Securam ProLogic L22 Manuale utente
ProLogic L22 Operation Instructions
1
ProLogic L22 Operation Instructions
Document No: EC-0601A-L22-130919
Version No: V1.01
1.0 System Installation
1.1 System Components
1.2 Pairing the EntryPad with the Lock(s)
1.3 Lock and EntryPad Installation
1.4 Installing Battery
1.5 Test Lock Operation
2.0 Lock Operation
2.1 Opening the Lock
2.2 Opening the Lock in Time Delay
2.3 Opening the Lock Under Duress
2.4 Opening the Lock in Dual Control
2.5 Opening the Lock with a Multi-Lock System
3.0 Set Date and Time
3.1 Set Clock Time
3.2 Show Clock Time
3.3 DayLight Savings Time
4.0 Code Management
4.1 Enrolling New users
4.2 Change Code
4.3 Delete One User
4.4 Delete All Users
4.5 Disable/Enable User
5.0 System Identification
5.1 System Info
6.0 Time Delay
6.1 Set/Cancel Time Delay
6.2 Set Duress Time Delay
6.3 Setting Time Delay Override Users
7.0 Audit Trail Functionality
7.1 Show Audit Trail
7.2 Uploading Audit Trail
8.0 Single or Dual Control
8.1 Enable Dual Mode
9.0 Door Management
9.1 Max. Door Open Time
9.2 Configuring a Multi-lock system
9.3 Set Number of Locks
9.4 Authorize Locks
9.5 Enable Sequence
10.0 Duress Management
10.1 Duress Setup and Wiring Configuration
10.2 Duress Code Shift
11.0 Device Management
11.1 Set Device ID
12.0 Data Management
12.1 Encryption Key Set
13.0 Recovering the System – Reset to Default
13.1 Recovery Code Set
13.2 Recover System
13.3 Simple Mechanical Reset
14.0 System Testing
14.1 Cycle Testing
14.2 Hardware Testing
15.0 Menus
15.1 The ProLogic L22 Menus
ProLogic L22 Operation Instructions
2
1.0 System Installation
1.1 System Components
The system consists of (1) EntryPad – Part # EC-0601A-L22 plus (1) or more Lock bodies as follows:
SwingBolt – Part # EL-0601
SwingBolt with Status – Part # EL-0601-S
DeadBolt – Part # EL-0701
SpringBolt – Part #EL-0801
StrikeBolt – Part #EL-0901
Note: The ProLogic L22 can control up to 4 locks when used in conjunction with the Expansion Box –
Part # CB11-1T4. (If setting up a multi-lock system, please refer to Section 10.2 – Multi-Lock Systems)
1.2 Pairing the EntryPad and the Lock
SECURAM safe lock systems can operate in two different modes depending upon the type of EntryPad
being used with the lock body. The ProLogic L22 is a digital lock system and therefore the lock must also
be programmed in digital mode. Both modes follow the same steps to reset / set which is done by
following the steps detailed below:
Step 1: Ensure the battery is disconnected from the Entry Pad.
Step 2: Ensure the lock cable is disconnected from the lock body.
Step 3: Locate the Reset Hole on the back of the lock (under the QC sticker).
Step 4: Using a paper clip depress the reset button, inside the reset hole, 3 times to dissipate
any latent energy in the lock.
Step 5: Now depress the reset button and hold.
Step 6: While continuing to depress the reset button, connect the lock cable to the lock body.
Step 7: While continuing to depress the reset button, connect the 9V battery to the EntryPad
terminals.
Step 8: Continue to hold down the reset button for 5 seconds and then release.
Step 9: Verify that the pairing has been completed, by opening the lock with the default code
111111.
Step 10: Press any button on the EntryPad to initiate a lock communication test. The EntryPad
will display system information followed by:
ProLogic L22 Operation Instructions
3
Enter a valid code to test the lock.
The Default codes are as follows:
Super Code (ID00) is 111111
Manager Code (ID01) is 123456
Upon entry of a valid code, the lock will open. If the lock does not open and the LCD screen
displays the message “Fail to Link with Lock”, repeat the reset procedure. Be sure to hold down
the reset button through steps 5-8.
If you have difficulty resetting the lock, please call SECURAM Tech Support at (805) 988-8088 or email
1.3 Lock and EntryPad Installation
Included within your installation kit are (2) shoulder bolts and (3) lock mounting bolts.
Install the shoulder bolts on the safe door in the pre-drilled holes above and below the spindle
hole.
Now insert the lock cable (attached to the EntryPad) through the spindle hole.
On the backside of the safe door, you will see the lock mounting plate and the predrilled lock
mounting holes.
Connect the lock cable to the lock body and position the lock body appropriately on the lock
mounting plate.
Ensure that the lock cable is positioned so that it lies in the channel on the back of the lock. This
channel is provided to protect the lock cable from damage or crimping during installation.
Using the provided lock bolts, secure the lock body to the mounting plate.
