SeaLevel ACB-ULTRA.LPCI Manuale utente

ACB-ULTRA.LPCI

User Manual | 5104

Contents

CONTENTS...........................................................................................................................................................2

INTRODUCTION ...................................................................................................................................................3

BEFORE YOU GET STARTED ...............................................................................................................................4

SOFTWARE INSTALLATION ................................................................................................................................6

HARDWARE INSTALLATION ............................................................................................................................... 7

TECHNICAL DESCRIPTION .................................................................................................................................8

SPECIFICATIONS ...............................................................................................................................................17

APPENDIX A –TROUBLESHOOTING................................................................................................................18

APPENDIX B –HOW TO GET ASSISTANCE .....................................................................................................19

APPENDIX C –ELECTRICAL INTERFACE ........................................................................................................20

APPENDIX D –SILK SCREEN –5104 PCB.......................................................................................................22

APPENDIX E –COMPLIANCE NOTICES...........................................................................................................23

WARRANTY ........................................................................................................................................................24

Introduction

The ACB-ULTRA.LPCI adapter provides the PC with a single channel high-speed multi-protocol serial

interface suitable for the most popular communication protocols. This sync/async card provides an ideal

solution for high-speed applications including LAN/WAN connectivity. Utilizing the Zilog Z16C32 (IUSC™)

on chip DMA controller eliminates bus bandwidth constraints that are placed on typical interface adapters,

allowing data rates to reach 10M bps in burst mode. By utilizing the Z16C32's 32 byte FIFO buffer coupled

with 256K of on board memory, higher data rates are achieved.

The ACB-ULTRA.LPCI meets the PCISIG size requirements for an MD1 Low Profile adapter. This allows the

ACB-ULTRA.LPCI to be used in a variety of modern systems, including low profile servers, network

appliances and ‘All in One’ desktop computers. A standard height bracket is available for implementations

in a standard height PCI slot. The ACB-ULTRA.LPCI is a ‘Universal Bus’ adapter, allowing for use in either

+5 or +3.3V PCI slots and provides compliance with the PCISIG PCI Bus Specification Revision 2.2/2.3,

which requires ATX power support for both 5V and 3.3V.

Other Sealevel Sync Products

PC/104

ACB-104 (P/N 3512) - Z85230 RS-232/422/485/530/530a/V.35

ACB-104.ULTRA (P/N 3514) - Z16C32 RS-232/422/485/530/530a/V.35

Low Profile PCI

ACB-MP.LPCI (P/N 5102) - Z85230 RS-232/422/485/530/530a/V.35

ACB-232.LPCI (P/N 5103) - Z85230 RS-232

PCI

ACB-MP.LPCI (P/N 5102S) - Z85230 RS-232/422/485/530/530a/V.35

ACB-232.LPCI (P/N 5103S) - Z85230 RS-232

PCMCIA

PC-ACB-MP (P/N 3612) - Z85233 RS-232/422/485/530/530a/V.35

Before You Get Started

What’s Included

The ACB-ULTRA.LPCI is shipped with the following items. If any of these items is missing or damaged,

please contact Sealevel for replacement.

•ACB-ULTRA.LPCI Adapter

•5104 includes low profile PCI bracket

•5104S includes standard size PCI bracket

Advisory Conventions

Warning

The highest level of importance used to stress a condition where damage could result to the

product, or the user could suffer serious injury.

Important

The middle level of importance used to highlight information that might not seem obvious or a

situation that could cause the product to fail.

Note

The lowest level of importance used to provide background information, additional tips, or other

non-critical facts that will not affect the use of the product.

Optional Items

Depending upon your application, you are likely to find one or more of the following items useful for

interfacing the ACB-ULTRA.LPCI to real-world signals. All items can be purchased from our website

(http://www.sealevel.com) or by calling 864-843- 4343.

Part No.

Description

CA-178

6’ shielded cable with a DB-25F connector to an ITU-T ISO-2593 style connector (V.35) and converts

the Sealevel DB-25 implementation to the ITU-T V.35 mechanical standard.

CA-104

6’ extension cable with one DB-25M connector and one DB25Fconnector, pinned one-to-one, for use

with RS-232 and RS-530.

