SenseGlove DK1 Manuale utente
Getting started with the
SenseGlove DK1
November 2019 (v.1.3h)
Copyright SenseGlove © 2020 all rights reserved.
Table of Contents
What’s in the box
Mounting an HTC Vive tracker
Setup a SenseGloves pair
How to wear the SenseGlove
Setup a single SenseGlove
Getting started with your first project
How to contact us
Specifications
4
10
6
12
8
13
13
14
2
The SensGlove Developers Kit 1 (DK1) is a
prototype and not certified. SenseGlove or its
related companies cannot be held liable for
damages caused by the SenseGlove DK1. In using
the SenseGlove you accept all risks and liabilities.
The user is advised to follow the ‘getting started
guide’.
It is particularly important to use the USB
cables provided since they withstand the power
consumption of the SenseGlove.
We mention the HTC Vive tracker in this manual,
therefore, it should be noted that, HTC and Vive
are trademarks or registered trademarks of HTC
Corporation and its affiliates in the U.S. and other
countries.
Disclaimer
3
The schematics below gives the items you find
inside of the box. Underneath the LinkBox you can
find the required accessories.
SenseGloves
(left and right)
2x 3m (10ft)
USB cable
1x 2m (6.5ft)
USB cable
What’s in the box
1x
SenseGlove
LinkBox
1x Power
cable
4
2x HTC Vive
tracker
mount
2x Screw
(1/4-20UNC)
for mounting
the HTC Vive
tracker on the
adapter
2x Screw (M3
6mm, T10) for
mounting the
adapter on the
SenseGlove
5
The schematic below gives a correct SenseGlove
setup. What you need are:
• SenseGlove pair
• LinkBox
• Two long (3m / 10ft) USB cables
• One short (2m / 6.5ft) USB cable
• Power cable
Setup a SenseGloves pair
6
Step 1: Connect the LinkBox to the power. Install
the power cable in the LinkBox. Put the other side
of the power cable in a power socket (100-240V,
50-60Hz). If connected correctly, the Blue LED on
the LinkBox lights up.
Step 2: Connect the LinkBox with a computer.
Install the short USB cables with the micro USB
into the LinkBox. The other side of the short USB
cable should be connected to USB ports on a
computer.
Step 3: Connect the SenseGloves to the LinkBox,
with the two long USB cables. The micro USB
plug connects to the SenseGlove and the other
side of the cable is connected to the LinkBox.
Warning: Only use the provided
USB cables to connect the
SenseGlove. The provided USB
cables withstands the power
consumption of the SenseGlove,
regular USB cables might not.
7
The schematic on the next page shows how to
setup the SenseGlove. What you need are:
• SenseGlove
• LinkBox
• One long USB cable
• One short USB cable
• Power cable
If you use only one SenseGlove in your project, you
can follow the steps as indicated on the previous
page, using only one SenseGlove.
Setup a single SenseGlove
8
9
An HTC Vive tracker can be mounted on the
SenseGlove using the supplied mount. The
schematic on the next page shows the way to
install the HTC Vive tracker on the SenseGlove.
What you need are:
• SenseGlove
• Tracker mount
• Screw 1/4-20 UNC threaded mount
• Screw M3, 6 mm (T10)
• Screw driver Torx 10 (not provided)
Step 1: Attach the HTC Vive tracker to the mount
using the 1/4 inch UNC screw.
Step 2: Place the mount with attached tracker
on the SenseGlove corresponding to the middle
finger, and attach it with the M3 screw.
Mounting an HTC Vive tracker to the
SenseGlove
10
Indice
Altri manuali SenseGlove Robotica
