Siemens QVM62.1 Manuale utente

Installation Instructions

Document No. 129-095

September 24, 2009

QVM62.1 Air Velocity Sensor

Item Number 129-095, Rev. AA Page 1 of 3

Product Description

This sensor is used to measure the air velocity in a

duct and provide a 0 to 10V signal to a controller

that is proportional to the velocity. This allows the

controller to maintain a constant airflow in the duct,

balance out pressure fluctuations (supply or exhaust

air control), or just monitor the flow in a duct. The Air

Velocity Sensor is generally used for modulating fan

control in primary applications to set the basic

volume flow.

Product Number

QVM62.1

Warning/Caution Notations

WARNING:

Personal injury/loss of life may

occur if you do not follow the

procedures as specified.

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow the procedures as

specified.

Required Tools

•Pencil

•Hammer

•Center hole punch

•Screwdrivers

•Four - #8 × 1/2-inch sheet metal screws

•Electric drill with 1/8-inch and 7/8-inch

drill bits

Expected Installation Time

45 minutes

Prerequisites

Field wiring must be pulled to installation location.

Installation

Probe Mounting Flange and Sensor

1. Determine the depth of insertion required for

the probe and assemble the extension tube

and/or probe end cap onto the primary sensor

head tube.

NOTE: If the insertion depth required is less

than or equal to 5.7 inches (145 mm)

the extension tube may be removed by

disconnecting the probe cable at the

transducer head, and sliding the

extension tube off the cable. (With the

extension tube installed, the probe’s

depth of insertion is 11.8 inches

[300mm].) If the extension tube is

removed, be sure to reinstall the

probe’s end cap on the cable before

rewiring it to the transducer head.

2. Position the probe mounting flange on the duct

where will be installed. Lightly tap the screw

heads to create drill marks for the mounting

screw holes.

NOTE: Install the sensor in the ductwork in a

location where the airflow is not

turbulent. Do not place it close to

dampers, registers, or bends in

ductwork.

Figure 1. Mounting Locations.

Document No. 129-095

Installation Instructions

September 24, 2009

Page 2 of 3Siemens Industry, Inc.

3. Draw a line between opposite drill marks,

farthest from each other, and make a drill mark

with the punch, at the intersection of the two

lines.

4. Drill four 1/8-inch holes for the mounting screws

at the points labeled “A”, and a 7/8-inch

diameter hole at the point labeled “B” (see

Figure 2).

Figure 2. Mounting Screw Locations.

5. Secure the flange to the duct using the screws

included with the flange and insert the probe into

the duct. Do not tighten the mounting screw at

this time.

Transducer

1. Remove the cover from the transducer head

unit.

2. Hold the base on the duct or structure to which it

is to be mounted and mark the center positions

of the four mounting holes.

NOTE: Make sure there is enough slack in the

probe’s cable so that, if necessary, the

probe can be removed for servicing or

replacement.

3. Make drill hole marks with the punch at the

mounting hole points, and drill four 1/8-inch

holes.

4. Secure the transducer head to its mounting

location with four #8 × 1/2-inch sheet metal

screws.

5. Set jumper for desired airflow range (see

Figure 3).

6. Connect the Field wiring to the transducer head

connector (see Figure 3.)

1 Terminal block for connection to the

immersion stem

2 Terminal block for connection to controller

3 Plug-in unit for setting the three velocity

ranges. The following applies:

No plug-in jumper = 0 to 5 m/s

Plug-in jumper on 1 and 2 = 0 to 10 m/s

(factory setting)

Plug-in jumper on 2 and 3 = 0 to 15 m/s

Figure 3. Wiring and Setting Elements.

7. Reinstall the cover

CAUTION:

The sensor head connections are not

protected against 24 Vac operating

voltage.

If the unit power supply lead being

connected to terminal G is live during

the installation of the sensor, contact

with any of the sensor head terminals

can irreparably damage the unit.

8. Set the probe’s depth of insertion and position

the arrow on the probe cap so that it points in

the direction of the airflow.

9. Tighten the mounting screw located on the side

of the mounting flange (see Figure 4).

The installation is now complete.

Document No. 129-095

Installation Instructions

September 24, 2009

Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as

Industry, Inc.

Siemens Industry, Inc.

Building Technologies Division

1000 Deerfield Parkway

Buffalo Grove, IL 60089-4513

U.S.A.

Tel. +1 847-215-1000

Your feedback is important to us. If you have

comments about this document, please send them

to SBT_technical.editor.us.sbt@siemens.com

Document No. 129-095

Printed in the U.S.A.

Page 3 of 3

Figure 4.

Indice

Altri manuali Siemens Accessori

Siemens

Siemens adm-i12w2 Manuale utente

Siemens

Siemens QFA3100 Manuale di servizio

Siemens

Siemens QMX3.P30 Manuale utente

Siemens

Siemens SIMATIC VS130-2vcr Manuale utente

Siemens

Siemens SIWAREX WL230 BB-S SA Manuale utente

Siemens

Siemens SITRANS FC430 Guida rapida

Siemens

Siemens GAMMA instabus 5WG1 211-2DB01 Manuale di servizio

Siemens

Siemens WiPS-200 Series Manuale utente

Siemens

Siemens Milltronics RBSS Manuale utente

Siemens

Siemens enlighted SU-5i-USB Manuale utente

Siemens

Siemens QNA2 D Series Guida

Siemens

Siemens 6DR4004-6NN Series Manuale utente

Siemens

Siemens SENTRON VL Series Manuale utente

Siemens

Siemens QNA2 D Series Guida

Siemens

Siemens 3VL9400-4PJ00 Manuale utente

Siemens

Siemens QAA2280.xWNC Manuale utente

Siemens

Siemens AP 257/42 Manuale di servizio

Siemens

Siemens RUGGEDCOM WIN7025 Manuale utente

Siemens

Siemens HFPO-11 Manuale utente

Siemens

Siemens 3200 Series Manuale utente

Siemens

Siemens QBM97 Series Manuale utente

Siemens

Siemens SIMATIC VS 110 Manuale utente

Siemens

Siemens RUGGEDCOM WIN7258 Manuale utente

Siemens

Siemens SIWAREX WP321 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuale utente