Showven SPARKULAR FALL Manuale utente

USER MANUAL

SPARKULAR FALL

V1.0

2021/03/30

Showven Technologies Co., Ltd

USER MANUAL

SPARKULAR FALL

★Please read this manual carefully before operating this product.

★Warranty card attached in the manual, please keep it well.

▲SAFETY CONSIDERATIONS

\ Never touch the nozzle of SPARKULAR FALL, danger of getting burnt

\ Never touch the sparks which shooting out from the nozzle

\ Unauthorized repair are prohibited, it may cause serious incident

\ Keep SPARKULAR FALL dry and do NOT use in rain or snow

\ Make sure lid of feeding hopper are well covered when use Sparkular Fall. Accidentally

Burning of Composite Ti can only use sands to extinguish. Composite Ti should keep away from

moisture and stored in a dry sealed environment

\ Keep audience and flammable material at a minimum distance of 3m from SPARKULAR FALL

and it’s drop sparks. Make sure sparks shoot out from Sparkular FALL can NOT touch any

objects

\ Ensure that children, animals and unauthorized persons don’t have access to the SPARKULAR

FALL

\ Clear material for Sparkular Fall is necessary both before the show and after the show, to

clear the Composite Ti remains in the pipe. Check whether there are Composite Ti aggregate in

the nozzle after each show, if any, please clean it up, or it will affect the shooting effect or

even damage Sparkular Fall

\ The Sparkular FALL power supply cable (sparkular fall power supply EX-cable) maximum

allowed cascade for Sparkular Fall is 6pcs (BT04)/ 3pcs (BT05), exceeded connecting may result

in damage or even cause fire

\ For better heat dissipation, block the air intake and air outlet is prohibited

\ Cover of nozzle of Sparkular Fall is prohibited

▲Description

SPARKULAR FALL is hanging special effects equipment for indoor/outdoor use to generate daz

zling silver “waterfall” sparks effects. According to different usage scenarios, operator can self

define various types of “water curtain” effects vary from 2m to 7m by use of different types of

HC8200.

▲Technical Specifications

\ MODEL: BT04/BT05

\DIMENSION: 196×208×192mm

\ WEIGHT: 6.0kg

\ VOLTAGE: 220V(BT04)/110V(BT05), 50/60Hz

\ WORK POWER: 500W

\ EFFECT HEIGHT: 2-7m(according to HC8200 type)

\ INTERFACE:3-pin XLR, POWER IN/OUT

\ CONTROL: DMX 2 channels, Wireless Remote

\ ADAPTABLE TRUSS SIZE: 40-60mm

▲Operation Panel

1. LED display area:

READY DMX FAU LT HEAT

READY: After turning on machine, it will automatically preheat around 5 minutes, when the

"READY" green light turns from flashing into long on, indicates that the machine is ready to

work

DMX: Flashing shows that DMX signal is connected, otherwise is without signal

FAULT: When any malfunction , the light turns on

HEAT: When the machine is heating, signal light turns on

2. Control button area:

MENU short press to switch interface, press for 3 seconds can switch to the advanced setup

interface

-: Parameters down

+: Parameters up

ENTER Confirm and save parameters.

3. Bottom Indication Light

Off: Sparking or Not in preheating

Quick Flashing: Preheating

Long on: Preheated

Slow Flashing: Error warning

3. RFID area:

Composite Ti with RFID card, swiping cards used to identify parameters and types of granules.

Please note that granules RFID card can increase the single machine

specific working time. The card is disposable,one card can only use one time

▲Interface

1. Main Interface:

First line: Display DMX address is “1”

Second line: Display the present inner core temperature and the temperature progress bar;

displays remianing time is 7 minutes and 24 seconds

2. Error information:

3. Setting Menu:

Press “MENU” to enter the Setting interface, press the “MENU” button to enter different

options until you return to the main interface

4. Advanced Menu:

Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter

different options, wait 3 seconds to return to the main interface

Error information

Explanation

E0 System IC

Systematic error

E2 Temp. Sensor

Temperature sensor was damaged

E3 P Temp. Over

Chassis temperature is too high to shut

down

E4 Time Remain

Insufficient granules or remaining time,

please swiping time card

E5 K Temp. Over

Inner core temperature is too high to shut

down

E6 Heat Fail

Heating failed

Options

Range

Explanation

Set DMX Address

1-512

Set the DMX address, machine become a

wireless host and can

send out DMX signal when its address is

“1++”

Wireless Control

ON/OFF

Wireless function switch, you can match

code when shows “ON”

Manual Fountain

ON/OFF

Manual fountain switch , for testing

purposes only

Options

Range

Explanation

Set Temperature

500-610

Setup inner Core temperature

Auto Heat

ON/OFF

Auto preheat function switch after turn on

machine

Density

70-100

Adjust the sparks density

Mode Selection

Factory Mode

User Mode

Factory Mode is factory debugging mode,

User Mode is using mode

Default Parameter

Press “ENTER” to restore all parameters to

the factory settings

▲Use

1. Power cable connection

For convenient use, there are power supply cable and power supply ex-cable. Power Supply ex-

cable can achieve multiple devices connected, maximum cascade is 6pcs(BT04)/3pcs(BT05). All

power plugs are industrial plug with lock, it need to toggle snap and rotate when using

2. Host controller mode

Using the host controller to moniter the working status of Sparkular Fall to achieve multiple

dynamic effects and stable controlling.Sparkular Fall has high/low level the height settings 1-5

in host controller is low level,6-10 is high level.Please see the details in host controller manual.

3. Cable DMX mode

When using the DMX controller, the system takes 2 channels

The First channel

Functions

0-15

Firing OFF

16-135

Low Level Fountain ON

136-255

High Level Fountain ON

The second channel

Functions

60-80

Clear Material

20-40

Emergency Stop

0-10

Pre-heat OFF(Disable in Auto-heat)

240-255

Pre-heat ON(Disable in Auto-heat)

4. Wireless remote control mode

If the remote control cannot work, please check whether wireless function was turn on. Press

MENU to switch to wireless control setting , menu is set to ON , press ENTER . In this

interface, you can also match code with remote controller

Sparkular Fall can controlled by both DMX and remote controller, when there are DMX signal

input, wireless remote controller will not work.

When using remote controller you need to pull out the antenna.

After pressing set button,press 3 on button immediately to change to low level press

3 off to change to high level.

1 ON

Address “1” ON

1 OFF

Address “1” OFF

2 ON

Address “3” ON

2 OFF

Address “3” OFF

3 ON

Address “5” ON

（Low Level）

3 OFF

Address “5” OFF

（High Level）

Set

◆When use

different remote

controller

◆Change Levels

CLEAR

◆Automatically

clean material for 3

seconds

◆Start Pre-heat

All Starts 5 seconds

15S

All Starts 15 seconds

30S

All Starts 30

seconds

OFF

All stop

Attention: The first group machines correspond to DMX address “1”, the second group DMX

address is “3”, the third DMX address is “5”, remote controller controls 3 groups of machines.

You can also set all Sparkular Fall address as “1”

When the lamp is not lit or becomes weak on the remote controller, please replace the battery.

It is better to take battery out when transporting to prevent consumption of battery power by

unmeant press of button Battery model 12V 23A

When the machine is occasionally not working, may be caused by interference, please press the

start button again

Wireless control is easily influenced by interference, it suggests to stay as close to machine as

possible when use remote controller, and machines cannot use metal shielding

5. Wireless host Sparkular Fall mode (requires communication cables):

In occasion of strong interference, using the wireless host can avoid interference, ensure

stable control. Enter into Set DMX Address option menu,press “-”when the DMX address is

“1”to set the first unit of Sparkular Fall’s DMX address into “1++”, this machine address is “1”,

but it can also output DMX signal and turns into wireless host Sparkular Fall. Use

communication cables to connect all the Sparkular Fall, the host Sparkular Fall will receive the

signal from remote controller and transfer to all other Sparkular Fall via communication cables

to realize stable signal transmission

Attention: In this mode,please don’t connect to other controll mode to prevent from

communication disorder

HC8200

Fall length(Low Level)

