SenseAir tSense Manuale utente
0
CO2, Temperature, and Relative Humidity
Transmitter
tSense Touch Screen
User’s Manual
1
General
tSense for wall mounting measures indoor air carbon dioxide concentration,
temperature and relative humidity in rooms. tSense is available with or without color
touch display (LCD).
The unit can be connected to a Direct Digital Control (DDC) system.
Linear outputs are pre-programmed as CO2-, temperature- and relative humidity
transmitter. Measuring ranges can be modified from PC (Windows) software UIP
(version 5 or higher) and USB communication cable, alternative via Modbus or
BACnet.
Table of Contents
General 1
Display menu…………………………….…………………………………….. 2
Measured values………………………………………………………………. 2
CO2 /Temperature/Humidity………………...…………………………….. 2
Limit settings…………………………………….…………………………….. 2
CO2 /Temperature/Humidity………………...…………………………….. 2
Display appearance…………………………….…………………………… 3
CO2 /Temperature/Humidity Char………….…………………………….. 3
Brightness…………………………………….…………………………….. 3
Background…………………………………...…………………………….. 3
Sleep scheme………………………………..……………………………... 4
Toggle Time…..…………………………………………………………….. 4
Temperature and PIN selection…………….…………………………….. 5
Output configurations……………………….…………………………….. 6
Download software…………………………...…………………………….. 7
Self-diagnostics………………………………..…………………………….. 9
Error codes and action plans…………….…………………………….. 10
Opening of housing…………………………..…………………………….. 11
Maintenance……………………………………..…………………………….. 11
Support……………………………………..……………………………………. 12
Warranty……………………………………..………………………………….. 12
Returns …………………………………..……………………………………… 12
Contact ……………………………………..……………………………………. 13
2
MEASURED VALUES
CO2/Temperature/Humidity
=
LIMIT SETTINGS
CO2/(Temperature)/(Humidity)
CO2Orange/Red limit (Temp./Humidity Orange/Red limit: same method as CO2
Orange/Red limit)
100,200,300ppm =
3
DISPLAY APPEARANCE
CO2 /Temperature/Humidity Chart 24h/Week
=
Brightness/Background/Sleep Scheme/Toggle
Brightness
10, 20,…100% =
Background
=
4
Sleep scheme
3,4,5…10 s
= = =
Toggle time
=
5
Temperature unit selection
=
Change PIN code
=
6
Output Configurations
Terminal
Default
Output Default Output Range Outputs of this
sensor
Output Ranges of this
sensor
OUT(1)
0 - 10 VDC
0 - 2000ppm CO2
See label
See label
OUT(2)
0 - 10 VDC
0 - 50oC
See label
See label
OUT(3)
0 - 10 VDC
0 - 100%RH
See label
See label
Table 1. Default output configurations of tSENSE
Figure 1: Terminal
The sensor is supplied with 0 - 10VDC linear outputs for Out(1), Out(2)and Out(3)
(see Table 1). Alternative output ranges can be configured with PC software UIP
(version 5 or later, see below).
Figure 2: Connection to PC.
7
Download software UIP5
Download software UIP (version 5 or higher) at
www.senseair.se/products/software/uip-5/
Check for updates
Run until…
For more information see Help in the UIP5 program.
Connection configurations
8
Changing Modbus/BACnet Network Address
Modbus address, BACnet MACaddress
CO
2
ABC
9
Outputs
All functions listed on pages 7-9 can be accessed directly
from the touch screen.
Automatically system-test
A full system test is executed automatically at every power-up. Sensor probes are
checked constantly during operation against failure by checking valid dynamic
measurement ranges. All EEPROM updates, initiated by the sensor itself and by
external connections are checked by subsequent memory read back and data
comparisons.
System checks returns error bytes to RAM. Error codes are available by connecting
the sensors to a PC with a special USB cable (art.no. 00-0-0070) connected (see fig.
2). Error codes are shown in software UIP (version 5 or higher).
Indice
Altri manuali SenseAir Trasmettitore
SenseAir
SenseAir eSENSE Ind Manuale utente
SenseAir
SenseAir tSENSE (Disp) T RH RL Manuale utente
SenseAir
SenseAir aSENSE Manuale utente
SenseAir
SenseAir eSENSE Manuale utente
SenseAir
SenseAir aSENSE Manuale utente
SenseAir
SenseAir aSENSE GH (Disp) RL Manuale utente
SenseAir
SenseAir tSENSE VAV Manuale utente
SenseAir
SenseAir aSENSE Manuale utente
SenseAir
SenseAir aSENSE Manuale utente
SenseAir
SenseAir aSENSE Manuale utente
