SEAWIN Electricals MG0601 Manuale utente

KNX/EIB BUS

POWER ACTUATORS

Product Man

KNX Line Coupler

Manual -Ver2.1

MG0601

KNX/EIB BUS

POWER ACTUATORS

Product Man

Content

1 Overview ................................................................................................................................................................................................................ 3

1.1 Product introduction ............................................................................................................................................................................. 3

1.2 Topology .................................................................................................................................................................................................... 4

1.2.1 Line coupler .................................................................................................................................................................................. 4

1.2.2 Zone coupler ................................................................................................................................................................................. 5

1.2.3 Repeater ......................................................................................................................................................................................... 5

2 Technical performance ...................................................................................................................................................................................... 6

3 Dimension & wiring diagrams ....................................................................................................................................................................... 6

4 Instructions and operations ............................................................................................................................................................................ 6

5 Function configuration ..................................................................................................................................................................................... 7

5.1 S-Line—> M-Line control .................................................................................................................................................................. 8

5.2 M-Line--> S-Line control ..................................................................................................................................................................... 9

6 Safe use and maintenance ........................................................................................................................................................................... 10

7 Contact ................................................................................................................................................................................................................ 10

KNX/EIB BUS

POWER ACTUATORS

Product Man

1 Overview

1.1 Product introduction

The MG0601 coupler is a modular installation device that combines the functions of a KNX line coupler and a

KNX line repeater. When used as a line coupler, it connects main lines and trunk lines or regional lines. As a line

repeater, it can connect more than 64 devices on a bus. Electrical isolation is provided in this way.

The coupler sends physical addresses, group addresses and broadcast messages by path. The physical address

message is sent according to the path, and the coupler compares the target physical address with its own

physical address. Automatic filtering determines whether the corresponding physical address packets are

passed. The packets follow the path or not according to the path depending on the parameter configuration. If

the coupler has not received the project-assigned physical address, this may result in the device not being able

to communicate during commissioning. The coupler provides a filter table, all group messages present in the

filter table will be routed, otherwise they will be blocked, thereby reducing the bus load. The filter table is

automatically generated by the ETS software tool according to the commissioning system. It is useful to

configure filter group addresses in the filter table, especially during debugging and diagnostics. In the group

address, the main group address is 0....13 can configure filtering and other parameters. The main group

addresses of group packets 14....31. do not do any isolation configuration. If the coupler sends the message

along the path without receiving an acknowledgment or transmission error, repeat the message up to 3 times.

At the same time, in order to prevent false repetition of group messages, the two lines of the response are set

separately. In the standard setting this parameter can be set separately.

KNX/EIB BUS

POWER ACTUATORS

Product Man

1.2 Topology

1.2.1 Line coupler

As a line coupler, the MG0601 connects a branch line to a main line, each line requiring it to have its own power

supply. Line couplers play the role of filtering messages and reducing bus load. When used as a line coupler, its

physical address is X.Y.0 (X = 0~15, Y = 0~15), that is, there can be up to 15 main lines, and there can be 64

devices on the main line, including line couplers, which can be relayed through linker segments (up to 3-line

repeaters) for up to 3840 devices

Figure 1.1 Line coupler topology

1.2.2 Zone coupler

As a zone coupler, the MG0601 connects a main line and a zone line, each requiring its own power supply. The

regional coupler plays the role of filtering the messages and reducing the bus load. When used as a regional

coupler, its physical address is X.0.0 (X = 0~15), that is, there can be up to 15 main lines, each main line can have

up to 15 branch lines, and there can be 64 devices on the branch line including lines Couplers that can connect

line segments via repeaters (up to 3-line repeaters) for up to 57,600 devices

KNX/EIB BUS

POWER ACTUATORS

Product Man

Figure 1.2 Zone coupler topology

1.2.3 Repeaters

The MG0601 acts as a repeater, connecting the data streams of the two line segments but electrically isolated. In

a line, up to three repeaters can be connected in parallel to form a line. This is how up to four line segments form

the entire branch. Thus, spur lines can be expanded from 64 devices (1 segment) to 256 devices (4 segments).

Each line segment must be powered by its own KNX power supply.

Repeaters do not have filter tables, so it does not matter whether the message is initiated within the line, or

whether it has been sent from the main line through the repeater, regardless of which segment of the line the

message was sent on. .

If there is a transmission error in the physically addressed telegram, the telegram is not repeated. If the repeater

routes the telegram and no acknowledgment is received or there is a transmission error, the repeater repeats the

telegram up to three times. Using the parameter If an error occurs repeating the group telegram, the responses

of the two line segments will be set separately.

When used as a repeater, its physical address is X.Y.Z (X = 0~15, Y = 0~15, Z=1-255). That is, branch line, up to

256 devices.

2 Technical performance

2.1 Technical parameters

Main Input 12~30 VDC

Branch line input 12~30 VDC

KNX/EIB BUS

POWER ACTUATORS

Product Man

Bus current ≤ 10mA

Working power ≤ 3500mW

Connect Main line / branch line EIB bus connection terminal

Shell material PA66

Dimension (H x W x D) 90×38×64mm

Weight(approx.) 0.08kg

Installation method 35mm DIN-rail installation

Transportation temperature - 25°C…+70°C

Working temperature -5°C- 45°C

Storage temperature -25℃-55℃

Relative humidity max 90%

3 Dimension & wiring diagrams

Dimension Wiring diagrams

4 Instructions and operations

Main Line Branch Line

KNX/EIB BUS

POWER ACTUATORS

Product Man

Nr. Name Function

① Main Line indicator

light

Steady light indicates that the main line is connected normally;

flashing indicates that the main line has communication

② Sub LineBranch line

indicator

Blinking means there is communication on the branch line.

③ Programming button Button is used to enter/exit KNX programming mode.

④ programming light A solid light indicates programming mode.

⑤ M-L is KNX main line

terminal

To connect to the KNX main line, use standard KNX terminals.

⑥ S-L is KNX branch line

terminal

To connect to the KNX branch line, use standard KNX

terminals.

5 Function configuration

KNX/EIB BUS

POWER ACTUATORS

Product Man

MG0601 is configured through ETS4/5, which can be configured by parameters, associated with the address of

the communication object group, etc.

General Settings configuration parameters, the parameter "Device name" represents the device name, the

device name can be edited freely, and a maximum of 30 bytes are allowed.

KNX/EIB BUS

POWER ACTUATORS

Product Man

5.1 S-Line -->M- Line control

Note: The group address format is A/B/C, where A is the main group address;

The parameter "Individual framers(S->M)" indicates the filtering behavior of single frame from branch line to

main line. The options are: Router (passing), Block (blocking), Filter (filtering).

The parameter "Broadcast framers (S->M)" indicates the filtering behavior of broadcast frames from branch

lines to main line packets. The options are: Router (pass), Block (block).

The parameter "Group framers (main groups 0 to 13)" indicates the filtering behavior of group frames in the

group address packets whose main group address is 0~13. The options are: Router (pass), Block (block), Filter

(filter) .

The parameter "Group framers (main groups > 13)" indicates the filtering behavior of group framers whose

main group address is greater than 13. The options are: Router (pass) and Block (block).

The parameter "ACK of group frames(S)" indicates the ACK of branch line framing. The options are: Always

(always), Only when routing (only when Routing is available).

The parameter "ACK of individual frames(S)" represents the ACK of a single frame of the branch line. The

options are: Only when routing (only when routing), Always ACK (always ACK), Always NACK (always NACK).

The parameter "Ph. Repetition control if wrong ACK(S) means that if the branch line ACK is wrong, the device

will resend the physical address data, the options are: No (no), Normal (can).

The parameter "GRP Repetition control if wrong ACK(S) means that if the branch line ACK is wrong, the device

will resend the group address data, the options are: No (no), Normal (can)

KNX/EIB BUS

POWER ACTUATORS

Product Man

52 M-Line -->S- Line control

Note: The group address format is A/B/C, where A is the main group address;

The parameter "Individual framers (M->S)" indicates the filtering behavior of a single frame from the main line to

the branch line. The options are: Router (passing), Block (blocking), Filter (filtering).

The parameter "Broadcast framers((M->S))" indicates the filtering behavior of broadcast frames from the main

line to the branch line. The options are: Router (pass), Block (block).

The parameter "Group framers (main groups 0 to 13)" indicates the filtering behavior of group frames in the

group address packets whose main group address is 0~13. The options are: Router (pass), Block (block), Filter

(filter).

The parameter "Group framers (main groups > 13)" indicates the filtering behavior of group framers whose main

group address is greater than 13. The options are: Router (pass) and Block (block).

The parameter "ACK of group frames (M)" represents the ACK of the main line frame, and the options are: Always

(always), Only when routing (only when Routing is available).

The parameter "ACK of individual frames (M)" represents the ACK of a single frame on the main line. The options

are: Only when routing (only when routing), Always ACK (always ACK), Always NACK (always NACK).

The parameter "Phy..repetition control if wrong ACK (M) means that if the main line ACK is wrong, the device will

resend the physical address data, options: No (no), Normal (can).

Indice

Altri manuali SEAWIN Electricals Controllori

SEAWIN Electricals

SEAWIN Electricals 10A Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente