Shandong BK-T680 Manuale utente

USER’S MANUAL

Embedded Printer

BK-T680

Shandong New Beiyang Information Technology Co., Ltd.

BK-T680 User’s Manual

- 1 -

Declaration

Information in this document is subject to change without notice. SHANDONG NEW BEIYANG

INFORMATION TECHNOLOGY CO., LTD. (hereinafter referred to as “SNBC”) reserves the right to

improve products as new technology, components, software, and hardware become available. If users

need further data about these products, please feel free to contact SNBC or your local dealer.

No part of this document may be reproduced or transmitted in any form or by any means for any purpose

without the express written permission of SNBC.

Printed in China

Version 1.1

Trademark

Registered trademark of SNBC:

Warning and caution

Warning: Items shall be strictly followed to avoid injury or damage to body and equipment.

Caution: Items with important information and prompts for operating the printer.

Caution: Thermal elements. No touching.

Warning: Do not touch equipment to avoid damaging it for static electricity.

SNBC has been approved by the following certifications:

ISO9001 Quality Control System Certification

ISO14001 Environmental Management System Certification

OHSAS18001 Occupational Health and Safety Management System Certification

IECQ QC080000 Hazardous Substance Process Management System Certification

Address: No.169 huoju road, high-tech zone, Weihai, China

Hot line: 400-618-1368、800-860-1368

Fax: +86-631-5656098

PC: 264209

Website: www.newbeiyang.com.cn

BK-T680 User’s Manual

- 2 -

Safety instructions

Before installing and using the printer, please read the following items carefully:

1) Install the printer on a flat and stable surface;

2) Reserve adequate space around the printer so that convenient operation and maintenance can be

performed;

3) Keep the printer far away from water source, and do not expose the printer to direct sunlight, strong

light and heat;

4) Do not use or store the printer in a place exposed to high temperature, high humidity or serious

pollution;

5) Do not place the printer in a place exposed to vibration or impact;

6) No condensation is allowed to the printer. In case of such condensation, do not turn on the power

until it has completely gone away;

7) Connect the printer power to an appropriate grounding outlet. Avoid sharing one electrical outlet with

large power motors or other devices that may cause the fluctuation of voltage;

8) Disconnect the power when the printer is deemed to idle for a long time;

9) Don’t spill water or other electric materials into the printer (e.g. metal). In case this happens, turn off

the power immediately;

10) Do not allow the printer to start printing when there is no recording paper installed; otherwise the

print head and platen roller will be damaged;

11) To ensure quality print and normal lifetime, use recommended paper or its equivalent;

12) Shut down the printer when connecting or disconnecting interfaces to avoid damages to control

board;

13) Set the print darkness to a lower grade as long as the print quality is acceptable. This will help to

keep the print head durable;

14) Do not disassemble the printer without permission of a technician, even for repairing purpose;

15) Keep this manual safe and at hand for reference purpose.

BK-T680 User’s Manual

- 3 -

Content

1 Overview.................................................................................................................................................................. 1

1.1 Introduction...................................................................................................................................................... 1

1.2 Main features................................................................................................................................................... 1

2 Main technical index.............................................................................................................................................. 3

2.1 Technical specifications.................................................................................................................................3

2.2 Paper specifications....................................................................................................................................... 4

3 Structure and functions......................................................................................................................................... 6

3.1 Appearance......................................................................................................................................................6

3.2 Overall size...................................................................................................................................................... 6

3.3 Print module and controlling parts............................................................................................................... 8

3.4 Presenter.......................................................................................................................................................... 9

4 Installation and suggestion................................................................................................................................. 10

4.1 Unpacking...................................................................................................................................................... 10

4.2 Adjusting paper guide.................................................................................................................................. 10

4.3 Adjusting mark sensor position.................................................................................................................. 11

4.4 Grounding...................................................................................................................................................... 12

4.5 Connecting power adapter..........................................................................................................................12

4.6 Connecting interface cable......................................................................................................................... 13

4.7 Installing paper roll and loading paper...................................................................................................... 13

4.8 Installing printer.............................................................................................................................................15

4.9 Installing printer driver................................................................................................................................. 17

5 Routine maintenance...........................................................................................................................................22

5.1 Cleaning mark sensor.................................................................................................................................. 22

