Shure BLX1 Manuale utente
audio ready group
(A-Y)
channel
(0-9)
power
BLX88
audio ready group
(A-Y)
channel
(0-9)
audio ready group
(A-Y)
channel
(0-9)
power
BLX4
channel group
-10 dB
group
(A-Y)
channel
(0-9)
©2012 Shure Incorporated
27A16035 (Rev. 2)
BLX Wireless System
1
BLX
System Components
Note: Your system comes with a combination of the fol-
lowing components.
• BLX1 Bodypack Transmitter
• BLX2 Handheld Transmitter (choice of SM58,
BETA58A, or PG58)
• BLX4 Wireless Receiver
• BLX88 Dual Wireless Receiver
• PS21 Power Supply
• Lavalier microphone (choice of PG185, WL185 or
WL93)
• Headworn microphone (choice of PG30 or
WH30-TQG)
• Instrument microphone (BETA98H)
• Guitar cable (WA302)
Front Panel
Features
BLX88
① audio LED
Indicates strength of incoming audio signal: green for
normal and red for overload.
② Ready LED Icon
Green light indicates system is ready for use and
receiving transmitter signal.
③ LED Display
Displays group and channel setting.
④ group and channel Buttons
Scan: Push and release group button to scan for an
open group and channel.
Manual: Push and hold group button to find an open
group. Push and release channel button to find a
channel in the current group.
⑤ power Button
Turns power on or off.
BLX4
audio ready group
(A-Y)
channel
(0-9)
power
BLX88
audio ready group
(A-Y)
channel
(0-9)
audio ready group
(A-Y)
channel
(0-9)
power
BLX4
⑤
① ② ③ ④
①②③ ④⑤
①②③ ④
2
BLX2
① LED Indicator
Displays power and battery status (see table).
② power Button
Push to turn power on or off.
③ group Button
Changes group setting.
④ channel Button
Changes channel and gain setting.
⑤ LED Display
Displays group and channel setting.
⑥ Identification Cap
⑦ Battery Compartment
① AC Adapter Jack
② Adapter Cord Tie-Off
③ XLR microphone output jack MIC out
④ 6.35 mm (1/4") instrument level output jack
instrument out
Note: XLR and 1/4" connectors can be used simultane-
ously. Refer to the output information in Specifications.
BLX1
① LED Indicator
Displays power and battery status (see table).
② power Switch
Toggles power on or off.
③ Audio Gain Adjustment
Gain thumb wheel—located on the inside of
bodypack door.
④ 4-Pin Microphone Input Jack (TA4
connector)
⑤ group Button
Changes group setting.
⑥ channel Button
Changes channel setting.
⑦ LED Display
Displays group and channel setting.
⑧ Antenna
⑨ Battery Compartment
Back Panel
BLX4
BLX88
BLX1
BLX2
channel group
-10 dB
group
(A-Y)
channel
(0-9)
①
②
④
⑤
⑥
⑦
⑧
⑨
③
③ ④
⑥
⑦
⑤
①
②
POWER
MIC OUT
INSTRUMENT OUT
12-18 V
160 mA
①②③ ④
①
②③ ③ ④④
POWER
MIC OUT
INSTRUMENT OUT
12-18 V
160 mA
INSTRUMENT OUT
MIC OUT
3
Transmitter LED Indicators
LED Indicator Status
Green Ready
Rapidly Flashing Amber Controls locked
Solid Red Battery power low (1 hour remaining*)
Flashing Red and shuts off Batteries dead (change batteries to power on transmitter)
*For alkaline batteries only. For rechargeable batteries, solid red means the batteries are dead.
Before you begin, turn off all transmitters and turn on any equipment
(other microphones or personal monitoring systems) that could cause
interference during the performance.
1. Press and release the group button on the receiver.
The receiver scans for the clearest group and proceeds to channel
scan.
Note: If you want to stop the scan, push the group or channel
button.
2. Turn on transmitter and change the group and channel to match the
receiver (See Manually Setting Group and Channel).
Once the receiver is set up, perform an audio check on the
microphone.
Manually Setting Group and Channel
Single System Setup
Receiver Setup
Group (letter)
1. Hold the group button on the receiver until
the display begins to flash.
2. While the display is flashing, press the
group button again to advance to the next
group.
Note: Only the group setting will be dis-
played during the manual setup.
3. Once the desired group is reached, release
the group button. Then the receiver will au-
tomatically perform a channel scan.
Channel (number)
If channel needs to be changed, follow the
same procedure using the channel button
instead of the group button.
group channel
channel
group
group
channel
channel
channel
group
group
channel
group
group
channel
channel
channel
group
group
4
Transmitter Setup
Transmitter group and channel must be manually set to match the receiver.
Group (letter)
1. Press and release the group button on the transmitter to activate the display. Press the group button again and the
display flashes.
2. While the display is flashing, press the group button again to advance to the desired group setting.
Channel (number)
If channel needs to be changed, follow the same procedure using the channel button instead of the group button.
Note: When the group and channel correctly match the receiver, the ready LED on receiver illuminates.
Multiple System Setup
Up to 12 systems can operate simultaneously (band and RF environment dependent).
Important: Set up each system one-at-a-time. Once a receiver and transmitter is tuned to the same group and channel,
leave the transmitter powered on. Otherwise, scans from the other receivers will not detect that channel as occupied. For
the BLX88, be sure to setup both transmitters before progressing to the next receiver.
Turn on any other equipment that could cause interference during the performance so it will be detected during the group
and channel scans in the following steps.
Before you begin system set up, turn all receivers ON and all transmitters OFF.
For the first receiver:
1. Perform a group scan.
This finds the group with the most clear channels.
Note: For the BLX88, the group scan sets up both receivers at the same time.
2. Turn on the first transmitter and change the group and channel to match receiver.
3. Leave the transmitter on and continue with the additional systems.
For each additional receiver:
1. Use manual setup to change the receiver to match the group setting of the first receiver. Recall that each time the
group setting is changed, a channel scan is automatically done.
2. Turn on the transmitter and change the group and channel to match the receiver.
3. Leave the transmitter on and continue to the next system.
4. Once all receivers are set up, perform an audio check on all microphones.
Locking and Unlocking Controls
Lock system controls to prevent accidental setting changes or power off.
Transmitter
Turn the transmitter on. Hold the group button, then
press the channel button for approximately 2 seconds.
The LED indicator rapidly flashes amber when locked and
green when unlocked.
Receiver
Turn the receiver on. Simultaneously press the group
and channel button to lock or unlock. The display flashes
rapidly.
When locked, the LED display flashes rapidly if any key
is pressed.
The BLX88 can be locked from either side for both sides.
5
Wireless Tips to Improve System Performance
If you encounter wireless interference or dropouts, try the following suggestions:
• Replace the transmitter batteries
• Choose a different frequency channel
• Reposition the antennas so there is nothing obstructing a line of sight to the transmitter (including the audience)
• Avoid placing transmitter and receiver where metal or other dense materials may be present
• Move the receiver to the top of the equipment rack
• Remove nearby sources of wireless interference, such as cell phones, two-way radios, computers, media players, and
digital signal processors
• Keep transmitters more than two meters (6 feet) apart
• Keep the transmitter and receiver more than 5 meters (16 feet) apart
• Keep them away from large metal objects
• During sound check, mark trouble spots and ask presenters or performers to avoid those areas
Getting Good Sound
Correct Microphone Placement
• Hold the microphone within 12 inches from the sound
source. For a warmer sound with increased bass
presence, move the microphone closer.
• Do not cover grille with hand.
Wearing the Headworn Microphone
• Position the headworn microhpone 13 mm (1/2 in.)
from the corner of your mouth.
• Position lavalier and headworn microphones so that
clothing, jewelry, or other items do not bump or rub
against the microphone.
Adjusting Gain
Monitor the audio LED indicator on the receiver front panel when setting the transmitter gain.
• Green: normal levels
• Red: excessive sound levels (overload).
BLX1
Use the thumb wheel on the inside of the bodypack bat-
terydoortoadjustthegainup(+)ordown(−)untildesired
level is reached. For instruments, turn gain to minimum
setting. For lavaliers, increase the gain as desired. The
audio LEDs on the receiver should illuminate when you
speak into the microphone or play your instrument. The
red LED should only illuminate infrequently when you
speak loudly or play your instrument loudly.
BLX2
The BLX2 features two gain level settings, default and
attenuated (-10 dB). The default setting is used for most
situations. If the receiver audio LED flickers red often, set
the microphone to attenuated. Use the channel button to
change the gain setting.
1. Hold down the channel button for 5 seconds.
A dot appears on the lower right-hand corner of the
LEDdisplay,whichindicates−10dBgainsettinghas
been activated.
2. To change the gain back to default, hold the channel
button again for 5 seconds, or until the dot disappears.
13 mm
(.5 in.)
group
(A-Y)
channel
(0-9)
channel group
-10 dB
select
5 s
6
Expected life for AA batteries is up to 14 hours (total
battery life varies depending upon battery type and
manufacturer).
When the LED indicator turns red, it signifies "low battery"
with approximately 60 minutes of remaining battery life.
For alkaline batteries only. For rechargeable batteries,
solid red means the batteries are dead.
To remove batteries from the handheld transmitter, push
them out through the opening in the microphone battery
compartment.
WARNING: Danger of explosion if battery
incorrectly replaced. Operate only with Shure
compatible batteries.
WARNING: Battery packs shall not be exposed
to excessive heat such as sunshine, fire, or
the like.
Wearing the Bodypack
Transmitter
Clip the transmitter to a belt or slide a guitar strap through
the transmitter clip as shown.
For best results, the belt should be pressed against the
base of the clip.
Power Off
Hold down the power button to power off the BLX2 or
BLX4/88. To power off the BLX1, slide the power toggle
switch to OFF.
Removing and Installing
Identification Caps
The BLX2 is equipped with a black identification cap from
the factory (dual vocal systems comes with a black and
gray cap).
To remove: Remove battery cover. Squeeze sides and
pull off cap.
To install: Make sure the tab matches the slot on the bot-
tom of the handheld and click into place. Replace battery
cover.
An optional Identification Cap Kit containing 9 colored
caps is available (see Optional Accessories).
Batteries
Altri manuali per BLX1
1
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Shure Sistema microfonico
Shure
Shure PSM 300 P3RA Manuale utente
Shure
Shure KCX Scheda tecnica
Shure
Shure UHF-R Wireless Manuale utente
Shure
Shure T4 Manuale utente
Shure
Shure ULX-D Manuale utente
Shure
Shure ULX-D Manuale utente
Shure
Shure MXW Series Manuale utente
Shure
Shure U Series Manuale utente
Shure
Shure R90 Manuale utente
Shure
Shure Microflex MXW Manuale utente
Shure
Shure LX Wireless System Manuale utente
Shure
Shure Microflex MX400 Series Manuale utente
Shure
Shure QLXD4E P51 Manuale utente
Shure
Shure ULX-D Manuale utente
Shure
Shure W10BT Manuale utente
Shure
Shure KSM11 Manuale utente
Shure
Shure UHF Wireless System Manuale del proprietario
Shure
Shure T series Manuale utente
Shure
Shure MXW Manuale utente
Shure
Shure UHF-R Wireless Manuale utente
Manuali Sistema microfonico popolari di altre marche
Sennheiser
Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente
Alpha Technologies
Alpha Technologies RBMS Manuale utente
SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 Manuale utente
Panasonic
Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente
Pyle
Pyle PDWM5000 Manuale utente
Airspan
Airspan AS4000 Guida