SeaLevel C4-104.ULTRA Manuale utente

C4-104.ULTRA

User Manual | 3541

Contents

CONTENTS...........................................................................................................................................................2

INTRODUCTION ................................................................................................................................................... 3

BEFORE YOU GET STARTED ............................................................................................................................... 4

CARD SETUP ........................................................................................................................................................5

INSTALLATION ....................................................................................................................................................9

PHYSICAL INSTALLATION................................................................................................................................10

TECHNICAL DESCRIPTION ...............................................................................................................................11

SPECIFICATIONS ...............................................................................................................................................12

APPENDIX A – TROUBLESHOOTING................................................................................................................13

APPENDIX B – HOW TO GET ASSISTANCE .....................................................................................................14

APPENDIX C – ELECTRICAL INTERFACE ........................................................................................................15

APPENDIX D – ASYNCHRONOUS COMMUNICATIONS ..................................................................................16

APPENDIX E – SILK SCREEN ............................................................................................................................17

APPENDIX F – COMPLIANCE NOTICES...........................................................................................................18

WARRANTY ........................................................................................................................................................19

................................................................................................................................................................................

Introduction

Overview

The C4-104.ULTRA provides a PC/104 serial interface module with four software-selectable RS-

232/422/485 ports. RS-232, RS-422, or RS-485 mode may be selected independently via software

command for each of the four ports, eliminating the need for setting jumpers or DIP-switches. The board

is designed using the XR16C864 UART, which provides a 128-byte FIFO, 8 times larger than boards

designed with 16C550 compatible parts. The larger buffers allow error free operation even in high-speed

applications. In RS-485 mode the C4-104.ULTRA offers automatic control of the RS-485 driver enable for

trouble free network master arbitration. Additionally, the C4-104.ULTRA allows RS-485 network

termination, critical to robust multi-drop communication, to be selectively added to the circuit via a simple

software command.

The RS-232 compatibility allows for connection to devices utilizing the RS-232 electrical interface, such as

modems, data-entry terminals, and plotters.

RS-422 provides excellent communications for long distance device connections up to 4000ft., where noise

immunity and high data integrity are essential.

RS-485 is optimized for ‘Multi-Drop’ or ‘Party-line’ operations selecting data from multiple peripherals (as

many as 31 devices can be connected on an RS-485 bus). The C4-104.ULTRA is optimized for RS-485 with

automatic driver enable, and automatic suppression of RS-485 ‘Echo’ as options, further simplifying

integration.

Factory Default Settings

The SIO-104 factory default settings are as follows:

Base

Address

IRQ

Port 1

280

Before You Get Started

What’s Included

The C4-104.ULTRA is shipped with the following items. If any of these items is missing or damaged,

contact the supplier.

C4-104.ULTRA Serial I/O Adapter

Advisory Conventions

Warning

The highest level of importance used to stress a condition where damage could result to the

product, or the user could suffer serious injury.

Important

The middle level of importance used to highlight information that might not seem obvious or a

situation that could cause the product to fail.

Note

The lowest level of importance used to provide background information, additional tips, or other

non-critical facts that will not affect the use of the product.

Card Setup

The C4-104.ULTRA contains two DIP-Switches and a jumper strap for each port, which must be set for

proper operation.

Address Selection

Each port on the C4-104.ULTRA occupies sixteen consecutive I/O locations. A DIP-switch is used to set

the base address for these locations. The following table shows the addressing options available. If

different address options are required, please contact Sealevel Systems Technical Support about a custom

PAL option.

SW1-1

SW1-2

SW1-3

Port

Port 4

OFF

300

310

320

330

OFF

400

410

420

430

OFF

500

510

520

530

OFF

600

610

620

630

OFF

1500

1510

1520

1530

OFF

3220

3230

3240

3250

4220

4230

4240

4250

Figure 1 - Address Selection Table

Refer to Appendix A for common address contentions.

Port Enable / Disable

All four ports on the can be enabled or disabled by setting the three switches in the ‘Off’ position. The port

is enabled when a valid I/O selection is made. If the adapter is disabled, be sure to disable the interrupt

request by removing the IRQ jumper.

Interrupt Modes

DIP-Switch positions ‘S’ and ‘M’ on switch SW1 selects the interrupt mode for the adapter.

With the ‘S’ selected, the adapter is in a (S)hared interrupt mode, which allows more than one adapter to

access a single IRQ. Any two or more PC-104 adapters can share a common IRQ by placing the jumpers on

the same IRQ setting and setting the appropriate selections for interrupt mode.

‘M’ indicates the inclusion of a 1K-ohm pull-down resistor required on one adapter when sharing interrupts.