CA-107

10” shielded cabling adapter with a DB-25F (RS-530) to a DB-37M (RS-449 DTE). RS-530 is replacing

RS-449 in Telecom applications, but there is still a very large installed base of equipment that still

uses the RS-449 pin-out. Both standards use RS-422 to define the electrical specifications and are

interchangeable via this adapter cable.

CA-159

6’ shielded cable with a DB-25F (RS-530) to a DB-15M (X.21) and converts the standard DB-25

implementation of RS-530 or RS-422 to the ITU-T X.21 standard.

Software Installation

Windows 2000/XP Installation

Do not install the adapter until the software has been successfully installed. .

1. Begin by locating, selecting, and installing the correct software from the Sealevel software driver

database.

2. Select the Part Number (5104) for your adapter from the listing. Select ‘Download Now’ for the

version of SeaMAC software (Route56 for Linux v2.0.10).

3. The setup file will automatically detect the operating environment and install the proper

components. Next (depending on the OS version) select the ‘Run this program from its current

location’ or ‘Open’ option. Follow the information presented on the screens that follow.

4. A screen may appear with the declaration: “The publisher cannot be determined due to the

problems below: Authenticode signature not found.” Please select the ‘Yes’ button and proceed

with the installation. This declaration simply means that the Operating System is not aware of the

driver being loaded. It will not cause any harm to your system.

5. During setup, the user may specify installation directories and other preferred configurations. This

program also adds entries to the system registry that are necessary for specifying the operating

parameters for each driver. An uninstall option is also included to remove all registry/INI file entries

from the system.

Hardware Installation

The adapter can be installed in any PCI (5V or 3.3 V) expansion slot.

Do not install the Adapter in the machine until the software has been fully installed.

1. Turn off power. Disconnect the power cord.

2. Remove the PC case cover.

3. Locate an available PCI slot and remove the blank metal slot cover.

4. Gently insert the PCI adapter into the slot. Make sure that the adapter is seated properly.

5. Replace the screw. (This is required to ensure FCC Part 15 compliance.)

6. Replace the cover.

7. Connect the power cord and power up the machine.

The ACB-ULTRA.LPCI is now ready for use.

Technical Description

The ACB-ULTRA.LPCI adapter was designed for seamless integration into any PCI based system. The ACB-

ULTRA.LPCI adapter requires a PCI slot, one IRQ, an 8 byte block of I/O address and a 16K block or 256K

block of memory address and additionally, the IUSC requires a 256 byte block of memory. The memory

range of this adapter can be configured to reside in the lower 1 Megabyte memory only or anywhere in

upper memory. Low memory (not available on PCI 2.2 or higher systems) must be configured as 16 X 16K

blocks of page memory. High memory can be configured as a 256K linear block or 16K paged memory.

Features

•Single channel high speed sync/async wide area network (WAN) interface

•RS-232, RS-422/449, EIA-530, V.35 and RS-485 serial interface capability with versatile cabling

options

•Multi-protocol capable including PPP (point-to-point protocol), Frame Relay, X.25, high-speed

Async, Bi-Sync, Mono-Sync, HDLC, SDLC, etc.

•Ideal for T1, Fractional T1, E1, and ISDN and other WAN applications

•On-board Z16C32 (IUSC™) with built in DMA controller and 32 byte FIFO buffer

•Up to 10 Mbps burst mode

•256K of on-board RAM

•Link list DMA supported

•32-bit data path

•OEM Security feature available as an option

Z16C32 IUSC™

The ACB-ULTRA.LPCI is based on a single Zilog Z16C32 IUSC (Integrated Universal Serial Controller). The

IUSC has a built-in DMA controller that allows high-speed data transfers directly to and from the 256K block

of on-board memory. The IUSC’s built-in DMA controller supports 4 different modes of DMA transfer: Single

Buffer, Pipelined, Array, and Link List. An on-board 20MHz oscillator clocks the IUSC.

Technical Description, Continued

RAM

The memory window is located by BIOS PCI setup or the Set PCI function. The window size is a 16K paged

or 256K linear block. In paged mode the registers are located in the I/O registers.

•Low Memory options: 16 pages of 16K memory blocks totaling 256K (not available on PCI 2.2 or

later systems).

•High Memory options: 16 pages of 16K memory blocks totaling 256K or one linear block of 256K

memory.

Control and Status Registers Defined

The control and status registers occupy 8 consecutive locations. The following tables provide a functional

description of the bit positions.

Address

Mode

Base+0

{0}

{1}+

P17

P16

P15

P14

Base+0

ACCEN

MEM/IUC

P17

P16

P15

P14

Base+1

{0}

Base+1

Base+2

LIN/PAGED

{0}

{1}

{0}

Base+2

LIN/PAGED

Base+3

{0}

INTPEND

RESTAT

{1}

{0}

Base+3

SW Board Reset

Base+4

{0}

IRQEN

{0}

Base+4

IRQEN

Base+5

{0}

Base+5

Base+6

SD7

SD6

SD5

SD4

SD3

SD2

SD1

SD0

Base+7

SD15

SD14

SD13

SD12

SD11

SD10

SD9

SD8

X = do not care { }= always this value

Technical Description, Continued

Control and Status Name Definition

Field

Description

ACCEN

1 = Host access to RAM or IUSC enabled; 0 = Host access to RAM or IUSC disabled. (0 on power-up)

MEM/IUC

1 = Enable Host access to RAM; 0 = Enable Host access to IUSC. (0 on power-up)

P17-P14

These bits select which of sixteen 16K RAM pages is visible at the address selected by MA18-MA14.

IRQEN

1 = Interrupts enabled, 0 = Interrupts disabled. (0 on power-up)

INTPEND

IUSC interrupt status: 1 = No interrupt pending on IUSC; 0 = Interrupt pending on IUSC.

RESTAT

Reset status: 1 = On-board reset inactive; 0 = On-board reset active.

Remote loopback

Local loopback

M0-M3

I/O mode select to SP505 (all 0 on power-up)

See Interface Selection table for valid interface options

SD0-SD15

Optional security feature. Unique value per customer or application. (default value = FFFF)

LIN/PAGE

1=256K linear block in high memory only, 0=16X16K pages in low or high memory, (0 on power-up)

Interface Selection

The ACB-ULTRA.LPCI supports a variety of electrical interfaces. Reference the Control and Status Registers

Defined section of this manual for this bit description. There is line termination on RXD, RXC, and TXC in

the following modes: RS-530, RS-530A, RS-485T, and V.35.

Reset Circuit

Writing any value to base+3 will reset the Z16C32. Only one write is required. This starts a reset sequence,

which lasts about 320 ns. During the reset sequence base+3 bit D4 will read 0. When the reset is complete,

base+3 bit D4 will read 1.

The Z16C32 should not be accessed until the reset sequence is complete.

TSET Clock Select

Port5 of Z16C32 is used to select TSET clock source.

•0 selects 16C32 TXC as source

•1 selects received TXC as source

Indice

Altri manuali SeaLevel Hardware per computer

SeaLevel

SeaLevel Ultra COMM+2.PCIe 7205ec Manuale utente

SeaLevel

SeaLevel ACB II 3061 Manuale utente

SeaLevel

SeaLevel Route 56 Manuale utente

SeaLevel

SeaLevel ISO-16 Manuale utente

SeaLevel

SeaLevel DuoCom Manuale utente

SeaLevel

SeaLevel PC-ACB.MP Manuale utente

SeaLevel

SeaLevel DIO-16.LCPI Manuale utente

SeaLevel

SeaLevel REL-32 Manuale utente

SeaLevel

SeaLevel SeaLINK/PC.SC Manuale utente

SeaLevel

SeaLevel SIO4-104.485 Manuale utente

SeaLevel

SeaLevel DIO-32.PCIe Manuale utente

SeaLevel

SeaLevel 7802e Manuale utente

SeaLevel

SeaLevel SeaPORT REL-16 Manuale utente

SeaLevel

SeaLevel DIO-16.LPCIe Manuale utente

SeaLevel

SeaLevel COMM+4/422.PCIe Manuale utente

SeaLevel

SeaLevel Ultra 530.LPCIe Manuale utente

SeaLevel

SeaLevel SeaLINK+232.PC Manuale utente

SeaLevel

SeaLevel SeaPORT DIO-16 Manuale utente

SeaLevel

SeaLevel 7202e Manuale utente

SeaLevel

SeaLevel Ultra-SIO 3089 Manuale utente

SeaLevel

SeaLevel C4-104 Series Manuale utente

SeaLevel

SeaLevel ACB-MP.LPCI Manuale utente

SeaLevel

SeaLevel COMM+2 Manuale utente

SeaLevel

SeaLevel SeaLINK +2.SC Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente