Securam SafeLogic Xtreme Manuale utente

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 1

SafeLogic Xtreme - Electromechanical Redundant Safe Lock System - Instructions

Please visit the website below by scanning the QR code with your smartphone or by typing in the

address below for video instructions on SafeLogic Xtreme Install Instructions.

http://goo.gl/3pZ16W

Important:

1. Do not remove the back cover of the lock case.

2. Modifications of the lock are not recommended and will void product warranty.

3. Use a brand new 9V ALKLINE battery only. Recommend batteries: EnergizerTM or DuracellTM

brand.

4. Note that the 4-wire cable connectors have lock-tabs attached to ensure that the cable is

securely connected and locked into place. To prevent damage to this connector, it is required

to pinch the lock-tab when disconnecting the 4-wire cable connector from the socket.

5. Package consists of:

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 2

1. EC-1501A-X EntryPad.

2. XL-1501 Electromechanical Lock Body.

3. Spindle –drilled and tapped at one end.

4. Combination Change Key.

5. Lock Mounting Bolt: 3 PCS. Used to install the electromechanical lock body to the mounting

plate.

6. Spindle Bolt to secure the spindle to the SpinDial: 1 PC.

7. DialRing Mounting Bolt: 4 PCS. Used to install the EntryPad to the front of the safe door. 8.

Clear Plastic Spindle Tube

IMPORTANT: Do NOT use power tools to install the SafeLogic Xtreme.

1.0 Preparing to Install the DialRing and EntryPad

Separate the DialRing from the EntryPad:

Step 1: Pull up on the SpinDial release to disengage the electronics.

Step 2: Rotate the EntryPad 180 degrees to gain access to the EntryPad bolt which is located at

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 3

the 6 o’clock position on the EntryPad.

Step 3: Loosen the screw to disconnect the EntryPad from the DialRing.

Step 4: Remove the EntryPad from the DialRing by pulling the EntryPad away from the DialRing.

Note: The Entrypad and dial ring are held together by magnets to prevent the Entrypad from

falling off when unscrewing.

2.0 Installing the DialRing

Step 1: Locate the DialRing mounting holes and spindle hole (minimum 10mm Dia) on the safe

door

Step 2: Make sure the spindle hole is de-burred and has no sharp edges that could damage the

cable.

Step 3: Make sure the 4-wire cable is not crimped or folded against itself under the DialRing as

you prepare to mount it to the safe.

Step 4: Route the cable through the spindle hole.

Step 5: Position the DialRing to be mounted.

Step 6: Using the DialRing Mounting bolts (Part# M4 Bolt), install the DialRing on to the safe door.

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 4

The mounting hole at the bottom of the DialRing is covered by the rotating dial. First pull

up on the Spin Dial Release then turn the dial to expose the mounting hole and install

the DialRing Mounting bolt (Part# M4 Bolt).

Note: In most safe installations, there are only two DialRing mounting holes, either aligned

vertically or horizontally. Two bolts are adequate to secure the DialRing in place.

Step 7: Tighten the DialRing Mounting bolts (Part# M4 Bolt) to hold the DialRing in place. It is not

necessary to securely tighten the Dial Ring Mounting bolts (Part# M4 Bolt), as the

installation of the DialRing shall be adjusted during the next steps.

Step 8: Cut the supplied clear plastic spindle tube (Part# TB-9/80-P) to a length equal to Door

Thickness, where the Door Thickness or “DT” is the measurement from the Safe door

outer surface (the surface upon which the DialRing is to be mounted) to the lock body

mounting plate (the surface upon which the lock body is to be mounted).

3.0 Installing the Lock Body

Step 1: Gently pull on the 4-wire cable to ensure there is no excess cable in the spindle hole and

place the cable as shown.

Step 2: Insert the clear plastic spindle tube (Part# TB-9/80-P) into the spindle hole until it comes

into contact with the DialRing. It will be protruding into the safe approximately 3/8”

beyond the surface of the lock mounting plate.

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 5

Step 3: Use the three lock mounting bolts provided to fasten the lock body to the mounting plate.

Run the cable through the channel provided on the lock body as pictured below. Ensure

the cable is not crimped or folded against itself under the lock as you prepare to fasten

the lock body to the mounting plate.

Note: Do not tighten fully yet, this will be done during step 15.

4.0 Installing the Spindle

Step 1: IMPORTANT: Turn the SpinDial until the number “00” aligns with the twelve o’clock

position of the ring. Close the SpinDial release, so the dial is locked down at “00” and

cannot be rotated.

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 6

Step 2: Take note of the 3 ports (holes) surrounding the spindle insertion point on the lock cover

as pictured below. These “Locator Ports” will be used to position the cam inside the lock

correctly for SpinDial access.

Step 3: Now insert the spindle (Part# MSP-15A-6IN) into the spindle insertion point about ¼” so

that the spindle engages with the cam inside the lock body.

Step 4: Turn the spindle until the three small Phillips head screws are visible in the Locator Ports

as shown as demonstrated in picture below.

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 7

Step 5: Now that the cam is oriented correctly, remove the spindle (Part# MSP-15A-6IN).

Step 6: The spindle (Part# MSP-15A-6IN) has one end that is drill and tapped to receive the

Spindle Bolt (Part# M4*16). This drilled and tapped hole will be used to connect the

spindle to the DialRing. Locate the drilled and tapped hole end of the spindle and insert

this end of the spindle into the spindle insertion point as seen below. Ensure that the

spindle is inserted through the clear plastic spindle tube.

Step 7: Continue to push the spindle into place until it reaches the DialRing hub.