Set the switch to ‘S’ for shared interrupt mode on all adapters sharing an IRQ. On one of the adapters sharing

an interrupt set the switches for both ‘S’ and for ‘M’. This provides the pull-down resistor circuit that makes

sharing IRQs possible. If you are using more than one compatible adapter in a bus, you should only have

one port set to ‘M’.

Header E1 (IRQ Selection)

The C4-104.ULTRA has a single interrupt selection jumper for all four of the ports, which should be set

prior to use, if an interrupt is required by your application software. Consult the user manual for the

application software being used to determine the proper setting.

Figure 2 - Header E1, IRQ Selection (IRQ 3 shown selected)

Clock Modes

The C4-104.ULTRA utilizes a 14.7456 MHz oscillator. This is eight times faster than the standard COM:

port oscillator, which typically is 1.8432 MHz. This allows the adapter to achieve a maximum data rate of

921.6Kbps. The following sections outline the baud rate calculations and instructions for achieving your

desired baud rate.

Baud Rates and Oscillator value

The following table shows some common data rates and the rates you should choose to achieve them

when using the C4-104.ULTRA. If the O/S of choice is Windows 95/98/ME/2000/NT/XP, the oscillator

value (14.7456 MHz) should be entered into the ‘Advanced Tab’ on 95/98/Me/2000/XP Device Manager

applet. Typically this is done automatically when the Sealevel Software driver is loaded.

When using Windows NT, the ‘Advanced Ports’ applet in the Control Panel should be launched and the

oscillator value entered manually in the ‘Advanced’ tab, or all data rates will be eight (8) times the selected

rate. For example if a data rate of 19.2Kbps is selected, the actual data rate will be 153.6Kbps.

3457910111215

When using any other OS (i.e. Linux, or QNX) the following tables should be used.

For this Data Rate

Choose this Data Rate

1200 bps

150 bps

2400 bps

300 bps

4800 bps

600 bps

9600 bps

1200 bps

19.2K bps

2400 bps

57.6 K bps

4800 bps

115.2 K bps

14.4K bps

230.4K bps

28.8K bps

460.8K bps

57.6 K bps

921.6K bps

115.2 K bps

If your communications package allows the use of Baud rate divisors, choose the appropriate divisor from

the following table:

For this Data Rate

Choose this Divisor

1200 bps

768

2400 bps

384

4800 bps

192

9600 bps

19.2K bps

38.4K bps

57.6K bps

115.2K bps

230.4K bps

460.8K bps

921.6K bps

Programmable Features

Each of the ports on the C4-104.ULTRA can be individually configured as an RS-232, RS-422, or RS-485

interface. This is a software selectable feature. Electrical Interface selection (RS-232/422/485), RS-

422/485 termination, and RS-485 ‘Echo’ control are selected via the ‘Control’ port (Base + 8). If the Sealevel

Software Windows drivers are used, this is accomplished as a function of the Device Manager.

Power up default (D3-D0 = 0) = RS-485 (tri-stated) without termination.

Control Word Written to

Base +8

Echo

422/485

Termination

Mode

Hex

RS-232

RS-422 no termination

RS-422 with termination

RS-485 no termination no echo

RS-485 no termination with echo

RS-485 with termination no echo

RS-485 with termination with echo

Line Termination

Typically, each end of the RS-485 bus must have line-terminating resistors (RS-422 terminates at the receive

end only). One of the unique features of the C4-104.ULTRA is its ability to select this termination via a

control word in the control port. It is completely software selectable, thus reducing the complexity of

cabling typically found in RS-485 implementations. Typically a 120-ohm resistor is across each RS-422/485

input in addition to a 1K-ohm pull-up/pull-down combination that biases the receiver inputs. The C4-

104.ULTRA mimics this typical termination electrically. If multiple C4-104.ULTRA adapters are configured

in an RS-485 network, only the boards on each end should have the termination in place.

RS-485 ‘Echo’

The RS-485 ‘Echo’ is the result of connecting the receiver inputs to the transmitter outputs. Every time a

character is transmitted; it is also received. This can be beneficial if the software can handle echoing (i.e.

using received characters to throttle the transmitter) or it can confuse the system if the software does not.

An RS-485 ‘No Echo’ option is selected by writing the correct control word to the control port.

Installation

Software Installation

Windows Installation

Do not install the Adapter in the machine until the software has been fully installed.

Only users running Windows 7 or newer should utilize these instructions for accessing and

installing the appropriate driver via Sealevel’s website. If you are utilizing an operating system

prior to Windows 7, please contact Sealevel by calling 864.843.4343 or emailing

[email protected] to receive access to the proper driver download and installation

instructions.