Note: it is very important to ensure that there is an adequate gap between the lock bolt and the
boltwork. This gap must be 0.125”.
1.4 Installing the Battery
Connect the battery terminal clip to the 9V battery. (It is required to use standard alkaline
batteries; Duracell or Energizer batteries are preferred.)
Position the battery so that the terminals are in the downward position and push the battery
into the battery compartment.
Carefully tuck the excess lock cable into the cavity on the back of the EntryPad and install the
EntryPad on the shoulder bolts.
ProLogic L22 Operation Instructions
4
Be careful not to crimp or damage the lock cable upon EntryPad installation.
1.5 Testing the Lock Operation
The ProLogic L22 comes with two factory default codes:
• Super Code (ID00) is 111111
• Manager Code (ID01) is 123456
Enter one of the valid codes to verify that the communication between the lock and EntryPad. The lock
will open.
2.0 Lock Operation
Upon initial power up, the LCD screen starts a communications test as shown below:
Including Model Number
Software Version Number
No. of Users/ No. Users Programmed
Lock ID#/Host ID#
Model Name
No. of Audit Events
After this initial power up it will also check to ensure that the system is communicating correctly. The
display will read “Link with Lock OK”.
If the Display reads: “Fail to Link with Lock” proceed to Section 1.2 entitled “Pairing the Entrypad and
the Lock”
2.1 Opening the Lock
The safe lock system has two default codes installed as follows:
• Super Code (ID00) 1-1-1-1-1-1
• Manager Code (ID01) 1-2-3-4-5-6
Step 1: Enter a valid code – for example ID00.
The display will read “ID00 Verified”.
And the Lock will open.
ProLogic L22 Operation Instructions
5
The display will read:
The lock will relock after 6 seconds.
Note: Time to relock is hard coded and cannot be changed.
2.2 Opening Lock with Time Delay Programmed
When Time Delay has been programmed, the user must enter a valid code.
Note: Users are defined as ID03- ID30
Wait through the preprogrammed time delay period, then enter the code again to open the lock safe, as
follows:
Step1: Enter a valid code
Note: ID00, ID01 and ID02 are Administrator users and will bypass Time Delay.
Step 2: Display will read “Time Delay Start”
Step 3: Display will flash on every 15 seconds, counting up until it reaches the preprogrammed
time delay value.
Note: Administrators can override Time Delay to open lock anytime.
Step 4: When Time Delay expires, the entrypad will beep twice then display: “Time Window
XX:00”, indicating the length of time the User has to enter a valid user code to gain entry.
The Counter will count down until the Time Window has expired. A user code is used to open
the lock.
Step 5: Enter a valid Code to open the lock.
2.3 Opening the Lock Under Duress
ID00
ProLogic L22 Operation Instructions
6
The ProLogic L22 has a Duress Feature, which allows a User or Admin to open the lock and send a silent
Duress signal indicating that you are in danger. By default, the duress function is active and cannot be
disabled.
In Order to send a signal, the system must have a CB10 junction box installed and must be connected to
an alarm panel.
To Open the Lock under Duress:
Step 1: Enter a valid Code, but add or subtract 1 from the code. The Lock will open as normal and a
silent alarm will be issued.
Note: This will be logged as “Duress Unlock” in events.
For example, if your code is 123456; under Duress, enter 123455 or 123457 to send silent alarm.
Note: The ProLogic L22 has a function called “Duress Code Shift”. This function allows you to specify
the number to be added or subtracted from the code during a duress entry. See Section C - 11.0.
2.4 Opening the Lock in Dual Control
The ProLogic L22 can be programmed so that two User codes are required to open the lock. This
function is called “Enable Dual Mode”, See 8.1
To Open a Lock under Dual Control:
Step 1: Enter User code
The display will read “IDXX Verified”.
For example, ID03 will display “ID03 Verified”.
The display will then read:
“Enter 2nd User Code”
For example, using ID04 for 2nd code will read “ID04 Verified”.
The lock will open and relock in 6 seconds.
ProLogic L22 Operation Instructions
7
2.5 Opening the Lock with a Multi-Lock System
The ProLogic L22 can operate up to 4 locks.
To Open a Lock with a Multi-Lock System:
Step 1: Enter a valid code
The display will read “IDXX Verified”.
Step 2: The system will now prompt you to enter the number of the Lock to open
3.0 Set Date and Time
The ProLogic L22 is an audit lock and it tracks events based on user, activity, date, and time. In order to
set the system date and time complete the following process.
3.1 Set Clock Time
Step1: Press the Menu/OK button
Step 2: Using the and, scroll to the System Menu and press OK.
Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or
the Manager Code (ID01). The “Select Menu” message will be displayed as follows:
Step 4: Scroll to the menu selection “Set Clock Time” and Press OK
Step 5: Press OK
Step 6: Each of the elements of the date and time will flash when it is available to be set. Use the
and to scroll to the correct value and Press OK to move to the next element.
