Sharp PN-HY501 Manuale utente
PN-HY501 Dismantle Instruction
1
Dismantle Instruction
LCD MONITOR
MODEL
PN-HY501
701
PN-HY501 Dismantle Instruction
2
Table of contents
1. Scope.................................................................................................................. 3
2. Tools for dismantling............................................................................................... 3
3. Dismantle Procedure .............................................................................................. 3
4. Back covers .......................................................................................................... 4
5. Printed circuit boards ............................................................................................. 5
6. Battery................................................................................................................ 5
7. LCD Module .......................................................................................................... 6
8. Capacitors............................................................................................................ 7
9. Parts List ............................................................................................................. 7
PN-HY501 Dismantle Instruction
3
1. Scope
This document describes dismantling instruction according to Annex VII of Directive 2012/19/EU.
2. Tools for dismantling
Below tools are required to dismantle this product.
- Screw Driver
- Nipper
3. Dismantle Procedure
This product can be dismantled by below steps.
1. Remove Back covers (section 4)
2. Remove Printed circuit boards (section 5)
3. Remove Battery (section 6)
4. Dismantle LCD (section 7)
5. Remove Electrolyte Capacitors (section 8)
PN-HY501 Dismantle Instruction
4
4. Back covers
Back cover can be removed by screw driver.
PN-HY501 Dismantle Instruction
5
5. Printed circuit boards
All PWBs can be removed by screw driver.
Main I/F PWB (1pcs) Power PWB (1pcs)
0
T-CON PWB (1pcs)
6. Battery
This model uses only AAA battery for remote control.
Battery can easily be removed.
PN-HY501 Dismantle Instruction
6
7. LCD Module
- LCD Dismantle procedure
1. Remove Rear cover
2. Remove PWBs
3. Remove the Cables
LCD
PN-HY501 Dismantle Instruction
7
8. Capacitors
Electrolyte Capacitors which diameter/height is larger than 25mm is installed on Power PWB.
These capacitors can be removed by using nipper to cut the leads.
On Power PWB
9. Parts List
Parts described in Annex VII of directive 2012/19/EU are as below.
Parts
Note
LCD
50inch LCD module
Printed Circuit Boards
Main I/F PWB
Power PWB
T-CON PWB
Battery
AAA battery
Electrolyte capacitors
(height >25mm, diameter >25mm)
On Power PWB
External electric cables
2 kinds of Power Cord
- for EU
- for UK
Indice
Altri manuali Sharp Monitor
Sharp
Sharp LL-E15G1 Manuale utente
Sharp
Sharp PN-75HC1 Manuale utente
Sharp
Sharp PN-T321 Manuale utente
Sharp
Sharp LL-T1610W Manuale utente
Sharp
Sharp PN-655U Manuale utente
Sharp
Sharp PN-70HC1E Guida utente
Sharp
Sharp PN-65SC1 Guida utente
Sharp
Sharp PN-T321 Guida utente
Sharp
Sharp LL-172G Manuale utente
Sharp
Sharp PN-E602 Manuale utente
Sharp
Sharp PN-465U Manuale utente
Sharp
Sharp PN-L601B Manuale utente
Sharp
Sharp LCD MONITOR Manuale utente
Sharp
Sharp 8M-B80AX1E Manuale utente
Sharp
Sharp LL-T1610W Manuale utente
Sharp
Sharp LC-150M2E Manuale utente
Sharp
Sharp 5030i Manuale utente
Sharp
Sharp PN-L705H Manuale utente
Sharp
Sharp PN-V701 Foglio di istruzioni
Sharp
Sharp LL-T1610W Manuale utente
