Showven SPARKULAR FALL Manuale utente
V1.1
SPARKULAR FALL
USER MANUAL
Showven Technologies Co.,Ltd.
User Manual
SPARKULAR FALL
Safety Considerations
Please read this manual carefully before operating the product.
This manual contains the warranty card, please keep it well.
Sparkular Fall Model No.BT04/BT05
Parameter
Dimension
Weight
Input
Working Power
Working Temperature
Casing
Fountain Height
Interface
Hopper capacity
Hanger Diam
192×208×192mm
6kg
200-240VAC, 50/60Hz (BT04)
100-120VAC, 50/60Hz (BT05)
400w
-10℃~ 50 ℃
Auti-Flaming ABS
2m ~ 7m，Depend on different type of
Composite Ti
Double DMX input interfaces,
Double AC power interfaces
280g
40-60mm
》Never touch the nozzle of SPARKULAR TRIPLE, danger of getting burnt.
》Never touch the sparks which shooting out from the nozzle.
》Unauthorized repair are prohibited, it may cause serious incident.
》Keep SPARKULAR FALL dry and do NOT use in rain or snow.
》Make sure lid of feeding hopper are well covered when use Sparkular Fall. Accidentally Burning of
Composite Ti can only use sands to extinguish. Composite Ti should keep away from moisture and
stored in a dry sealed environment.
》Keep audience and flammable material at a minimum distance of 3m from SPARKULAR FALL and
it’s drop sparks. Make sure sparks shoot out from Sparkular FALL can NOT touch any objects.
》Ensure that children, animals and unauthorized persons don’t have access to the SPARKULAR
FALL.
》Clear material for Sparkular Fall is necessary both before the show and after the show, to clear the
Composite Ti remains in the pipe. Check whether there are Composite Ti aggregate in the nozzle after
each show, if any, please clean it up, or it will affect the shooting effect or even damage Sparkular
Fall.
》The Sparkular FALL power supply cable (sparkular fall power supply EX-cable) maximum allowed
cascade for Sparkular Fall is 6pcs (BT04)/ 3pcs (BT05), exceeded connecting may result in damage
or even cause fire.
》For better heat dissipation, block the air intake and air outlet is prohibited.
》Cover of nozzle of Sparkular Fall is prohibited.
1
Operating Panel:
LCD information display area, showing operate menu and working status of machine.
Light emitting diode display area：
READY：After turning on machine, it will automatically preheat around 5 minutes, when the
"READY" green light turns from flashing into long on, indicates that the machine is ready to work
DMX ：Flashing shows that DMX signal is connected, otherwise is without signal
FAULT：When any malfunction , the light turns on
HEAT ：When the machine is heating, signal light turns on
Bottom Indication Light：
Off：Sparking or Not in preheating
Quick Flashing：Preheating
Long on：Preheated
Slow Flashing：Error warning
Control button area：
MENU：Short press to switch interface, press for 3 seconds can switch to the advanced setup inter-
face.
-：Parameters down
+：Parameters up.
ENTER：Confirm and save parameters.
2
Radio frequency identification area：
Main interface：
Error informations display table：
Setting interface：
Interface
》Composite Ti with RFID card, swiping cards used to identify parameters
and types of granules.
》Please note that granules RFID card can increase the single machine
specific working time. The card is disposable,one card can only use one time.
First line：Display DMX address is “1”.
Second line: Display the present inner core temperature and the temperature progress bar; displays
remianing time is 7 minutes and 24 seconds.
Press “MENU” to enter the Setting interface, press the “MENU” button to enter different options until
you return to the main interface.
Options Range Explanation
Set DMX Address
Wireless Control
Manual Fountain
1-512
ON/OFF
ON/OFF
Set the DMX address,machine become a wireless host and can
send out DMX signal when its address is “1++”.
Wireless function switch,you can match code when shows “ON”
Manual fountain switch , for testing purpose only.
Error Informations Explanation
E0 System IC
E2 Temp. Sensor
E3 P Temp. Over
E4 Time Remain
E5 K Temp. Over
E6 Heat Fail
System error.
Temperature sensor was damaged.
Chassis temperature is too high to shut down.
Insufficient granules or remaining time, please swiping time card.
Inner core temperature is too high to shut down
Heating failed.
Advanced menu：
Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter different
options, press MENU till 3 seconds to return to the main interface.
Options ExplanationRange
Set Temperature
Auto Heat
Density
Mode Selection
Default Parameter
500-610
ON/OFF
70-100
Factory Mode/User Mode
Setup inner Core temperature.
Auto preheat function switch after turning on machine.
Adjust the sparks density.
Factory Mode is factory debugging mode,
User Mode is using mode.
Press “ENTER” to restore all parameters to the
factory settings.
3
》For convenient use, there are power supply cable and power supply ex-cable. Power Supply ex-ca-
ble can achieve multiple devices connected, maximum cascade is 6pcs(BT04)/3pcs(BT05). All power
plugs are industrial plug with lock, it need to toggle snap and rotate when using.
Using the host controller to moniter the working status of Sparku-
lar Fall，to achieve multiple dynamic effects and stable
controlling.Sparkular Fall has high/low level，the height settings
1-5 in host controller is low level,6-10 is high level.Please see the
details in host controller manual.
When using the DMX controller, the system takes 2 channels
》If the remote control cannot work, please check whether wireless function was turn on. Press
MENU to switch to wireless control setting , menu is set to “ON” , press “ENTER”. In this interface, you
can also match code with remote controller.
》Sparkular Fall can controlled by both DMX and remote controller, when there are DMX signal input,
wireless remote controller will not work.
》When using remote controller you need to pull out the antenna.
》After pressing“set”button,press”3 on”button immediately to change to low level，press“3 off”to
change to high level.
Power cable connection：
Host controller mode：
Cable DMX mode：
Wireless remote control mode：
Use:
The First channel
The second channel
0-15
16-135
136-255
60-80
20-40
0-10
240-255
Functions
Functions
Fountain OFF
Low Level Fountain ON
High Level Fountain ON
Clear Material
Emergency Stop
Pre-heat OFF（Disable in Auto-heat）
Pre-heat ON（Disable in Auto-heat）
4
》The first group machines correspond to DMX address “1”, the second group DMX address is “3”,
the third DMX address is “5”, remote controller controls 3 groups of machines. You can also set all
Sparkular Fall address as “1”.
》When the lamp is not lit or becomes weak on the remote controller, please replace the battery. It is
better to take battery out when transporting to prevent consumption of battery power by unmeant
press of button.
Battery model：12V 23A
》When the machine is occasionally not working, may be caused by interference, please press the
start button again.
》Wireless control is easily influenced by interference, it suggests to stay as close to machine as
possible when use remote controller, and machines cannot use metal shielding.
In occasion of strong interference, using the wireless host can avoid interference, ensure
stable control. Enter into Set DMX Address option menu,press “-”when the DMX address is “1”to set
the first unit of Sparkular Fall’s DMX address into “1++”, this machine address is “1”, but it can also
output DMX signal and turns into wireless host Sparkular Fall. Use communication cables to connect
all the Sparkular Fall, the host Sparkular Fall will receive the signal from remote controller and trans-
fer to all other Sparkular Fall via communication cables to realize stable signal transmission.
Attention：In this mode,please don’t connect to other controll mode to prevent from
communication disorder.
Attention：
Wireless host Sparkular Fall mode (requires communication cables):
Hanger and Lifting Ring
nstallation Method：
Consumptive Material Type
Options Instruction：
1 ON
HC8200 Fall length
(Low Level)
MEDIUM 2m
LARGE 3m
LARGE-Ⅰ4m
LARGE-Ⅱ5m
Fall length
(High Level)
3m
4m
5m
7m
Address “1” ON 1 OFF Address “1” OFF
2 ON Address “3” ON 2 OFF Address “3” OFF
3 ON Address “5” ON
（Low Level）3 OFF Address “5” OFF
（High Level）
Set
◆When use different
remote controller
◆Change Levels
CLEAR
◆Automatically clean
material for 3 seconds
◆Start Pre-heat
5 S All Starts 5 seconds 15 S All Starts 15 seconds
30 S All Starts 30 seconds OFF All stop
5
▲Sincere thanks for your choosing our products, you will receive quality service from us.
▲The product warranty period is one year. If there is any quality problems, we can exchangea brand
new same model machine to you within seven days after receiving the product.
▲We will offer free of charge maintenance service for machines which with hardware malfunction
(except for the instrument damage caused by human factors) in warrantyperiod. Please don't repair
machine without factory permission.
★Below situations NOT included in warranty service:
1.Damage caused by improper transportation, usage, management, and maintenance, or damage
caused by human factors;
2.Disassemble, modify or repair products without Showven’s permission;
3.Damage caused by external reasons (lightning strike, power supply etc);
4.Damage caused by improper installation or use;
For product damage not included in warranty range, we can provide paid service.
Invoice and warranty card are necessary when asking for maintenance service from SHOWVEN.
-------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Warranty Instructions
Warranty card
Product Name：Serial NO.：
Maintenance Date:
Purchase Date:
Contact Number:
Address:
Customer Feedback
Information:
Actual malfunction:
Maintenance person:
Maintenance details:
6
Showven Technologies Co., Ltd
Add: BuildingB1,ChangshaECenterNo.18,XiangtaiRoad,LiuyangEconomicDevelopment
Zone,ChangshaCity,410300,HunanProvince,P.R.China.
Tel: +86-731-83833068
Web: www.showven.cn
E-mail: [email protected]
Altri manuali per SPARKULAR FALL
2
Indice
Altri manuali Showven Attrezzatura per DJ
Showven
Showven SONICBOOM X Manuale utente
Showven
Showven uFlamer Manuale utente
Showven
Showven FXcommander Manuale utente
Showven
Showven SPARKULAR FALL Manuale utente
Showven
Showven SPARKULAR PRO BT71 Manuale utente
Showven
Showven SPARKULAR TRIPLE BT51 Manuale utente
Showven
Showven SPARKULAR FALL Manuale utente
Showven
Showven X-F3600 Manuale utente
Showven
Showven Circle Flamer X-F1800 Manuale utente
Showven
Showven uFlamer Manuale utente
Showven
Showven SE-SVBT85 Manuale utente
Showven
Showven SPARKULAR miniFALL BT14 Manuale utente
Showven
Showven SPARKULAR JET Manuale utente
Showven
Showven uFlamer X1800 Manuale utente
Showven
Showven SPARKULAR TRIPLE BT51 Manuale utente
Showven
Showven Sparkular mini BT06 Manuale utente
Showven
Showven SE-SVBT72 Manuale utente
Showven
Showven SPARKULAR BT01 Manuale utente
Showven
Showven PyroSlave X16 Manuale utente
Showven
Showven SPARKULAR JET Manuale utente