5.2 Cleaning print head and platen roller........................................................................................................ 23

5.3 Cleaning paper out sensor..........................................................................................................................24

5.4 Cleaning retraction sensor.......................................................................................................................... 25

5.5 Clearing jammed paper in the cutter......................................................................................................... 25

5.6 Clearing jammed paper in the presenter.................................................................................................. 26

6 Interface signal..................................................................................................................................................... 27

BK-T680 User’s Manual

- 4 -

6.1 RS-232 interface........................................................................................................................................... 27

6.2 USB interface................................................................................................................................................ 28

6.3 Power interface............................................................................................................................................. 29

7 Troubleshooting and maintenance....................................................................................................................30

7.1 Error type and settlement............................................................................................................................ 30

7.2 Solution for common errors.........................................................................................................................31

Appendix.................................................................................................................................................................... 33

Appendix 1 Self-test page...................................................................................................................................33

Appendix 2 Software Tools................................................................................................................................ 37

Appendix 3 Optional parts.................................................................................................................................. 38

BK-T680 User’s Manual

1 Overview

1.1 Introduction

BK-T680 printer is a high performance embedded 2-sided thermal printer equipped with cutter and

presenter, and it can accept up to 300mm paper roll. The maximum print width is 80mm. It can be widely

used in various Kiosk applications like information consulting terminal, data communication terminal, and

test instrument terminal, etc.

The printer is configured with the following modules:

2-sided thermal (2ST) print unit

Presenter

Anti-jam module

Control board

Cutter

LED paper outlet mouth module

BK-T680 can be connected with other devices via serial interface and USB interface. Drivers are

available for WINDOWS2000/XP/2003/Vista/2008/Win7, Windows XP Embedded operating systems

and the software development kit based on DLL.

1.2 Main features

Printing

High-speed printing

1ST printing:

Print speed of 203DPI model is 275mm/s;

Print speed of 305DPI model is 180mm/s.

2ST printing:

Print speed of 203DPI model is 150mm/s;

Print speed of 305DPI model is 100mm/s.

Low-noise thermal printing

PRESENTER

Paper accommodation

Paper retraction

Paper holding

Paper ejection

Paper throw-out

Note: Presenter is a mechanism used to accommodate paper at the front end of printer.

High reliability

The cutter lifetime can be up to 1 million cuts (paper thickness: 65μm);

Print head lifetime is no less than 100km (duty ratio 12.5%);

MCBF: 37,000,000 lines (paper feeding)

BK-T680 User’s Manual

Applications

Command set is compatible with ESC/POS standard;

Characters processing: enlarge 1 to 6 times horizontally or vertically, rotation print (0°, 90°,

180°, 270°), black/white reverse, underline, upside-down print, bold;

Barcode printing: print barcode by commands in horizontal and vertical directions;

Character size (Font A or Font B) can be selected by commands.

Printer maintenance

Replace paper roll easily;

Clean the print head conveniently

Characteristics and parameters can be set by software;

Cut paper automatically;

Semi-auto paper loading;

Mark identification and calibration;

Printer firmware on-line updating.

BK-T680 User’s Manual

2 Main technical index

2.1 Technical specifications

Item

Parameter

Printing

Print method

Thermal

Resolution

203/305DPI

Paper width

48~82.5±0.5 mm

Print width

Max.80mm (3.2 ")

Max.640 dots

Print height

Max: 800mm

Min: 70 mm

Print speed

200DPI 1ST (Max): 275 mm/s

200DPI 2ST(Max): 150 mm/s

300DPI 1ST (Max): 180 mm/s

300DPI 2ST (Max): 100 mm/s

RAM memory

SDRAM: 8/32 MB

Flash memory

2MB/4MB (depending on the size of font library)

Print head temperature

detection

Thermal resistor

Print head position

detection

Micro switch

Paper/mark detection

Photoelectric/Mechanical photoelectric sensor

Paper near end detection

Photoelectric sensor

Communication interface

USB, RS-232 (optional)

Barcode

Character

Image

Barcode

CODE128, ITF , UPC-A, UPC-E, EAN13, EAN8

CODE39, CODE93, CODABAR, PDF417, GS1, QR

Character set

Standard characters, compressed characters

Optional Asian character set (simplified Chinese, traditional

Chinese, Japanese, Korean)

Character processing

All characters can be enlarged 1 to 6 times vertically and

horizontally.

Rotation print (0°, 90°, 180°, 270°);

Bold, white/black reverse, underline.

Image

BMP bitmap can be downloaded to RAM and FLASH;

Support direct bitmap printing

Media

Paper type

Continuous paper/marked paper

Paper roll OD

Max.300mm

Core ID

ф10-60mm

Paper thickness

55～100 um

Thermal layer

Outward / Inward

Power consumption

+24V power supply, at

room temperature, average

value

2.5A

PRESENTER

Paper out detection

Photoelectric sensor

Paper out speed

600~1000 mm/s

Retraction detection

Photoelectric sensor

Retraction speed

≥1000mm/s

Paper out mode

Retraction/holding/closing/ejection/throw-out (optional)

BK-T680 User’s Manual

Reliability

Print head lifetime

≥100Km

Cutter lifetime

≥1, 000, 000 (65μm thick thermal paper)

MTBF

360,000 hours (main board)

Environmental

requirements

Operating environment

0～50℃, 20～90%RH(40℃)

Storage environment

-40～60℃, 20～93% RH(40℃)

Physical features

Overall size

161(L) X 123.2(W) X 120.9(H)

(excluding paper holder, paper roll, including control board)

Weight

About 1.8 Kg (excluding paper roll and paper holder)

Notes:

DPI: dots per inch. (1 inch≈25.4 mm);

The real print speed is related to data transmission speed, print darkness, print duty ratio, control

commands and power supply voltage, etc. The print speed may be lower than the value in the

above table.

PRESENTER is a mechanism used to accommodate paper at the front end of the printer.

2.2 Paper specifications

Paper type: continuous paper/marked paper

Paper supply mode: paper roll

Paper width: 48~82.5±0.5 mm

Paper thickness: 55um～100um

Thermal layer: outward / inward

Paper roll specifications:

Optional core ID: ф10-60mm

Max. paper roll OD: ф300mm

2.2.1 Recommended paper:

1) Recommended continuous paper specifications:

Paper model

Manufacturer

TF50KS－E2C

Nippon Paper Industries Co., Ltd.

F240AC/F220-VP

Mitsubishi Paper Mill CO., LTD.

KF060-FEAH

NEW OJI Paper CO., LTD.

F70NA

FUJI PHOTO FILM CO., LTD.

FV230A1

MITSUBISHI PAPER MILL CO., LTD.

2) Recommended marked paper specifications:

The marked paper should not only meet the requirements for standard paper, but also meet the following

requirements:

Mark position

User can select the position of mark (located on thermal layer/non-thermal layer);

When selecting mark, it is recommended to use the following parameters:

L1 mark width: 8mm≤L1≤paper width

L2 mark height: 4mm≤L2≤8mm

L3 mark interval: 58mm≤L3≤305mm

BK-T680 User’s Manual

The reflectivity of marks is no more than 10%; the reflectivity of other parts of the ticket within

mark width along paper feeding direction is no less than 75%.There should be no character or

pattern such as advertisement between two marks.

Notes:

Because of paper shaking in paper feeding and paper parameter difference, the mark position

may have a tolerance of ±1mm;

The mark height can be set by adjusting the printer configuration.

Caution:

Please use the recommended paper or its equivalents. Using other types of paper may affect print

quality and even reduce the print head lifetime;

Do not stick the paper to the paper roll core;

If the print paper is contaminated by chemical or oil, it may discolor or be less heat sensitive,

which will greatly affect the print quality;

Do not rub the paper surface with a nail or hard metal, otherwise it may discolor;

When the temperature goes up to 70℃, paper will discolor. So please be careful of the effect of

temperature, humidity and sunlight.

Indice

Altri manuali Shandong Stampante

Shandong

Shandong BTP-R880NP Manuale utente

Shandong

Shandong BTP-R580 Manuale utente

Shandong

Shandong BTP-2002NP Manuale utente

Shandong

Shandong BT-T080 plus Manuale del proprietario

Shandong

Shandong BT-T080R Manuale del proprietario

Shandong

Shandong BTP-2002NP Manuale del proprietario

Shandong

Shandong U80II Manuale utente

Shandong

Shandong BTP-M280 Manuale utente

Shandong

Shandong BTR-R980 Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente