Shure WL50 Manuale utente

Models WL50 and MC50

User Guide

27A3114 (TF)

2000, Shure Incorporated Printed in U.S.A.

ENGLISH 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGLISH

GENERAL

Shure models WL50 and MC50 are subminiature, electret condenser lavalier microphones. They provide uncompro-

mised sound quality and high reliability with minimal visibility in sound reinforcement applications such as television broad-

casting and stage performances.

Despite its small size, the microphone’s condenser element provides full, clear and natural reproduction of speech. Each

microphone is supplied with two types of equalization caps that are user changeable, allowing for easily customized

sound, and two foam windscreens to minimize wind noise. The supplied mounting accessories consist of a lapel clip,

a tie clip, a pin mount, and a magnet mount, giving the user a wide variety of options for placement.

MODEL VARIATIONS

WL50: Intendedfor wireless use. Connects to Shure wireless bodypack transmitters via a TA4F connector.

WL50X: Suppliedwith a 3 m (10 ft.) stripped and tinned cable for wiring to an alternate connector.

WL50–LO: A lower sensitivity variation of the WL50, supplied with a TA4F connector.

WL50X–LO: A lower sensitivity version of the WL50, supplied with stripped and tinned leads.

MC50: Intended for hardwired applications. WL50 microphone supplied with an in-line preamplifier with a

three-pin male XLR audio connector.

FEATURES



Extended frequency response with user changeable equalization caps for response shaping



Low visibility with a variety of options for mounting



Offered in black, beige, and white with matching accessories



Low handling noise



Legendary Shure quality, ruggedness, and reliability

WINDSCREENS

Two acoustic foam windscreens are supplied to help reduce undesirable wind noise.

EQUALIZATION CAPS

The WL50 and the MC50 are each supplied with two types of equalization caps for high frequency response shaping.

The caps differ in response between 5,000 and 20,000 Hz (see Figure 1 on page 12), and can be distinguished by the

color of their mesh screens. The mild boost equalization cap has a silver mesh screen, while the high boost equalization

cap has a gold mesh screen.

NOTE: For best sound quality, replace the equalization caps if they become clogged with make-up.

USING THE MC50 WITH A MIXER

The preamplifier supplied with the MC50 requires phantom power ranging from 11 to 52 Vdc. Connect the preamplifier

to a mixer input with a minimum load impedance of 800 Ωto maximize operating headroom.

USING THE WL50 WITH OTHER BODYPACK TRANSMITTERS

If connecting the WL50 to anything OTHER than a Shure wireless bodypack, make sure the device provides a regulated

+5 Vdc (130 A minimum) to the red conductor. Refer to the wiring diagrams in Figures 2 and 3 on page 12.

WIRING THE WL50X TO AN ALTERNATE CONNECTOR

ModelWL50X is supplied with a stripped and tinned cable for wiring to a variety of connectors. Refer to the WL50X wiring

diagram in Figure 3 on page 12. For additional information on wiring the WL50X to an alternate connector, contact Shure’s

ApplicationsDepartment at (847) 866–2525 or 1–800–516–2525.

MOUNTING THE MICROPHONE

The WL50 and MC50 microphones come with the following mounting accessories (see Figure 4 on page 13):

Swiveling Lapel Clip. Features a spring-loaded clasp that attaches easily to a necktie, lapel, blouse or shirt, connected

to a rotatable mounting clip. To mount, snap the microphone cable into the clip near the neck of the microphone, then

attach the clasp to an article of clothing. Rotate the mounting clip to place the microphone at desired angle.

Dual Tie Clip. Features a spring-loaded clasp that attaches easily to a necktie or suit coat lapel, and aclip that holds one

or two microphones. To mount, snap the microphone cable(s) into the clip near the neck of the microphone, then attach

the clasp to an article of clothing.

Pin Mount. Features a translucent mounting clip with two straight pins that easily secure to an article of clothing. To

mount, slide the straight pins into clothing, then snap the microphone cable into the mounting clip near the neck of the

microphone.

Magnet Mount. Features a backplate that is worn under clothing and attaches to a magnetic mount capable of holding

one or two microphones. To mount, place the magnetic backplate “necklace” around neck and under clothing, then align

the magnet mount to the backplate and secure it to clothing. Snap microphone cable(s) into the clip near the neck of the

microphone, and adjust the magnet mount to hold microphone at the desired angle.

WARNING: The magnet mount should not be used by persons fitted with an implanted

medical device, such as a pacemaker or defibrillator.

SPECIFICATIONS WL50WL50–LOMC50

Type Condenser (electret bias) Condenser (electret bias) Condenser (electret bias)

Polar Pattern Omnidirectional Omnidirectional Omnidirectional

Output Impedance N/A N/A 136 actual

(rated at 150 )

Recommended Min.

Input Impedance 20 k20 kN/A

Output Level -45.0 dBV/Pa (1 Pa=94 dB SPL) -55.0 dBV/Pa (1 Pa=94 dB SPL) -41.0 dBV/Pa (1 Pa=94 dB SPL)

Maximum SPL 133 dB at 1% THD/1 k ohm load 143 dB at 1% THD/1 k ohm load 138 dB at 1% THD/1 k ohm load

Frequency Response 20 to 20,000 Hz (see Figure 1) 20 to 20,000 Hz (see Figure 1) 20 to 20,000 Hz (see Figure 1)

Dynamic Range 103.0 dB 103.0 dB 108.0 dB

Output Noise

(equivalent SPL,

A-weighted)

30 dB typical;

33 dB maximum 40 dB typical;

43 dB maximum 30 dB typical;

33 dB maximum

Signal-to-Noise

Ratio 64 dB at 94 dB SPL 54 dB at 94 dB SPL 64 dB at 94 dB SPL

SPECIFICATIONS MC50

WL50–LO

WL50

Power

Requirements +5 Vdc on pin 2, return on

pin 1 (ground). +5 Vdc on pin 2, return on

pin 1 (ground). 11 to 52 Vdc (positive on pins 2

and 3, return on pin 1).

Current Drain 60–130 A 60–130 A4.6 mA

Polarity Positive pressure on the dia-

phragm produces a positive volt-

age at pin 3 relative to pin 1 at

the output connector of the mi-

crophone.

Positive pressure on the dia-

phragm produces a positive volt-

age at pin 3 relative to pin 1 at

the output connector of the mi-

crophone.

Positive pressure on the dia-

phragm produces positive volt-

age at pin 2 relative to pin 3 of

the output connector.

Overvoltage

Protection N/A N/A ±75.0 Vdc maximum from pins 2

and 3 to pin 1.

Cap and Overmold

Material Polypropylene Polypropylene Polypropylene

Environmental

Conditions Operating Temperatures:

–18to 57C

0to 135F

Storage Temperatures:

–29to 74C

–20to 165F

Humidity: 0 to 95%

Operating Temperatures:

–18to 57C

0to 135F

Storage Temperatures:

–29to 74C

–20to 165F

Humidity: 0 to 95%

Operating Temperatures:

–18to 57C

0to 135F

Storage Temperatures:

–29to 74C

–20to 165F

Humidity: 0 to 95%

SPECIFICATIONS MC50

WL50–LO

WL50

Packaged Weight 188 g (6.63 oz.) 188 g (6.63 oz.) 305 g (10.76 oz.)

Cable and

Connector 1.5 m (5 ft.), small-diameter,

shielded, with miniature female

4-pin connector (TA4F type).

WL50X: 3 m (10 ft.) small-diam-

eter, shielded, with stripped and

tinned leads.

1.5 m (5 ft.), small-diameter,

shielded, with miniature female

4-pin connector (TA4F type).

WL50X–LO: 3 m (10 ft.) small-

diameter, shielded, with stripped

and tinned leads.

1.5 m (5 ft.), small-diameter,

shielded, with miniature female

4-pin connector (TA4F type).

Microphone

Dimensions See Figure 6. See Figure 6. See Figure 6.

Preamplifier

Dimensions N/A N/A See Figure 5.

Net Weight WL50: 21 g (0.7 oz.) with cable

and connector.

WL50X: 28 g (1.0 oz.) with 3 m

(10 ft.) stripped and tinned cable.

WL50–LO: 21 g (0.7 oz.) with

cable and connector.

WL50X–LO: 28 g (1.0 oz.) with

3 m (10 ft.) stripped and tinned

cable.

121 g (4.3 oz.) with cable, con-

nector, and preamplifier.

SPECIFICATIONS MC50

WL50–LO

WL50

Certification Eligible to bear CE Marking.

Conforms to European EMC Di-

rective 89/336/EEC. Meets ap-

plicable test and performance

criteria in European EMC Stan-

dards ETS300445 (1996), as an

ancillary device.

Eligible to bear CE Marking.

Conforms to European EMC Di-

rective 89/336/EEC. Meets ap-

plicable test and performance

criteria in European EMC Stan-

dards ETS300445 (1996), as an

ancillary device.

Eligible to bear CE marking.

Conforms to European EMC di-

rective 89/336/EEC. Meets ap-

plicable test and performance

criteria in European EMC stan-

dard EN 55103 (1996) parts 1

and 2, for residential (E1) and

light industrial (E2) environ-

ments.

Measured with test circuit (see Figure 7 on page 63).

Measured with RPM626 Preamplifier.

Altri manuali per WL50

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Shure Microfono

Manuali Microfono popolari di altre marche

IK Multimedia

IK Multimedia iRig Stream MIC PRO Manuale utente

DAPAudio

DAPAudio RM-101 Manuale utente

AKG

AKG CHM 21 Manuale utente

Sennheiser

Sennheiser evolution wireless series EM 100 Manuale utente

Sony

Sony C-48 Manuale utente

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Manuale utente

auna PRO

auna PRO MIC-900 Manuale utente

AKG

AKG D 3800 Manuale utente

MAIIN SOUND

MAIIN SOUND IIN style Manuale utente

Earthworks

Earthworks TC25 Manuale utente

Sennheiser

Sennheiser evolution D1 Manuale utente

Alesis

Alesis MicLink Wireless Manuale utente

DSPPA

DSPPA D6234 Manuale utente

Monacor

Monacor IMG STAGELINE ECM-300B Manuale utente

Ansr Audio

Ansr Audio Scan16 Manuale utente

JLab

JLab GO TALK Manuale utente

Renkforce

Renkforce TY-109 Manuale utente

Trust

Trust 31008 Manuale utente