Step 8: At the DialRing, insert the Spindle Screw (Part# M4*16) into the DialRing hub and

tighten.

Caution:

a. Ensure that the cable is held taught while inserting the spindle. Make sure the cable will not

be crimped by the spindle.

b. Make sure the spindle can smoothly slide into the hub of the DialRing. If the spindle does not

engage into the hub, reposition the DialRing to allow the spindle to properly align with the

hub.

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 8

c. IMPORTANT: Double check to make sure that the Dial Ring is locked down at “00” and that

the small Phillips head screws are aligned correctly with the Locator Ports.

Step 9: Mark the spindle length flush to the lock cover.

The length of the spindle can be

precut to a length equal to Door

Thickness (DT) + 1.75”

Step 10: Remove the spindle bolt (Part# M4*16) and spindle (Part# MSP-15A-6IN) from lock case

prior to cutting. Carefully cut the spindle so that it will be flush to the lock cover.

Step 11: Remove all burrs from the spindle using a file.

Step 12: Now insert the Spindle (drilled and tapped end first) into the spindle insertion point and

through the clear plastic tube. Ensure that the cable is held taught while inserting the

spindle so that it does not become damaged.

Step 13: Continue to push the spindle into place until it reaches the DialRing hub.

Step 14: At the DialRing, insert the M4*16 spindle screw into the DialRing hub and tighten. Now

tighten the Lock Mounting Bolts (QTY: 3)

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 9

Step 15: IMPORTANT: Now from the Lock body side, tighten the small Phillips head screws to

lock the spindle into place at the cam.

5.0 Check the Installation of the DialRing

Step 1: Pull up on the SpinDial release, so the dial can now be rotated.

Step 2: Rotate the dial, and adjust the installation position of the DialRing to find the best position

at which the dial turns freely without scraping or binding.

Step 3: Now securely tighten the DialRing mounting bolts (Part# M4 Bolt).

Step 4: Once tightened down, rotate the dial again, to confirm that there is no scraping or binding

between the Dial and the DialRing. If there is binding or scraping, loosen the mounting

bolts again and adjust the position of the DialRing accordingly.

6.0 Install Electronic EntryPad

SafeLogic Xtreme Installation and Operation Instructions Doc. No. XU-EC1501A-X151123

SecuRam Systems Inc. Page 10

Step 1: Install the 9V ALKALINE battery in the back of the EntryPad. Embossed in the bottom of

battery compartment you will see the battery orientation markings: “+” and “-“. Install

the battery with the correct orientation as indicated by the “+” and “-“.

Note: If at any time, after inputting a code you hear 8 rapid continuous beeps, it means that the

battery needs replacing. Please be sure to replace with either Energizer or Duracell Alkaline 9V

batteries.

Step 2: IMPORTANT: Pull up on the SpinDial release to disengage the electronics. Rotate

the Dial 180 degrees to “50”.

Step 3: Now install the EntryPad onto the DialRing. The EntryPad should be properly seated on

to the DialRing, with the keypad face upside down.

Altri manuali per SafeLogic Xtreme

Indice

Altri manuali Securam Serratura

Securam

Securam D Series Manuale utente

Securam

Securam FPC-0601A-D22 Manuale utente

Securam

Securam V8 Manuale tecnico

Securam

Securam ProLogic L22 Manuale utente

Securam

Securam SH-TB01 Manuale utente

Securam

Securam ProLogic L66 Manuale utente

Securam

Securam ScanLogic B22 Manuale utente

Securam

Securam ScanLogic D66 Manuale utente

Securam

Securam ECSL-601 Manuale utente

Securam

Securam SafeLogic TopLit Series Manuale utente

Securam

Securam SCANLOGIC FPC-1808-II-MB Manuale utente

Securam

Securam ProLogic L22 Manuale utente

Securam

Securam SH-WB01 Manuale utente

Securam

Securam ProLogic B22 Manuale utente

Securam

Securam SafeLogic Basic Series Manuale utente

Securam

Securam EM-1701A-R Manuale utente

Securam

Securam SafeLogic Basic Manuale utente

Securam

Securam SafeLogic Basic Manuale utente

Securam

Securam ScanLogic Optical Manuale di installazione

Securam

Securam SafeLogic Xtreme Manuale del proprietario

Securam

Securam ProLogic L01 Manuale utente

Securam

Securam SafeLogic Basic Manuale utente

Securam

Securam SafeLogic C10 D-Drive Manuale utente

Securam

Securam ProLogic L02-C Manuale utente

Manuali Serratura popolari di altre marche

Magic

Magic 105 Manuale utente

Gantner

Gantner GAT NET.Lock 7020 System Guida rapida

Wittkopp

Wittkopp Insys 7202 Manuale utente

Dorma

Dorma Studio Classic Manuale utente

Sudhaus

Sudhaus 3003 Manuale utente

Safety 1st

Safety 1st 48517 Manuale utente

Pado

Pado FDS-10 Manuale utente

Esco

Esco systeQ Series Manuale utente

COMPX

COMPX National D8951 Manuale utente

secureo

secureo Key Box Manuale utente

Stock Loks

Stock Loks C8713 Manuale utente

COMPX

COMPX 1T-058 Manuale del proprietario

Auslock

Auslock T11 Manuale utente

ELCOM

ELCOM 7205 Manuale utente

Stealth SAFES

Stealth SAFES ShadowVault Manuale utente

Knox

Knox KeySecure 5 Manuale utente

Kwikset

Kwikset 48334/01 Manuale utente

Metra Electronics

Metra Electronics Door Access Terminal Combo Manuale utente