Schwinn SC5 Manuale utente
ASSEMBLY
MANUAL
Schwinn® SC5/SC7/SC Power
Core Health & Fitness
Page 1
SC5 / SC7 / SC Power Assembly Manual
Applies to: SC5 (9-7410) + SC7 (9-7400) + SC Power (9-7380)
SC5 ASSEMBLY INSTRUCTIONS
1. Install the front stabilizer using two (2) pieces
each of the M10 x 25mm hex head screws, M10
split lock washers, and M10 washers. Repeat this
step to attach the rear stabilizer.
2. Install the seat post by loosening the height ad-
justment pop pin, then pulling outwards on the
pin while sliding the seat post into the frame.
3. Pull down on the seat slider locking pin then
slide the seat assembly onto the seat post in-
stalled in Step 2, tightening the fore/aft adjust-
ment knob to lock the seat slider into place.
NOTE: The fore/aft adjustment knob may need to be
loosened.
Page 2
4. Insert one (1) piece of the trapezoidal fore/aft
locking block into the handlebar post then slide
the handlebars onto the handlebar post. Once
the block is inside the handlebar post, use a 3mm
allen key to secure the end cap to the post using
one (1) M4 x 10mm screw.
5. Secure one (1) piece of the threaded collar knob
insert through the handlebars and into the trap-
ezoidal fore/aft locking nut using a 10mm allen
key. Next, slide one (1) piece of the M8 washer
onto the fore/aft adjustment knob then tighten
the fore/aft adjustment knob into the threaded
collar locking knob insert.
6. Install the user right side pedal into the crank
arm then use a torque wrench and a 8mm allen
socket to secure one (1) piece of the crank bolt
from the other side of the pedal, torquing to
33-37 ft-lbs (45-50 Nm). Repeat this step for the
rider left side pedal.
CAUTION: The pedal MUST be torqued to the above
specications otherwise a failure of the pedal may
occur.
Trapezoidal
Locking
Block
Fore/Aft
Adjustment
Knob
M8 Washer
Threaded Collar
Locking Knob
Insert
Page 3
SC7 ASSEMBLY INSTRUCTIONS
1. Slide the threaded stabilizer plate into the bike
frame then use a 13mm socket to secure the rear
stabilizer onto the frame using two (2) pieces
each of the M8 x 32mm bolts, M8 split lock wash-
ers, and M8 at washers. Repeat this step for the
front stabilizer.
2. Insert one (1) piece of the trapezoidal fore/aft
locking block into the handlebar post then slide
the handlebars onto the handlebar post. Once
the block is inside the handlebar post, use a 3mm
allen key to secure the end cap to the post using
one (1) M4 x 10mm screw.
3. Secure one (1) piece of the threaded collar knob
insert through the handlebars and into the trap-
ezoidal fore/aft locking nut using a 10mm allen
key. Next, slide one (1) piece of the M8 washer
onto the fore/aft adjustment knob then tighten
the fore/aft adjustment knob into the threaded
collar locking knob insert
4. Use a 21mm open-ended wrench to install the
seat post pop pin into the frame, turning clock-
wise to tighten.
Threaded
Stabilizer
Plate
Fore/Aft
Adjustment
Knob
M8 Washer
Threaded Collar
Locking Knob
Insert
Trapezoidal
Locking
Block
Page 4
5. Slide the seat post into the frame by loosening
the seat post pop pin, then pulling outwards on
the pin while sliding the seat into the frame.
6. Pull down on the seat slider locking pin then
slide the seat assembly onto the seat post in-
stalled in Step 3, tightening the fore/aft adjust-
ment knob to lock the seat slider into place.
7. Install the pedal into the crank arm then use a
torque wrench and a 8mm allen socket to secure
one (1) piece of the crank bolt from the other
side of the pedal, torquing to 33-37 ft-lbs (45-50
Nm). Repeat this step for the rider left side pedal.
CAUTION: The pedal MUST be torqued to the above
specications otherwise a failure of the pedal may
occur.
Page 5
SC POWER ASSEMBLY INSTRUCTIONS
1. Slide the threaded stabilizer plate into the bike
frame then use a 13mm socket to secure the rear
stabilizer onto the frame using two (2) pieces
each of the M8 x 32mm bolts, M8 split lock wash-
ers, and M8 at washers. Repeat this step for the
front stabilizer.
2. Insert one (1) piece of the trapezoidal fore/aft
locking block into the handlebar post then slide
the handlebars onto the handlebar post. Once
the block is inside the handlebar post, use a 3mm
allen key to secure the end cap to the post using
one (1) M4 x 10mm screw.
3. Secure one (1) piece of the threaded collar knob
insert through the handlebars and into the trap-
ezoidal fore/aft locking nut using a 10mm allen
key. Next, slide one (1) piece of the M8 washer
onto the fore/aft adjustment knob then tighten
the fore/aft adjustment knob into the threaded
collar locking knob insert
4. Use a 21mm open-ended wrench to install the
seat post pop pin into the frame, turning clock-
wise to tighten.
Threaded
Stabilizer
Plate
Trapezoidal
Locking
Block
Fore/Aft
Adjustment
Knob
M8 Washer
Threaded Collar
Locking Knob
Insert
Page 6
5. Slide the seat post into the frame by loosening
the height adjustment pop pin, then pulling
outwards on the pin while sliding the seat into
the frame.
6. Pull down on the seat slider locking pin then
slide the seat assembly onto the seat post in-
stalled in Step 3, tightening the fore/aft adjust-
ment knob to lock the seat slider into place.
7. Install the pedal into the crank arm then use a
torque wrench and a 8mm allen socket to secure
one (1) piece of the crank bolt from the other
side of the pedal, torquing to 33-37 ft-lbs (45-50
Nm). Repeat this step for the rider left side pedal.
CAUTION: The pedal MUST be torqued to the above
specications otherwise a failure of the pedal may
occur.
8. Refer to document 620-8594 “Echelon2G Assem-
bly Manual” contained within the Echelon2G box
to continue the installation of the SC Power.
620-8594
© 2018 CORE HEALTH & FITNESS, LLC PART NUMBER 620-8607, REV B
Altri manuali per SC5
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Schwinn Cyclette
Schwinn
Schwinn NAUTILUS A10 Manuale utente
Schwinn
Schwinn Schwinn A.C. Classic Manuale utente
Schwinn
Schwinn Airdyne Manuale utente
Schwinn
Schwinn Evolution Assembly Manuale utente
Schwinn
Schwinn 140 Manuale utente
Schwinn
Schwinn 10 Series Bike Manuale utente
Schwinn
Schwinn AD4 Airdyne Manuale utente
Schwinn
Schwinn 126 Upright Bike Manuale utente
Schwinn
Schwinn 170 Journey 1.5 Manuale utente
Schwinn
Schwinn IC ELITE Manuale utente
Schwinn
Schwinn a15 Manuale utente
Schwinn
Schwinn NAUTILUS A10 Manuale utente
Schwinn
Schwinn IC ELITE Manuale utente
Schwinn
Schwinn 190 Manuale utente
Schwinn
Schwinn Fitness 123 Manuale utente
Schwinn
Schwinn IC4/800IC Manuale utente
Schwinn
Schwinn SC7 Manuale utente
Schwinn
Schwinn Airdyne Manuale utente
Schwinn
Schwinn SC5 Manuale utente
Schwinn
Schwinn Airdyne Backdraft Manuale utente