3.2 Show Clock Time
Step1: Press the Menu/OK button
Step 2: Using the and, scroll to the System Menu and press OK.
ProLogic L22 Operation Instructions
8
Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or
the Manager Code (ID01). The “Select Menu” message will be displayed as follows:
Step 4: Scroll to the menu selection “Show Clock Time” and Press OK
Step 5: The LCD will display the current system date and time, as follows:
3.3 DayLight Savings Time
The ProLogic L22 can be set to manage Daylight Savings Time and automatically updating preset date
and time. Using this menu selection, you can turn on Daylight Savings Time management or turn it off.
**Note: The example below shows that Daylight Savings Time will start in March (3rd month), 2nd full
week at 2:00 am on the first day of the week (Sunday). And Day Light Savings Time will end in
November (11th month), 1st full week at 2:00 am on the first day of the week (Sunday).
Step1: Press the Menu/OK button
Step 2: Using the and , scroll to the System Menu and press Menu/OK
Step 3: The display will prompt you to enter a valid code. Enter either the Super Code (ID00) or
the Manager Code (ID01). The “Select Menu” message will be displayed as follows:
Step 4: Scroll to the menu selection “Daylight Savings TM” and Press OK
Step 5: Press the button to turn Daylight Savings Time Management on. (To turn it off, press
the button)
ProLogic L22 Operation Instructions
9
Step 6: (Starting Month) The system will now request the month in which Daylight Savings Time
is to begin. The default is North American DST Month 3 – March. To change press the and
to set the Month; and press OK
Step 7: (Starting Week) The system will now request the week of the month in which Daylight
Savings Time is to begin. The default is North American DST Week 2 – note – the system
calculates this as the 2nd full week in this month. To change Press the and to set the Week;
and press OK
Step 8: (Starting Time) The system will now request the Time on the first day of the week
(Sunday) at which Daylight Savings Time is to begin. The default is North American DST Time 2 –
2:00am. To change Press the and to set the Time; and press OK
Step 9: (Ending Month) The system will now request the month in which Daylight Savings Time
is to end. The default is North American DST Month 11 – November. To change press the and
to set the Month; and press OK
Step 10: (Ending Week) The system will now request the Week in which Daylight Savings Time
is to end. The default is North American DST Week 1 – note – the system calculates this as the
1st full week in this month. To change Press the and to set the Week; and press OK
Step 11: (Ending Time) The system will now request the Time on the first day of the week
(Sunday) at which Daylight Savings Time is to end. The default is North American DST Time 2 –
2:00am. To change Press the and to set the Week; and press OK
ProLogic L22 Operation Instructions
10
Therefore to set to the North American DST, just select “Y” on the first display screen and then accept
the defaults for all other settings by pressing OK.
4.0 Code Management
The ProLogic L22 comes with two default codes:
• Super Code (ID00) is 111111
• Manager Code (ID01) is 123456
It is strongly recommended that both these default codes are changed before the lock system is put into
service.
4.1 Enrolling New Users
Step1: Press the Menu/OK button.
Step 2: Using the and , scroll to the System Menu and Press Menu/OK
Step 3: The display will prompt you to enter a valid Administrator code
Enter either the Super Code (ID00) or the Manager Code (ID01). The “Select Menu”
message will be displayed as follows:
Step 4: Scroll to the menu selection “Enroll New User” and Press OK
Step 5: The next available ID position is displayed. To select this ID, Press OK; or to select a
different ID position, Press to desired ID and press OK
Step 6: Now enter a 6 digit code
Step 7: Repeat new code
Step 8: System will verify that code has been saved.
Altri manuali per ProLogic L22
1
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Securam Serratura
Securam
Securam SafeLogic Xtreme Manuale del proprietario
Securam
Securam ProLogic B01 Manuale utente
Securam
Securam SafeLogic Basic Series Manuale utente
Securam
Securam ProLogic L02-C Manuale utente
Securam
Securam SafeLogic TopLit Series Manuale utente
Securam
Securam EM-1701A-R Manuale utente
Securam
Securam SCANLOGIC FPC-1808-II-MB Manuale utente
Securam
Securam ProLogic L22 Manuale utente
Securam
Securam ProLogic L66 Manuale utente
Securam
Securam SafeLogic Basic Manuale utente
Securam
Securam ScanLogic B22 Manuale utente
Securam
Securam D Series Manuale utente
Securam
Securam SafeLogic Basic Manuale utente
Securam
Securam SafeLogic Basic Manuale utente
Securam
Securam ScanLogic D66 Manuale utente
Securam
Securam SH-TB01 Manuale utente
Securam
Securam SafeLogic Xtreme Manuale utente
Securam
Securam ECSL-601 Manuale utente
Securam
Securam FPC-0601A-D22 Manuale utente
Securam
Securam ScanLogic Optical Manuale di installazione
