SGM X-5 Manuale utente
X·5 / XC·5
LED STROBE
2
X·5 / XC·5 LED STROBE
USER MANUAL REV. 2
X·5 / XC·5 LED Strobe dimensions
All dimensions in mm. Drawing not to scale.
3
X·5 / XC·5 LED STROBE
USER MANUAL REV. 2
© 2010-2012 SGMTM. Information subject to change without notice. SGM and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential
or economic loss or any other loss occasioned by the use of, inability to use or reliance
on the information contained in this manual. The SGM logo, the SGM name and all other
trademarks in this document pertaining to services or products by SGM or its afliates and
subsidiaries are trademarks owned or licensed by SGM or its afliates or subsidiaries.
X·5 / XC·5 LED Strobe uk
4
Contents
Safety Information....................................................................................................5
Preparation for Use...................................................................................................7
Controller Operation.................................................................................................9
Setup..............................................................................................................10
DMX Control Summary...........................................................................................12
Service......................................................................................................14
DMX Protocols........................................................................................................15
Specifications.........................................................................................20
Users notes.......................................................................................................................22
5
Safety Information
Strobe lights are known to trigger epileptic seizures in persons who are photosensitive.
• Do not open: there are no user-serviceable parts inside.
• Always ground (earth ) the xture electrically.
• Use only a source of AC power that compiles with local building and electrical codes and has both overload and
earth leakage protection.
• Do not expose the xture to rain or moisture.
WARNING!
This product is for professional use only! It is not for household use.
To guard against electric shock.
6
• Do not stare directly into the light.
• Never attempt to bypass the fuse. Always replace defective fuses with ones of the specied type and rating.
• Verify that the power feed cable is rated for the current draw of all connected xtures.
• Keep all combustible materials (for example fabric, wood, paper) at least 0.5 meters (20 inches) away from the
xture. Keep ammable materials well away from the xture.
• Provide a minimum clearance of 0.1 meters (4 inches) around air vents.
• Do not modify the xture or install other than genuine SGM parts.
• Do not operate the xture if the ambient air temperature (Ta) exceeds 40˚ C (104˚ F).
• Do not operate the xture near stairways.
• Provide advance notice that strobe lighting is in use.
• Avoid extended periods of continuous ashing, particularly at frequencies of 10 to 20 ashes per second.
To guard against UV radiation, burn, and re.
To guard against epileptic seizure..
7
Preparation for Use
Unpacking
• Strobe Light Fixture
• User manual
• Mains power cable
• Foot − black aluminium plate
The packing material protects the xture during shipment, please retain for future transportation of the xture.
AC Power Connection
The auto-ranging power supply automatically adjusts to AC power from 200-240 volts nominal at 50/60 Hz.
The current required by the X-5/XC-5 is 4 amps. To avoid overload, allow one 4 amp branch circuit per xture to
operate the X-5/XC-5 model at full power.
Use 2.5 mm2 (13 AWG) or larger power feed cables and keep runs as short as possible.
8
To rig the xture
Before installing, verify that;
• the attachment hardware is in good condition and designed to carry at least 10 times the xture’s weight,
• the structure can support at least 10 times the weight of all installed xtures, clamps, cables, auxiliary equipment, etc.;
• the clearance around the air vents is at least 0.1 meters (4 in.).
• Loosen the mounting bracket and adjust the xture to the desired angle.
• Connect and arrange the power and data cables.
Always use a secure means of secondary xing such as a safety wire
9
Controller Operation
This section describes how to operate the X-5/XC-5 with a DMX controller.
Data Connection
The X-5/XC-5 provided 5-pin XLR sockets for data connection. The pin-out on all sockets is pin 1 to shield, pin
2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5. The sockets are wired in parallel: both
inputs connect to both outputs. For reliable data transmission use one input and one output!
To connect the data link
1. Connect the DMX data input from the controller to the xture 5-pin input (male) socket.
2. Connect up to 31 additional xtures output-to-input.
3. Insert a termination plug in the output of the last xture on the link.
Data Connection Tips
• Use shielded twisted-pair cable designed for DMX devices: standard microphone cable cannot transmit control
data reliably over long distance. 24 AWG cable is suitable for distances up to 300 meters (1000 ft.). Use heavier
gauge cable and/or a DMX splitter/amp for longer distances.
• Do not overload the link. Up to 32 devices may be connected on a serial link.
• Terminate the link by installing a termination plug in the output socket of the last xture. The termination plug,
which is a male XLR plug with a 120 ohm, 0.25 watt resistor soldered between pins 2 and 3, absorb the control
signal so it does not reect and cause interference.
10
Setup
The xture uses an interactive display for setting up DMX address and operation mode. Use the ve buttons next to the
display to navigate the setup structure (Fig. 1).
When the product is switched on, the xture will be at its default setting showing the ROOT menu (Fig. 2).
The root menu show a summary of the setup information, selected DMX address, operation mode, data indicator and protocol.
Fig. 1 Fig. 2
Operation
mode
DMX
Address
Data
protocol
Data
indicator
Altri manuali per X-5
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali SGM Attrezzatura per DJ
SGM
SGM P-10 Manuale utente
SGM
SGM LB-100 Manuale utente
SGM
SGM P-1 Manuale utente
SGM
SGM G-4 RGBAM WASH Manuale utente
SGM
SGM P-10 Manuale utente
SGM
SGM P-5 Wash Light Manuale utente
SGM
SGM I-5 WASH LIGHT Manuale utente
SGM
SGM P-6 Manuale utente
SGM
SGM MOVING HEADS SERIES Manuale utente
SGM
SGM Idea Par LED Zoom RGB Manuale utente
SGM
SGM P-5 Series Manuale utente
SGM
SGM PALCO 3+ Manuale utente
SGM
SGM VPL1220-20 Manuale utente
SGM
SGM Giotto profile 400 Manuale utente
SGM
SGM R-2 RGBW Manuale utente
SGM
SGM P Series Manuale utente
SGM
SGM ILD Manuale utente
SGM
SGM Idea spot 575 Manuale utente
SGM
SGM G-1 BEAM Manuale utente
SGM
SGM G-Spot Turbo Manuale utente
