the WPIM. Mount

the Remote Antenna Module horizontally in the shaft pit, at a height where oil leakage and

debris cannot submerge it. For reliability of communications, the Remote Antenna Module must

have a direct line of sight to the WRI-OTD throughout the entire shaft. No structural members,

including the ram, should obstruct its view of the WRI-OTD.

Mount the WRI-OTD on the underside of the cab.

Wireless Access

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Bldg 7, Suite 48, West Chicago, IL 60185 / (800) 313-2962 / (630) 293-4257 fax

P/N: M053-003-C www.ir-swa.com Page 9 of 20

2.3.3 Indoor WRI-OTD Reader & Electrified Lock/Access Point Applications

These applications include door installations with magnetic locks, electric strikes, electrified exit

devices (using EL kits), or automatic door openers; Wiegand or clock & data type readers; and other

peripheral hardware. Since these types of installations do not generally have line-of-sight between

WPIM and WRI-OTD, the specified communication range has a 200 foot limit for normal indoor

construction when located on the same floor. Follow the guidelines in the WPIM installation manual.

2.4 Mounting the WRI-OTD

Four mounting feet and four screws (10-32 X 3/8”) are provided with the WRI-OTD to permanently

attach the WRI-OTD enclosure in its desired location.

2.4.1 From the rear of the WRI-OTD enclosure, attach the four mounting feet with the four screws as

shown in Figure 2-4). The mounting feet must be installed so that the four screw heads are recessed

and the hex protrusion on the mounting feet align with the hex recession on the enclosure.

Figure 2-4 – Rear View of WRI-OTD Enclosure

2.4.2 Drilling the Weep Hole - Before the WRI-OTD is permanently mounted, determine the lowest point

of the WRI-OTD enclosure and drill a 1/16” hole from the exterior to the interior. This hole provides

an exit for any moisture buildup that might occur due to the weather tightness of the enclosure.

NOTE: When drilling, make certain that the drill bit does not damage any electronics inside the

enclosure. Use light drill pressure so that the bit does not enter the enclosure very far when the bit

breaks through the inside of the enclosure.

2.4.3 Place the WRI-OTD in the desired mounting location, on the mounting surface, mark the location of

the four mounting holes (one in each mounting foot).

2.4.4 Choose the appropriate type of fasteners (not supplied) for the mounting surface material (i.e. screws

for wood, bolts and nuts for metal, screws with anchors for masonry, drywall, or plaster).

2.4.5 At the marks made in section 2.4.3, drill holes in the mounting surface. The hole size will depend on

the fastener being used.

2.4.6 Fasten the WRI-OTD enclosure to the mounting surface using the selected fasteners and mounting

feet holes.

Wireless Access

Ingersoll Rand Security Technologies

245 W. Roosevelt Road, Bldg 7, Suite 48, West Chicago, IL 60185 / (800) 313-2962 / (630) 293-4257 fax

P/N: M053-003-C www.ir-swa.com Page 10 of 20

2.5 Getting Wires In & Out of the WRI-OTD

2.5.1 Weather Tight Installation

A NEMA 4X certified Wiring Gland (Figure 2-5) should be used to achieve a weather tight

installation when wires enter or exit the WRI-OTD. Wiring Glands are available from Bud Industries,

Inc. (http://www.budind.com/cgi-bin/view?part=n4-cg). The Bud Industries Wiring Gland consists of

a black molded nylon body, hex nut, and cable nut and with a rubber gasket and cable seal. The

Wiring Glands are available in various sizes. The appropriate size will depend on the number and

type of cables used in each installation.

Drill hole(s) in the WRI-OTD enclosure to accommodate the size and number of Wiring Glands to be

used. All wiring holes must be located near the bottom of the enclosure. Suggested locations are

indicated by dimples on the outside of the enclosure.

NOTE: When drilling, make certain that the drill bit does not damage any electronics inside the

enclosure. Use light drill pressure so that the bit does not enter the enclosure very far when the bit

breaks through the inside of the enclosure.

Figure 2-5 – Typical Wiring Gland

2.5.2 Non Weather Tight Installation

If the WRI-OTD is mounted in a location where weather tightness is not a requirement, then use

wiring entry/exit connectors that are compliant with local electrical codes (i.e. conduit, etc.)

Drill hole(s) in the WRI-OTD enclosure to accommodate the size and number of entry/exit connectors

to be used. All wiring holes must be located near the bottom of the enclosure. Suggested locations

are indicated by dimples on the outside of the enclosure.

NOTE: When drilling, make certain that the drill bit does not damage any electronics inside the

enclosure. Use light drill pressure so that the bit does not enter the enclosure very far when the bit

breaks through the inside of the enclosure.

2.6 Wiring the WRI-OTD to its Access Control Peripherals

There are seven WRI-OTD PCB connectors that provide connections to Access Control Peripherals that

the WRI-OTD will monitor and/or control (Figure 2-6):

•DC Input Power (J3)

•RS485 (J9)

•Tamper Input (J2)

•Portal Inputs (J7)

•Portal Outputs (J8)

•Card Reader 1 (J4)

•Card Reader 2 (J5)

Some of the connections are optional based on the specific application of the WRI-OTD. Refer to

Section 3 for cable and wire specifications for the WRI-OTD.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Schlage Punto di accesso wireless

Schlage

Schlage WRI-IN-12VDC Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente