SDC EntryCheck 918 Manuale utente

The 918 EntryCheck™ is a digital keyless entry system

designed for access control applications. The keypad is mounted

on a rugged, stainless steel faceplate and is designed to be

mounted in a standard single-gang electrical box. The indoor

backlit keys have bright, easy-to-read graphics.

Up to 500 entry codes, from 1 to 6 digits in length, can be

programmed. They can activate one or both of the relay

outputs. The programmable “anti-passback” feature prevents

using the same code again before the programmed time

elapses.

All system indicators are long-lasting, solid state LEDs. Two

indicators show the status of the entry system. The left indicator

lights red to indicate power, then turns green when access is

granted. The right indicator lights yellow when the keypad is in

“lockout” condition (from too many incorrect code entries). The

yellow LED flashes when the keypad is in programming mode.

An internal sounder beeps when each key is pressed. An

internal jumper sets the sounder volume high or low

The SENSE input can be used two ways. If programmed for

“door sense” the input is wired to a normally closed door contact

switch to detect when the door is opened or closed. Forced

entry or door ajar situations can then be detected. When using a

door contact switch, the “Auto-relock” feature will prevent

“tailgating” by turning off the Main Relay output immediately

when the door is closed after access has been granted. If the

SENSE input is programmed for “inhibit”, the input can be wired

to a “service” switch or automatic timer that will disable the Main

Relay when required.

The REQUEST-TO-EXIT input may be wired to a pushbutton to

provide codeless activation of Main Relay, Auxiliary Relay,

Output #3 or Output #4 (programmable).

The ALARM SHUNT output activates when access is granted.

This output can be wired to shunt alarm contacts on the access

door/gate to prevent triggering of an alarm when authorized

access occurs.

The 918 EntryCheck™ is powered from a 12/24VDC or AC

source. The EEPROM memory retains all entry codes and

programming, even without power. An internal jumper is

provided to reset the master code. The Main Relay has a 5 Amp

capacity. The Auxiliary Relay has a 2 Amp capacity. Two solid

state outputs, capable of switching 100 mA to common, are

programmable to signal forced entry, door ajar, lockout, alarm

circuit shunting, request-to-exit, and keypad active conditions.

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email [email protected] P:\ INST INSTRUCTIONS\ACCESS CONTROLS\INST-918 REV D 11-21 Page 1

918 EntryCheck TM

Security Door Controls

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

INSTALLATION INSTRUCTIONS

Features

 Keypad programmable

 500 user codes

 1 to 6 digit user codes

 4 independent outputs

 4 independent timers

 2 Form C relay contacts

 2 solid state open collector outputs

 Program entry codes to activate one or both

relays

 Disable input

 Door sense input

 Request-to-exit/enter input

 Keypad tamper lockout

 Timed anti-passback

 Anti-tailgate

 Two LED status indicators

 Tactile key feel

 Audible code entry verification

 12 or 24V, AC or DC operation

SPECIFICATIONS

Mechanical

Dimensions: 3.00" W x 4.75" H x 1.50" D

(.250”D wall extrusion)

Electrical

Input Voltage: 12/24 Volts DC or AC

Operating Current: 30 mA typical, 150 mA max

Output Ratings

Main Relay: Form “C” 5 Amps @ 28 Volts max

Auxiliary Relay: Form “C” 2 Amp @ 28 Volts max

Type: Solid state outputs (Outputs #3 & #4)

Short-to-common 100 mA @ 24 VDC maximum

Environmental

Temperature: -22°F to 149°F (-30°C to 65°C)

Humidity: 5% to 95% non-condensing

P:\ INST INSTRUCTIONS\ACCESS CONTROLS\INST-918 REV D 11-21 Page 2

QuickStart Programming

To enter Programming Mode, enter #9# Master Code#. The yellow indicator will blink slowly showing that the 918 EntryCheck™ is in

programming mode. Use the option codes to program the each function. After the new data entry is complete for each function , the

yellow indicator will flash quickly while the data is being stored and the green indicator will light briefly if the programming has been

accepted. The red indicator will light if any programming data is entered incorrectly or the function is rejected. If a red indicator is seen,

the entire function (option code + data) will have to be fully re-entered.

Test your new user code

Enter user code ‘9876’. After pressing the last digit, the green indicator should illuminate,

and the main relay should activate and the door should unlock for 5 seconds.

KEYPAD

RED/GREEN

POWER/ACCESS

INDICATOR YELLOW

“LOCKOUT/

PROGRAM”

INDICATOR

TERMINAL

BLOCK #1

(TB1)

MOUNTING

PLATE

BEEPER

LEVEL

JUMPER

(JP1)

WIRE

HARNESS

(E1-E8)

MASTER CODE

RESET JUMPER

(JP2)

Fig. 1 Keypad

Program the first user code

Step 1. Enter: #9# 123456# Enter the program mode (default master code = 123456)

Step 2. Enter: 03# 4# Set the entry code length to 4 digits

Step 3. Enter: 21# 5# Set the main relay activate time to 5 sec.

Step 4. Enter: 01# 9876# 9876# 1# Set user code ‘9876’ to activate the main relay

Step 5. Enter: # Exit programming mode

Adding additional user codes

Once the code length and relay time have been set you do not need to set them each

time you additional users.

To add additional users:

Step 1. Enter: #9# 123456# Enter the program mode (default master code)

Step 2. Enter: 01# 2222# 2222# 1# Set user code ‘2222’ to activate the main relay

Step 3. Enter: 01# 3333# 3333# 1# Set user code ‘3333’ to activate the main relay

Step 4. Enter: # Exit programming mode

Deleting a user code

To delete a user:

Step 1. Enter: #9# 123456# Enter the program mode (default master code)

Step 2. Enter: 02# 3333# 3333# User code ‘3333’ has been deleted.

Step . Enter: # Exit programming mode

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

CAUTION

IF THE UNIT IS AC POWERED, MAKE SURE

THAT THE SECONDARY OF THE SYSTEM IS

ISOLATED FROM EARTH GROUND

!!Fig. 2 Wiring Diagram

E1 E2 E3 E4 E5 E6 E7 E8

AUXILIARY RELAY

2 AMPS @ 28VDC MAX

TO POWER SUPPLY

FAIL SECURE CONNECTION

-KEY PAD POWER

12/24 VOLTS

DC or AC

SENSE

GROUND

REQUEST TO EXIT

GROUND

OUTPUT 3

OUTPUT 4

GROUND BLACK

GREEN

BLUE

BLACK

VIOLET

BLACK

GRAY

FAIL SAFE CONNECTION

MAIN RELAY

5 AMPS @ 28VDC MAX

CN/O

N/C

CN/O

N/C

N/C DOOR

POSITION

SWITCH

N/O

REQUEST-

TO-EXIT

SWITCH

EARTH

GROUND

CONNECTION

AUXILIARY OUTPUTS

100mA MAX TO COMMON

918 TERMINALS

COM

COM }

}

P:\ INST INSTRUCTIONS\ACCESS CONTROLS\INST-918 REV D 11-21 Page 3

KEYPAD WIRING

See Fig. 3 for an example of a typical door installation. The keypad is

mounted adjacent to the door. A fail-secure electric door strike is

mounted in the door jamb to release the door lock. A door contact switch

is mounted on top of the door jamb for detecting when the door is open.

Use the following steps to wire the keypad. Refer to the wiring diagram

shown in Fig. 4 to assist in the wiring.

Note: Up to 300 feet of 18 AWG wire can be run for power, use larger

wire for longer runs. Use 22 AWG or larger (depending on load) for other

connections.

Relay Output

 Install a low voltage electric door strike for unlocking the door.

 Route two wires between the door strike and the keypad box.

Connect the (+) door strike wire to the keypad’s MAIN RELAY N.O.

terminal (TB1 #3). Connect the other door strike wire to the

keypad’s AC/DC (-) terminal (TB1 #2). Connect a wire between the

keypad’s AC/DC (+) terminal (TB1 #1) and the MAIN RELAY COM

terminal

(TB1 #4).

Keypad Power

 Choose a location for the power supply or transformer.

 Route two wires between the door strike and the keypad box.

Connect the power supply’s output terminals to the keypad’s AC/DC

input terminals (TB1 #1 (+) & #2(-)). Observe wiring polarity if using

DC.

Caution: If the unit is AC powered, make sure the secondary

of the system transformer is isolated from earth ground.

Earth Ground

 To avoid damage to the unit from static discharges, connect the

EARTH GROUND black wire E5 to a good earth grounding point.

Suggested wiring size is 18 AWG for earth ground.

Sense Input

Note: SENSE terminal E8 (gray wire) can be programmed for either a

door sense or inhibit input. Both features cannot be used at the same

time.

 To use the door sense feature to detect forced entry or door ajar

conditions, install a normally closed door switch on the door and

route two wires from the switch to the keypad box. Connect the door

switch to the keypad’s SENSE terminal (gray wire E8) and COM

terminal

 If an inhibit switch or timer is going to be used for temporarily

disabling the keypad, route two wires from the switch or timer to the

keypad box. Connect the inhibit switch/timer normally open

terminals to the keypad’s SENSE (gray wire E8) and COM terminal

(any available black wire).

Request-to-Exit Input (wiring shown on Fig. 4)

 If a request-to-exit pushbutton is going to be used, route two wires

from the keypad box to a normally open pushbutton mounted on the

secure side of the door. Connect the wires to the pushbutton and to

the keypad’s REX (violet wire E6) and COM terminal (any available

black wire).

Solid State Outputs

The two solid state outputs (Outputs #3 & #4) can be programmed to

activate during various conditions. These outputs can be used to activate

indicators or sounders. See fig. 5 for wiring examples using the solid

state outputs.

Fig. 5 Using Solid State Outputs

OUTPUT #3 LIGHTS AN LED

OUTPUT #4 LIGHTS AN LED AND SOUNDS A BEEPER

EXAMPLE #1:

POWER

SUPPLY +

LED

BLUE

GREEN

1KΩ

OUTPUT #3

OUTPUT #4

ELECTRONIC

BEEPER

OUTPUT #3 LIGHTS A LAMP POWERED FROM AN EXTERNAL SOURCE

OUTPUT #4 TRIGGERS A NORMALLY OPEN ALARM PANEL ZONE

EXAMPLE #2:

BLUE

GREEN

OUTPUT #3 COM

OUTPUT #4 COM

POWER

SOURCE

OUTPUT #3

END OF LINE

RESISTOR ALARM PANEL

NO ZONE

COMMON

LOW

VOLTAGE

LAMP

BLACK

OUTPUT #4

EACH

OUTPUT

100 mA

MAXIMUM

Wire

Pigtail

Wire

Pigtail

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

Fig. 4 Basic Door Installation Wiring

GRAY

BLACK

BLUE

GREEN

VIOLET C

NC DOOR

POSITION SWITCH

NO REQUEST-TO-

EXIT SWITCH

SENSE

GROUND

REQUEST-TO-EXIT

GROUND

OUTPUT

EARTH

GROUND

CONNECTION

WIRES

E1 E2 E3 E4 E5 E6 E7 E8

TB1

12/24 VOLTS

DC or AC

COM

MAIN RELAY –

5 AMPS @ 28 VDC MAX

AUXILIARY RELAY

2 AMPS @ 28 VDC MAX

FAIL SAFE CONNECTION

FAIL SECURE CONNECTION

TO POWER SUPPLY

12345678

P:\ INST INSTRUCTIONS\ACCESS CONTROLS\INST-918 REV D 11-21 Page 4

FACTORY DEFAULTS

Master Programming Code………..……………….….…...123456

Entry Code Length…………………………………….……..4 digits

Request-to-exit Output Relay…………………….........Main Relay

Alarm Shunt Output….……………………………….........Disabled

Forced Entry Output………………………….…………..No Output

Door Ajar Output………………………………..………...No Output

Main Relay On Time……………………….……...……..2 Seconds

Auxiliary Relay On Time…………………….………...…2 Seconds

Solid State Output #3 On Time……………….……..….2 Seconds

Solid State Output #4 On Time……………….………...2 Seconds

Door Sense/Inhibit Input………………………....….....Door Sense

Keypad Lockout Output………………………….…..…….Disabled

Keypad Active Output……………………………….....…..Disabled

Beeper Sounds When Key Pressed………………..……..……Yes

Beeper Sounds During Relay #1……………………....……..….No

Beeper Sounds During Relay #2…………………………....…...No

Beeper Sounds During Output #3……………...……………......No

Beeper Sounds During Output #4……………………….…........No

Keypad Lockout Count……….………...….3 Tries Before Lockout

Keypad Lockout Time..………......…….....…....60 seconds (fixed)

Anti-Passback Time………………..…...……….No Anti-Passback

Auto-Relock………………………………….….…On Door Closure

BASIC PROGRAMMING

When the 918 EntryCheck™ is in Programming Mode, the

yellow indicator will blink slowly. This shows that the 918 is

ready to accept new programming data. Use the programming

commands on the following three pages to enter new data.

After a data entry command is complete, the yellow indicator will

flash rapidly while the data is being stored. The green indicator

will light if the data is accepted. The red indicator will light if any

programming data is entered incorrectly, and the command will

have to be fully re-entered.

Entering Programming Mode

The 6-digit Master Programming Code (default = 123456) is

used to enter Programming Mode.

Press: # 9 # Master Code#

Master Code = the current 6-digit Master Programming Code

Exiting Programming Mode

Press: * * #

The red indicator will light after exiting Programming Mode

Note: The 918 will automatically exit Programming Mode after

two minutes of inactivity

Re-entering a Command After a Mistake

If the red indicator lights, signaling an incorrect entry, or an

incorrect key is pressed during programming, to clear the

keypad and re-enter the command:

Press: * 9 #

Setting Entry Code Length Default: 4 digits

Press: 0 3 # Length #

Length = 1-6 for entry code length

Note: If the Entry Code Length is going to be changed from the factory

default of 4 digits, make this change first before programming any entry

codes.

Adding a New Entry Code

Press: 0 1 # Code # Code # Relay #

Code=The new entry code: 1-999999, depending on code length

Relay=Relay output entry code will activate:

1=Main Relay 2=Auxiliary Relay 3=Both Relays

10=Relay #1, toggled 20=Relay #2, toggled 30=both Relays toggled

12=Relay #1 toggled; Relay #2 timed open

21=Relay #1 timed open; Relay #2 toggled

The yellow indicator will flash quickly while the 918 searches its

memory for available space and duplicate entries. The green

indicator will light when the new code is stored.

If the new entry code chosen is already being used for another entry

code, the red indicator will light. A new unique code needs to be

entered.

Note: Leading zeros (zeros before the code number, i.e.0001) do not need to

be entered when programming a new code. The 918 will internally add any

zeros to fill digits determined by the entry code length setting. Leading zeros

will have to be entered by the user when entering their code to gain access.

Changing the 6-Digit Master Programming Code

Press: 9 8 # Master Code # Master Code #

Master Code=The new 6-digit Master Programming Code

New master code: ____________

Typical Programming Example

Program all normal entry codes to use the Main Relay (Relay #1),

and only Relay #1 as the output relay. See the following example

that sets entry codes 1234 for normal, timed entry and 5678 for

toggle operation.

Press: 0 1 # 1 2 3 4 # 1 2 3 4 # 1 #

01=Programming Step; 1234=Entry Code; 1=Main Relay

Press: 0 1 # 5 6 7 8 # 5 6 7 8 # 10 #

01=Programming Step; 5678=Entry Code; 10=Toggle Main Relay

Programming the 918 To Hold the Output for an Extended Period of

Time (e.g., Normal Business Hours)

SDC’s EntryCheck™ products have a programmable “Toggle

Mode” available for each relay. When an output is programmed for

Toggle Mode, the output alternates from OFF to ON or from ON to

OFF each time it is activated. When output is toggled on, the

green LED flashes until toggled off.

The rules for a toggle output are:

If the output is OFF, entering a toggle code will turn ON

the selected relay, and stay on until the next activation of a toggle

code. NOTE: Entering a timed code OR activating the REX input

will not turn off a relay that has been toggled ON.

If the output is ON, entering a toggle code will turn OFF

the selected relay and stay off until the next activation of a toggle

code, timed code, or REX.

Erasing a Single Entry Code

Press: 0 2 # Code # Code #

Code=The entry code to delete

The yellow indicator will flash quickly while the 918 searches its

memory for the code to erase. The green indicator will light when

the code is erased.

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

Select Door Sense or Inhibit Input Default: Door Sense

The input (gray wire) can be programmed for DOOR SENSE or

INHIBIT.

Press: 1 0 # Input #

Input=0 for Door Sense; =1 for Inhibit

When programmed for DOOR SENSE, if an open condition on

the input occurs before access is granted (with an entry code or

with the request-to-enter input) a FORCED ENTRY output will

occur. If an open condition remains beyond the door ajar time

following a valid relay activation for access, a DOOR AJAR

output will occur.

When programmed for INHIBIT, a closed condition on the input

will prevent Relay #1 from activating when access is requested

with an entry code. This mode is typically used with an

external timer to disable the access device at certain times.

Select Forced Entry Output Default: No Output

Sets which output activates if the DOOR SENSE input opens

before authorized access is granted. This output is not timed.

The selected relay latches ON, until any valid code (timed or

toggled) is entered.

Press: 1 1 # Output #

Output=Output to Activate(0-4)

1=Main Relay; 2=Auxiliary Relay; 3=Output #3; 4=Output #4;

0=No Output

Select Door Ajar Output Default: No Output

Sets which output activates if the DOOR SENSE input stays

open beyond the door ajar time, after access is granted (door

ajar time is adjustable using Function 25 on next page). This

output is not timed. When the DOOR SENSE input returns to

normal, the output turns off.

Press: 1 2 # Output #

Output=Output to Activate (0-4)

1=Main Relay; 2=Auxiliary Relay; 3=Output #3; 4=Output #4;

0=No Output

ADDITIONAL PROGRAMMING OPTIONS

There are several 918 EntryCheck™ programming options. For

most installations, the basic programming on the previous page

is sufficient.

Erasing All Entry Codes

WARNING: PERFORMING THIS COMMAND WILL REMOVE

ALL ENTRY CODES FROM THE MEMORY. THE MASTER

CODE WILL NOT BE RESET.

Press: 9 7 # 0 0 0 0 0 0 # 0 0 0 0 0 0 #

Note: The green indicator will light while the memory is being erased.

This may take up to 15 seconds.

Select Keypad Active Output Default: No Output

Sets which output activates when any keys are pressed. This

output is timed. If toggle mode is selected for the output, the timer

value defaults to 2 seconds.

Press: 1 4 # Output #

Output=Output to Activate(0-4)

1=Main Relay; 2=Auxiliary Relay; 3=Output #3; 4=Output #4;

0=No Output

Select Keypad Lockout Output Default: No Output

Sets which output activates when the keypad is “locked out” after

too many incorrect entry code attempts. The lockout time is 60

seconds.

Press: 1 3 # Output #

Output=Output to Activate (0-4)

1=Main Relay; 2 = Auxiliary Relay; 3=Output #3; 4=Output #4;

0=No Output

Select Alarm Shunt Output Default: No Output

Sets which output activates during the time access is granted.

(Use this output ot shunt alarm contacts attached to the access

door.) This output may be timed or toggled.

Press: 1 5 # Output #

Output=Output to Activate(0-4)

1=Main Relay; 2=Auxiliary Relay; 3=Output #3; 4=Output #4;

0=No Output

Select Request-to-Exit Output Default: Main Output

Sets which output activates when the Request-to-Exit input is

grounded.

Press: 1 6 # Output #

Output=Output to Activate(0-4)

1=Main Relay; 2=Auxiliary Relay; 3=Output #3; 4=Output #4;

0=No Output

Main Relay On-time Default: 2 Seconds

Sets the length of time the Main Relay activates when triggered.

Green LED is on when Main Relay is active.

Press: 2 1 # Seconds #

Seconds=Output time in seconds (0-60)

Auxiliary Relay On-time Default: 2 Seconds

Sets the length of time the Auxiliary Relay activates when triggered.

Press: 2 2 # Seconds #

Seconds=Output time in seconds (0-60)

Solid-state Output #3 On-time Default: 2 Seconds

Sets the length of time Output #3 activates when triggered.

Press: 2 3 # Seconds #

Seconds=Output time in seconds (0-60)

P:\ INST INSTRUCTIONS\ACCESS CONTROLS\INST-918 REV D 11-21 Page 5

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

Beep Sounds During Auxiliary Relay Default: No

Selects whether or not the keypad beeps during Auxiliary Relay

activation.

Press: 4 2 # Sound #

Sound=1 for Yes, =0 for No

Beep Sounds During Output #3 Default: No

Selects whether or not the keypad beeps during Output #3

activation.

Press: 4 3 # Sound #

Sound=1 for Yes, =0 for No

Beep Sounds During Output #4 Default: No

Selects whether or not the keypad beeps during Output #4

activation.

Press: 4 4 # Sound #

Sound=1 for Yes, =0 for No

Beep Sounds During Main Relay Default: No

Selects whether or not the keypad beeps during Main Relay

activation.

Press: 4 1 # Sound #

Sound=1 for Yes, =0 for No

Solid-state Output #4 On-time Default: 2 Seconds

Sets the length of time Output #4 activates when triggered.

Press: 2 4 # Seconds #

Seconds=Output time in seconds (0-60)

Beep Sounds on Keystrokes Default: Yes

Selects whether or not the keypad beeps as each key is pressed.

Press: 4 0 # Sound #

Sound=1 for Yes, =0 for No

Door Ajar Timer Default: 60 Seconds

Sets the amount of time the door may be held open after an

authorized access. The DOOR AJAR output will activate after

the time expires.

Press: 25 # Seconds #

Seconds=Held open time in seconds (1-60)

Keypad Lockout Count Default: 3 Tries

Sets the number or incorrect entry code attempts allowed

before the keypad “locks out”.

Press: 5 0 # Attempts #

Attempts=Number of attempts before lockout (2-7)

Anti-Pass Back Time Default: No Anti-Pass Back

Sets the length of time an entry code will not function after it is

used.

Press: 5 1 # Minutes #

Minutes=Time in minutes (1-4), 0=No Anti-passback

RESETTING KEYPAD

Master Reset

CAUTION: Performing a master reset will clear the

entire memory of the 918 and return all programmable

options to the factory default values. ALL ENTRY

CODES WILL BE ERASED.

STEP 1 Disconnect power from the keypad.

STEP 2 Press and hold down the * and # keys.

STEP 3 Apply power to the keypad, continue holding the keys

down until the red indicator starts flashing

STEP 4 Release the keys. The red and yellow indicators will

remain lit until the process is complete, then the

yellow indicator will go out.

Resetting the Master Code

STEP 1 Remove the 918 from the wall..

STEP 2 Locate jumper at JP2. This jumper is used to reset

the master code.

STEP 3 With power applied to the keypad, remove the jumper

at JP2. The keypad will begin to beep, signaling that

the code has been reset.

STEP 4 Replace jumper on JP2

THE MASTER PROGRAMMING CODE IS NOW 123456.

Beeper Sound Level

The Keypad’s beeper can be set to high or low level.

Remove jumper JP1 to reduce beeper sound level.

Selects mode for Keypad LED Backlight Default: 30 Seconds

Selects whether or not the keypad back light stays OFF, lights for

30 seconds when activated or stays ON.

Press: 52 # Output #

0 = Light always OFF

1 = 30 sec light when activated (default)

2 = Light always ON

P:\ INST INSTRUCTIONS\ACCESS CONTROLS\INST-918 REV D 11-21 Page 6

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

Indice

Altri manuali SDC Serratura della porta

Manuali Serratura della porta popolari di altre marche

Assa Abloy

Assa Abloy effeff 827A-IP Manuale utente

We.lock

We.lock SECBNEBL51 Manuale utente

Iseo

Iseo MA1A Manuale utente

ID Lock

ID Lock 150 Manuale utente

Lockly

Lockly ACCESS TOUCH PRO Manuale utente

iLoq

iLoq G50S Manuale utente

ilco

ilco 452 Manuale utente

Samsung

Samsung shs-h705 Manuale utente

TRU-BOLT

TRU-BOLT 08102017 Manuale utente

CDVI

CDVI 500-LADJ Manuale utente

Igloohome

Igloohome Deadbolt 2S Metal Grey Istruzioni di installazione e manutenzione

eSSL

eSSL FL-300 Manuale utente

JAKO

JAKO JKBTNX4 Manuale utente

Dorma

Dorma MUNDUS PREMIUM GK 50 Guida utente

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuale utente

Yale

Yale MORTISE 8800 SERIES Manuale utente

Siegenia

Siegenia KFV AS3500 Manuale utente

Saflok

Saflok Quantum ädesē RFID Manuale utente