SCORPION SIGS39 Manuale utente

Rev.01 07/22

Installation Guide

Rev.01 07/22

SIGS39

Contents

1.0 - ALARM POSITIONING

2.0 - ACCESSORIES POSITIONING

2.1 - Override key receptacle

2.2 - Contact switch (Thatcham Requirement)

2.3 - Infra-Red Sensor

3.0 - ALARM UNIT SEALING

4.0 – ALARM POSITIONG FOR MAXIMUM SENSITIVITY

5.0 - ELECTRICAL CONNECTIONS

6.0 - WIRING DIAGRAM AND PINOUT

7.0 - PAIRING NEW DEVICES

7.1- With GREEN/BROWN wire ground connection

7.2 - Without GREEN/BROWN wire ground connection

8.0 - PROGRAMMABLE FEATURES

9.0 - PROGRAMMING EXAMPLE

10.0 - REMOTE CONTROL

11.0 - WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

12.0 - TECHNICAL SPECIFICATIONS

PAGE 3

PAGE 4

PAGE 5

PAGE 6

PAGE 8

PAGE 9

PAGE 10

PAGE 11

PAGE 12

PAGE 13

PAGE 14

PAGE 15

Rev.01 07/22

1.0 – Alarm Positioning

For maximum security the alarm should be mounted inside the caravan.

To ensure maximum sound volume in the event of an alarm trigger it is recommended that the

alarm is mounted close to an external air vent, if this is not possible it may be necessary to install an

air vent.

Note: Should the alarm be mounted in an area rain may enter, please ensure that the alarm is

mounted as in the image below.

Warning

If a jet wash is used to clean the vehicle, protect the alarm unit from water splashes and be careful

not to expose it to high pressure jets.

The warranty will not cover damages to the system due to water infiltrations caused by improper

installation, improper jet washing or the use of non-original accessories, not approved by the

manufacturer.

Do not install the alarm unit in this position as water

ingress over time may seep through the rubber sheath

and permanently damage the electronic circuit making

the alarm system unreliable. Eventual malfunctioning

due to water infiltration is not covered by warranty.

•

Install the alarm as shown in the picture opposite to

prevent water from entering.

•

Give the rubber sheath a `goose neck’ bending as shown

and secure with a cable tie.

•

Install the alarm away from moving mechanical parts,

electric or electronic components that could generate

high frequency electromagnetic disturbances and away

from devices that could reach high temperatures when in

use.

Rev.01 07/22

2.0 - Accessories Positioning

2.1 – Override key receptacle

The receptacle may be mounted inside or outside the caravan is should be mounted where it can

readily be seen and accessed by the user. Before drilling a 13mm hole for the receptacle, check the

receptacle will not be covered and that the user can easily operate the touch key.

2.2 – Contact Switch

For maximum security it is recommenced that contact switches are fitted onto the main habitation

door plus any locker doors, be careful the switches do not foul the operation of the doors or fly

screens. The switches may be of the wired or wireless type.

NB: If a wired switch is not fitted, the GREEN/BROWN wire should be insulated but remain free for

other possible uses such as programming the alarm or learning new devices.

2.3 – Infra-Red Sensor

Additional interior security may be obtained by installing a PIR sensor, Scorpion offer a wireless PIR

sensor (SIG909) should be mounted onto the ceiling of the caravan and has a detection range of

approximately 8M (diameter) when mounted at a ceiling height between 2 - 2.5M.

To avoid false alarms do not install the sensor in direct sunlight or directly above heat/air vents and

where pets have access and can trigger it.

Rev.01 07/22

3.0 - Alarm Unit Sealing

The alarm unit will be supplied with the rubber seal and plastic rectangular flange already fixed in

place, the following is for informational purposes should the unit need to be disassembled and

reassembled.

To seal the alarm, position the

rubber cap over the external edge of

the alarm housing.

Pull the plastic rectangular flange

over the rubber cap and secure with

the supplied screws.

Do not over tighten.

Rev.01 07/22

4.0 - Alarm Positioning for Maximum Sensitivity

To ensure the correct operation of the built-in motion sensor install the alarm flat as illustrated

below, this will allow coverage on all directions. The siren may be mounted with the siren cone

facing upward or downward.

Figure 3: motion sensor operation with alarm fitted horizontally, siren facing up or down.

The sensor will detect any movement of the motorcycle in any direction.

The alarm location in the image above is for illustration only, the alarm can be mounted at the

front, side or centre of the caravan.

Rev.01 07/22

Figure 4: motion sensor operation with siren facing sideways.

The alarm will only detect in the direction as indicated by the arrow in the drawing above. In order

for alarm to correctly detect a change of inclination the siren cone should either point towards the

front of the vehicle or towards the rear of the vehicle.

Figure 5: motion sensor operation with alarm fitted vertically.

If fitted in an arear that the alarm may be subjected to water, the wire rubber sheath must be

turned downwards to prevent water from entering the unit.

NOTE: Prior to fitting, test the operation of the sensor to confirm it will work in the intended

position.

To front of

Caravan

To rear of

Caravan

To rear of

Caravan

To front of

Caravan

Rev.01 07/22

5.0 - ELECTRICAL CONNECTIONS

WIRE COLOUR

CONNECTION

Black marked “M”

Connect to negative

Black marked “R”

Connect to positive

Orange

Not Used

Orange

Not Used

Black marked “G”

+15 Ignition

Green/Brown

Connect to contact switch or insulate

Pink

Positive output on alarm trigger

White/Violet

Device pairing

Black with Red sleeve

Antenna

WIRE COLOUR

CONNECTION

Black marked “B”

Not Used

Black marked “H”

Not Used

Black marked “HB”

Not Used

Black marked “H1”

Not Used

Black marked “B1”

Not Used

Rev.01 07/22

6.0 - WIRING DIAGRAM AND PINOUT

Rev.01 07/22

7.0 - PAIRING NEW DEVICES

7.1 - With GREEN/BROWN wire ground connection

The alarm is supplied with 2 remote controls and 1 override key but other optional devices can be

added.

To pair a new device, proceed as follows:

• Arm and then disarm the alarm via remote control or override key.

• Within 20 seconds of disarming the alarm ground the GREEN/BROWN wire.

• Connect the WHITE-VIOLET wire to ground.

• Press the ignition simulation switch to ON.

• A Beep and a Bop will confirm the system is in learn mode.

• Remove the WHITE-VIOLET wire from ground.

• Depending on which device is to be paired either press one of the remote-control buttons

OR touch the override key to its receptacle OR make the magnetic contact transmit (bring

contact and magnet together and then move apart) OR press the button on the opening

detector, make the infrared sensor or wireless hyper-frequency sensor transmit (refer to

sensor instructions).

• A Beep will confirm the operation has been completed successfully.

• To pair another device, ground the WHITE-VIOLET wire for 1 sec.

• To exit learn mode, press the ignition simulation switch to OFF.

• A Bop will confirm the end of the procedure. Remove the GREEN/BROWN wire from ground.

Altri manuali per SIGS39

Indice

Altri manuali SCORPION Accessori per motociclette

SCORPION

SCORPION Exo-GT3000 Manuale utente

SCORPION

SCORPION EXO-AT950 Manuale utente

SCORPION

SCORPION Commander ESC's Series Manuale utente

SCORPION

SCORPION SR-i900 Series Manuale utente

SCORPION

SCORPION RTR-75 Manuale utente

SCORPION

SCORPION RKA-88 Manuale utente

SCORPION

SCORPION EHA-95 Manuale utente

SCORPION

SCORPION Exo-R410 Manuale utente

SCORPION

SCORPION RBM-69 Manuale utente

SCORPION

SCORPION Commander Series Manuale utente

SCORPION

SCORPION Exo-CT220 Manuale utente

SCORPION

SCORPION RHA-188 Manuale utente

SCORPION

SCORPION TR-1001 Manuale utente

SCORPION

SCORPION SIGS39 Manuale utente

SCORPION

SCORPION RTR-87 Manuale utente

SCORPION

SCORPION RKT-72 Manuale utente

SCORPION

SCORPION EXO-700 Manuale utente

SCORPION

SCORPION RKT-89 Manuale utente

Manuali Accessori per motociclette popolari di altre marche

SRC

SRC B-TRK502-01-01-SL Manuale utente

3M Speedglas 9100 MP Manuale utente

hepco & becker

hepco & becker 6307520 00 01 Manuale utente

HOMCOM

HOMCOM AA0-077 Manuale utente

hepco & becker

hepco & becker 6307558 00 01 Manuale utente

Wunderkind Custom

Wunderkind Custom 106503-F15 Guida utente

Dräger

Dräger HPS 3500 Manuale utente

M-WAVE

M-WAVE SKI Manuale utente

Kuryakyn

Kuryakyn 6212 Manuale utente

hepco & becker

hepco & becker 6507504 00 01 Manuale utente

Tool it

Tool it PROMAX LCD 9.13G Manuale utente

Custom Dynamics

Custom Dynamics TruWrapz Manuale utente

Roof

Roof RO200 CARBON Manuale utente

Kabuto

Kabuto Japan IBUKI Manuale utente

PUIG

PUIG 5051 Manuale utente

rizoma

rizoma ZTH050 Manuale utente

Joubert

Joubert 10001711 Manuale utente

Sperian

Sperian Optrel p420 Manuale utente