Fall length(High Level)

MEDIUM

LARGE

LARGE-Ⅰ

LARGE-Ⅱ

Warranty Instructions

▲Sincere thanks for your choosing our products, you will receive quality service from us

▲The product warranty period is one year. If there are any quality problems within 7

days after shipping out from our factory, we can exchange a brand new same model

machine for you

▲We will offer free of charge maintenance service for machines which with hardware

malfunction (except for the instrument damage caused by human factors)in warranty

period. Please don't repair machine without factory permission

Below situations NOT included in warranty service:

1. Damage caused by improper transportation, usage, management, and maintenance, or

damage caused by human factors;

2. Disassemble, modify or repair products without permission;

3. Damage caused by external reasons (lightning strike, power supply etc.)

4. Damage caused by improper installation or use;

For product damage not included in warranty range, we can provide paid service.

Invoice and warranty card are necessary when applying for maintenance service from

SHOWVEN.

Warranty Card

Product Name:

Serial No.

Purchase Date:

Tel:

Address:

Info. feedback

about the

problem:

Actual problem:

Maintenance

detail:

Service Engineer:

Service Date:

Altri manuali per SPARKULAR FALL

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Showven Attrezzatura per DJ

Showven

Showven SONICBOOM JET Manuale utente

Showven

Showven SPARKULAR WAVER Manuale utente

Showven

Showven uFlamer Manuale utente

Showven

Showven SPARKULAR FALL Manuale utente

Showven

Showven SPARKULAR mini Manuale utente

Showven

Showven Sparkular Manuale utente

Showven

Showven uFlamer Manuale utente

Showven

Showven uFlamer X1800 Manuale utente

Showven

Showven uFlamer Gasboom Manuale utente

Showven

Showven uFlamer PF10 Manuale utente

Showven

Showven SPARKULAR JET Manuale utente

Showven

Showven uFlamer Volcano Manuale utente

Showven

Showven SPARKULAR FALL Manuale utente

Showven

Showven SPARKULAR JET Manuale utente

Showven

Showven SPARKULAR BT01 Manuale utente

Showven

Showven SPARKULAR TRIPLE BT51 Manuale utente

Showven

Showven X-F3600 Manuale utente

Showven

Showven Circle Flamer X-F1800 Manuale utente

Showven

Showven SPARKULAR SPIN BT81 Manuale utente

Showven

Showven uFlamer Manuale utente

Showven

Showven SPARKULAR miniFALL BT14 Manuale utente

Showven

Showven SE-SVBT72 Manuale utente

Showven

Showven Circle Flamer X-F1800 Manuale utente

Showven

Showven SPARKULAR TRIPLE BT51 Manuale utente

Manuali Attrezzatura per DJ popolari di altre marche

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuale del proprietario

Chauvet

Chauvet OVATION E-930VW Manuale utente

Zumtobel

Zumtobel APHRODITE Home Manuale utente

Snow Masters

Snow Masters Zig Oscillator Manuale utente

EuroLite

EuroLite 50530554 Manuale utente

Beamz

Beamz BUV243 Manuale utente

thomann

thomann Stairville DJ Lase 40-G MK-III Manuale utente

Eagletone

Eagletone 6 Eyes Flower Manuale utente

EuroLite

EuroLite FLD-1508 Manuale utente

Technical Pro

Technical Pro LG8xSEA Manuale utente

JB Systems

JB Systems Lounge Laser DMX Manuale utente

Lightmaxx

Lightmaxx Vega Halo 90 Manuale utente

Elation

Elation FUZE WASH Z350 Manuale utente

Maverick

Maverick MK3 WASH Manuale utente

Infinity

Infinity TF-260C7 Fresnel Manuale utente

Chauvet

Chauvet EVE E-50Z Manuale utente

Eliminator Lighting

Eliminator Lighting E 138 Manuale utente

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuale utente