1. Begin by locating, selecting, and installing the correct software from the Sealevel software

driver database.

2. Type in or select the part number (#3541) for the adapter from the listing.

3. Select “Download Now” for SeaCOM for Windows.

4. The setup files will automatically detect the operating environment and install the proper

components. Follow the information presented on the screens that follow.

5. A screen may appear with text similar to: “The publisher cannot be determined due to the

problems below: Authenticode signature not found.” Please click the ‘Yes’ button and

proceed with the installation. This declaration simply means that the operating system is

not aware of the driver being loaded. It will not cause any harm to your system.

6. During setup, the user may specify installation directories and other preferred

configurations. This program also adds entries to the system registry that are necessary

for specifying the operating parameters for each driver. An uninstall option is also included

to remove all registry/INI file entries from the system.

7. The software is now installed, and you can proceed with the hardware installation.

Linux Installation

You MUST have “root” privileges to install the software and drivers.

The syntax is case sensitive.

SeaCOM for Linux can be downloaded here: https://www.sealevel.com/support/software-seacom-linux/.

It includes the README and the Serial-HOWTO help files (located at seacom/dox/howto). This series of

files both explains typical Linux serial implementations and informs the user about Linux syntax and

preferred practices.

User can use a program such as 7-Zip to extract the tar.gz file.

In addition, the software selectable interface settings can be accessed by referencing

seacom/utilities/3541mode.

For additional software support, including QNX, please call Sealevel Systems’ Technical Support, (864) 843-

4343. Our technical support is free and available from 8:00 AM - 5:00 PM Eastern Time, Monday through

Friday. For email support contact: support@sealevel.com.

Physical Installation

Do not install the Adapter in the machine until the software has been fully installed.

Extreme care should be taken when installing the adapter to avoid causing damage to the connectors. After

the adapter is installed, connect your I/O cable to P1. Please note these headers are keyed so that pin 1 of

the cable matches pin 1 of the connector. Refer to Card Setup for information on setting the address and

IRQ before inserting the adapter onto the stack.

1. Turn off PC power. Disconnect the power cord.

2. Remove the case cover (if applicable).

3. Gently insert the adapter noting proper key orientation of the expansion connector on a PC/104

compatible card. The adapter is keyed per the current PC/104 Specification. This will aid in

preventing the adapter from being inserted incorrectly.

4. Mounting hardware (nylon stand-offs and screws) is provided to ensure a good mechanical

connection. Retain any mounting hardware not used to allow for future expansion.

5. The cables provided are keyed and can be installed before or after the adapter is inserted in

the stack.

6. Replace the cover.

7. Connect the power cord and power up the machine.

Installation is complete

Altri manuali per C4-104.ULTRA

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SeaLevel Hardware per computer

SeaLevel

SeaLevel DuoCom Manuale utente

SeaLevel

SeaLevel ULTRA COMM+422 Manuale utente

SeaLevel

SeaLevel Route 56 Manuale utente

SeaLevel

SeaLevel ACB-ULTRA.LPCI Manuale utente

SeaLevel

SeaLevel ULTRA 485 Manuale utente

SeaLevel

SeaLevel SeaLINK+2/PC.SC Manuale utente

SeaLevel

SeaLevel SeaLINK +2.SC Manuale utente

SeaLevel

SeaLevel ACB-232.LPCI Manuale utente

SeaLevel

SeaLevel 12000 COM Express Carrier Board Manuale utente

SeaLevel

SeaLevel UltraCOMM+2.LPCIe Manuale utente

SeaLevel

SeaLevel SIO-485.LPCI Manuale utente

SeaLevel

SeaLevel SeaPORT DIO-16 Manuale utente

SeaLevel

SeaLevel SeaLINK/PC.SC Manuale utente

SeaLevel

SeaLevel REL-16 3095 Manuale utente

SeaLevel

SeaLevel LATCH-16 Manuale utente

SeaLevel

SeaLevel COMM+4.PCI Manuale utente

SeaLevel

SeaLevel ISO-16.PCI Manuale utente

SeaLevel

SeaLevel PIO-48 4030 Manuale utente

SeaLevel

SeaLevel PROM-III Manuale utente

SeaLevel

SeaLevel DIO-32B Manuale utente

SeaLevel

SeaLevel PLC-16.PCI Manuale utente

SeaLevel

SeaLevel 7202e Manuale utente

SeaLevel

SeaLevel ACB 56 Manuale utente

SeaLevel

SeaLevel ISO COMM2.cPCI Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente