Sharp PN-L602B Manuale utente
PN-TPC2W7A
User Guide
Version –1
Getting Started
1
Getting Started
Introduction to PN-TPC2W7A
The PN-TPC2W7A is a full-featured High Definition PC based upon Intel
H67®architecture, and powered by an Intel®G620 Pentium®Dual-
core CPU. Targeted for Commercial applications such as interactive
digital signage, the PN-TPC2W7A has been optimized for reliable
operation with Sharp® PN-L series touch-screen displays. The PN-
TPC2W7A includes the Sharp Pen Software™application pre-installed
on the hard disk. It also has the flexibility to run most third party
software and custom applications. The PN-TPC2W7A supports true
1080P video with hardware assisted support for formats such as
MPEG2, H.264 and WM9. The PN-TPC2W7A was designed with display
integration in mind and features a full complement of video outputs
including HDMI®and DVI. The unit also includes an RS232 port for
display control and a custom mounting bracket specially designed to
attach behind a Sharp PN-L series touch screen display. The PN-
TPC2W7A’s all metal chassis and small size make it ideal for
commercial applications requiring a powerful yet compact PC.
Package Contents
The packing box should contain the following
items:
Technovare™PN-TPC2W7A
AC Power Adapter
Mounting Kit
HDMI Cable
Connection Diagram
This Users Guide
Getting Started
2
Federal Communications Commission (FCC)
Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instructions contained in
this manual, may cause harmful interference to radio and television
communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from that of the
receiver
Consult the dealer or an experienced audio/television technician
NOTES:
Connecting this device to peripheral devices that do not comply with Class B
requirements, or using an unshielded peripheral data cable, could also result in
harmful interference to radio or television reception.
The user is cautioned that any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to operate this
equipment. To ensure that the use of this product does not contribute to
interference, it is necessary to use shielded I/O cables.
Getting Started
3
Specifications
Chipset
oIntel®H67
Size
oMini-ITX form factor
oCase: 7.5x 7.4x 1.75
Microprocessor support
oIntel®G620 2.6 GHz Pentium®Dual-Core CPU
Operating systems:
oSupports Windows®XP®32bit/64bit, Windows Vista®
32bit/64bit, and Windows®7®32bit/64bit
oSupports Linux®
oWindows 7 Pro installed
Software Installed:
oSharp®Pen Software™Application
oMicrosoft®Internet Explorer®
oMicrosoft PowerPoint®Viewer
oWindows Media®Player
oQuickTime®Player
oAdobe®Flash® Player Plug-in
System Memory support
oSupports DDR3 1333/1066
oSupports up to 16GB (2 x 8GB)
o2GB installed –both slots occupied and need to remove
the current memory modules to upgrade
USB 2.0 Ports
oSupports hot plug and play
oFour USB 2.0 ports (rear panel ports)
oTwo onboard USB headers for four extra ports
oSupports USB 2.0 protocol up to 480 Mbps transmission
rate
Hard Disk Drive
o2.5” 160GB SATA
Onboard Serial ATA II/III
oSupports 1x SATA II (300 MB/s transfer rate)
oSupports 2x SATA III (600 MB/s transfer rate)
oRear panel e-SATA
oSupports hot plug and Native Command Queuing
On board Realtek 8111E Gigabit LAN Chip
oSupports 10/100/1000Mbps operation
o1 x RJ45 LAN Port
Specifications
4
Specifications (con’t)
Onboard Audio
oRealTek™ ALC888S High-Definition audio chip
oSupports up to 8-channel (2/4/5.1/7.1-channel)
o8-Channel Audio Ports on Back Panel
oSupports Jack-Sensing function (under Windows)
oSupport for S/PDIF Out Header (Internal)
Green Function
oSupports ACPI (Advanced Configuration and Power
Interface)
oSupports EuP Function
oRTC timer to power-on the system
oAC power failure recovery
oSupports S0 (normal), S1 (power on suspend), S3
(suspend to RAM), S4 (suspend to disk), and S5 (soft - off)
Onboard Graphics support
oIntegrated Intel®GMA HD graphics engine
oDVI-I / HDMI®output support (Dual Header capable)
Integrated HDMI Interface with HDCP
oSupports DVI or HDMI 1.4 interfaces
oSecure digital audio merged from integrated HDA codec
with no external audio signals required
oSupport for HDCP 1.3 using soft or hard HDCP keys
oHDCP encryption support when configured as DVI or HDMI
link without the need for external HDCP key crypto ROM
Dual Head Display Controller
oEach controller can drive same or different display
contents to different resolutions and refresh rates
Expansion Slots
o1 x PCIe 2.0 x16 slot
o1 x COM1 Header
oLow power consumption and power management features
Optional
oWatchdog timer
Environmental
oOperating Temperature: 0° to 40° C
oOperating Humidity: 80% maximum relative humidity,
non-condensing
Power
oInput Voltage: 12V 7A
oPower Dissipation: 84 Watts
Installation
5
Mounting PN-TPC2W7A on Sharp PN-L Series
Displays
1. Before mounting, make sure to turn off the monitor
and remove the AC power.
2. Items needed
Sharp PN-L Series Touch-
Screen Display
PN-TPC2W7A
Mounting Plate
AC Power Adapter
4 x M4 (0.7x10mm) screws
2 x M3 (0.5x5 mm)
Phillips®Screw Driver
3. Attach the mounting plate
There are 8 holes on the
mounting plate, but only use 4
holes to match the monitor’s
mounting holes depending on the
monitor model.
The mounting plate is attached to
the Sharp “PN-L” series display as
in Figure 2.
Secure the mounting plate to the
monitor with four included M4 screws.
*NOTE- Do not use the holes marked with the red x
Figure 1
Figure 2
Installation
6
4. Set the AC power adapter in
place
Place the AC power adapter into
the holder on the right side of
the mounting plate as in Figure
3.
AC power cord faces downward
and the DC power cord to the
PN-TPC2W7A faces upward.
5. Install the PN-TPC2W7A
If you look at the right side of the
PN-TPC2W7A before sliding it into
the mounting plate as in Figure 4,
there are two small slits near the
edges on the PN-TPC2W7A and
two small fingers on either side of
AC power adapter holder on the
mounting plate.
As you slide the PN-TPC2W7A
into the mounting plate, insert
the two fingers into these slits as
in Figure 5.
Figure 4
Figure 3
Figure 5
Installation
7
There are two fingers on the left
side of the mounting plate to
catch the PN-TPC2W7A in place
as shown in Figure 6, and they
need to be tightened with two
include M3 screws.
6. Connect the HDMI video cable and the
USB cable prior to turning on the PN-
TPC2W7A.
7. Finish
Plug in the DC power cord into
the PN-TPC2W7A’s power
connector as in Figure 7.
Figure 7
Figure 6
Installation
8
Rear Connector Layout
Audio Port 2-Channel 4-Channel 5.1-Channel
Blue Line-In Line-In Line-In
Green Line-Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Mic In
Orange N/A N/A Center/Subwoofer Out
Black N/A Rear Speaker Out Rear Speaker Out
Grey N/A N/A N/A
Audio Port 7.1-Channel
Blue Line-In
Green Front Speaker Out
Pink Mic In
Orange Center/Subwoofer Out
Black Rear Speaker Out
Grey Side Speaker Out
LAN Connector (with LED status indicator)
Green/Light Up/Blink = 10 Mbps/Link/Activity
Green and Green/Light Up/Blink = 100 Mbps/Link/Activity
Green and Orange/Light Up/Blink = 1000 Mbps/Link/Activity
Installation
9
Rear Connector Layout (con’t)
1. Power Connection (refer to the Rear Connector Layout on pg. 8)
Use only the AC power adapter supplied with the system.
Input: 100~240V AC 1.3A
Output: 12V DC 7A
Plug the 12V AC/DC adapter (as in the figure 1 above) to the PN-
TPC2W7A’s power input jack (as in the figure 2).
2. Power Button
This button will stay lit if the PN-TPC2W7A is powered on. If the
PN-TPC2W7A doesn’t power up after the AC is connected, then
press this button to power up. If normal Windows shutdown is
not shutting down the PN-TPC2W7A, then press this button for
more than 4 seconds will turn off the PN-TPC2W7A. In this case,
run Disk Cleanup in Windows next time the PN-TPC2W7A is
powered up.
Altri manuali per PN-L602B
5
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Sharp Scrivania
Sharp
Sharp MZ-80A Manuale utente
Sharp
Sharp MZ-3500 Manuale utente
Sharp
Sharp PC-1500A Manuale utente
Sharp
Sharp YO-250M Manuale utente
Sharp
Sharp MZ-80B Manuale utente
Sharp
Sharp MZ-700 Series Guida all'installazione
Sharp
Sharp MZ-800 Manuale per l'uso e la cura
Sharp
Sharp MZ-80B Manuale utente
Sharp
Sharp MZ-80A Manuale utente
Sharp
Sharp PN-TPC1W Manuale utente
Sharp
Sharp Mobilon HC-4000 Manuale utente
Sharp
Sharp MZ-350C Manuale utente
Sharp
Sharp MZ-700 Series Manuale utente
Sharp
Sharp MZ-700 Series Manuale utente
Sharp
Sharp MZ-80B Manuale utente
Sharp
Sharp PC-AX40 Manuale utente
Sharp
Sharp MZ-808 Manuale utente
Sharp
Sharp MZ-80B Guida all'installazione
Sharp
Sharp PC-6220 Manuale utente
Sharp
Sharp MZ-5600 Manuale utente
