Siemens SIMATIC NET 6GK7 443-5FX02-0XE0 Manuale utente

IMATIC NET

7-CPs for PROFIBUS

Manual Part B3

CP 443-5 Basic

6GK7 443-5FX02-0XE0 Version 1 and higher (firmware version V4.0 and higher)

for SIMATIC S7-400 / S7-400H

PROFIBUS interface

(9-pin D-sub female

connector)

Mode selector

Status and fault LEDs

Notes on the Product

B3-2 CP 443-5 Basic for PROFIBUS / Manual Part B3

Release 11/2002

C79000-G8976-C161-04

Notes on the Product

Note

All notes in the product information bulletin, which is supplied with this product,

are valid and must be observed.

Compatibility with the Previous Version

Note

Make sure that you read the information regarding extended functionality and

restrictions in Chapter 6 of this manual!

B3-3

CP 443-5 Basic for PROFIBUS / Manual Part B3

Release 11/2002

C79000-G8976-C161-04

Contents

Contents - Part A

PROFIBUS CPs - General Information See General Part. . . . . . . . . . . . . .

Note

Please remember that Part A of the manual also belongs to the description of the

CP. Among other things, it contains explanations of the safety notices, references,

and general information that applies to all S7 CPs for PROFIBUS.

You can also download this general part from the Internet:

http://www4.ad.siemens.de/view/cs/de/8774037

Contents - Part B3

1 Properties / Services B3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Requirements for Use B3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Use with the Current CPU Types B3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Converting older Systems B3-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 Installation and Commissioning B3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 Displays and Mode Selector B3-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 Performance Data B3-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 Supported Transmission Rates B3-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2 Data of S5-Compatible Communication (SEND/RECEIVE Interface)

on FDL Connections B3-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3 Data of FMS Connections B3-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4 Characteristics of S7 Communication B3-14. . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5 Maximum Number of Connections in Total B3-16. . . . . . . . . . . . . . . . . . . . . . .

5.6 Time-of-day Synchronization B3-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7 Use in Fault-Tolerant Systems B3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.8 Other Characteristics B3-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 Compatibility with the Previous Product B3-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1 Extended Functionality Compared with Previous Product B3-19. . . . . . . . . .

6.2 Replacing Older Modules / Replacing Defective Modules B3-20. . . . . . . . . .

7 Technical Specifications B3-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Properties / Services

B3-4 CP 443-5 Basic for PROFIBUS / Manual Part B3

Release 11/2002

C79000-G8976-C161-04

Properties / Services

Application

The CP 443-5 Basic communications processor is designed for use in a SIMATIC

S7-400 (standard) and S7-400H (fault-tolerant system) programmable controller. It

allows the S7-400 / S7-400H to be connected to a PROFIBUS fieldbus system.

Services

The current version of the CP 443-5 Basic supports the following communication

services in the standard and H systems:

SPROFIBUS FMS (complying with EN 50170, FMS client and server function)

as FMS master for the following types of connection:

- MMAC: Master-master acyclic

- MSAC: Master-slave acyclic

- MSAC_SI: Master-slave acyclic with slave initiative

- MSCY: Master slave cyclic

- BRCT (broadcast): Sending to all FMS stations

SS7 communication and PG/OP communication

- PG functions with upload / download of FM modules, configuration /

diagnostics and routing, user programs

Note on routing: Dynamic switchover to alternative paths (for example if

there is a problem on one of the possible transmission paths) is not

supported.

- Operator control and monitoring functions (HMI)

- Data exchange using communication function blocks on S7 connections

(fault-tolerant S7 connections also possible) 1)

Blocks for S7 communication (see also STEP 7 online help or

“System Software for S7-300/400 System and Standard Functions” manual):

BSEND SFB 12

BRCV SFB 13

PUT SFB 14

GET SFB 15

USEND SFB 8

URCV SFB 9

START SFB 19

STOP SFB 20

RESUME SFB 21

STATUS SFB 22

USTATUS SFB 23

CONTROL SFC 62

Properties / Services

B3-5

CP 443-5 Basic for PROFIBUS / Manual Part B3

Release 11/2002

C79000-G8976-C161-04

SS5-compatible communication (SEND/RECEIVE Interface) over FDL

connections of the following types:

- specified FDL connections

- free layer 2 connections

- broadcast

- multicast

STime-of-day synchronization over PROFIBUS

- The CP forwards time-of-day synchronization frames from the LAN to the

station (CPU = time slave) or from the station to the LAN (CPU= time

master) or this station is synchronized via a different LAN and the

time-of-day synchronization frame must be forwarded over PROFIBUS for

the synchronization of further stations.

- Time-of-day status value, standard/daylight saving time switchover,

synchronization status

The services of the CP 443-5 Basic module listed above can be used at the same

time.

Configuration

When configuring, you must use STEP 7 version V5.2 SP1 or higher; for FDL

connections and diagnostic functions, the NCM S7 for PROFIBUS optional

package supplied with STEP 7 must be installed.

If the functionality of the predecessor module is adequate for your purposes,

configuration and diagnostics are also possible with earlier STEP 7 versions.

It is possible to configure over the MPI or LAN/PROFIBUS.

System modifications are possible during operation (H system).

Note

For more detailed information on configuring PROFIBUS CP with STEP 7 /

NCM S7, refer to the manual NCM S7 for PROFIBUS and the online help of

STEP 7.

Programming - Using Blocks

For some communication services, there are “off-the-peg” blocks (FCs/FBs)

available that implement the interface in your STEP 7 user program. You will find a

detailed description of these blocks in the NCM S7 for PROFIBUS manuals.

Properties / Services

B3-6 CP 443-5 Basic for PROFIBUS / Manual Part B3

Release 11/2002

C79000-G8976-C161-04

Notice

We recommend that you always use the latest block versions for all module types.

You will find information on the latest block version and links to download the

current blocks in our Customer Support on the Internet:

http://www4.ad.siemens.de/view/cs/en/8797900

If you are using older block types, this recommendation only applies if you also

have the latest firmware version.

You will find further information and Internet addresses in the Preface of the

General Part of this manual.

Module Replacement without PG

Depending on the setting in the project configuration, the configuration data can

also be stored in the load memory of the CPU. This makes it possible to replace

modules without having to download the configuration data from the PG.

The stored configuration data is protected from power outage by battery backup or

by plugging an EPROM card into the CPU.

Requirements for Use

B3-7

CP 443-5 Basic for PROFIBUS / Manual Part B3

Release 11/2002

C79000-G8976-C161-04

Requirements for Use

The CP 443-5 Basic described here is supported by all the CPU operating systems

listed in the table below.

The chapter also contains the following information:

SThe number of CPs that can be operated with one CPU.

SThe number of AG-SEND or AG-RECV calls on the SEND/RECEIVE interface

that can be active at the same time (data exchange on FDL connections over

PROFIBUS and corresponding connections over Industrial Ethernet).

2.1 Use with the Current CPU Types

When operating the CP 443-5 Basic with the CPU types listed here in the table,

the following functionality is supported without exception:

SNumber of operable CPs: 14

SMulticomputing (except for H systems)

Table 2-1 Use with the Current CPU Types

CPU Order number Firmware version

Number of AG-SEND or AG-RECV

calls at same time

CPU 412 6ES7 412-1XF03-0AB0 As of V3.0 24 / 24

CPU 412-2 6ES7 412-2XG00-0AB0 As of V3.0

CPU414-2 128 KB 6ES7 414-2XG03-0AB0 As of V3.0

CPU414-3 384 KB 6ES7 414-3XJ00-0AB0 As of V3.0

CPU 414-4H 6ES7 414-4HJ00-0AB0 As of V3.0

CPU416-2 0.8 MB 6ES7 416-2XK02-0AB0 As of V3.0 64 / 64

CPU416-3 1.6 MB 6ES7 416-3XL00-0AB0 As of V3.0

CPU 417-4 6ES7 417-4XL00-0AB0 As of V3.0

CPU 417-4H 6ES7 417-4HL00-0AB0 As of V2.1

6ES7 417-4HL01-0AB0 As of V3.0

CPU416F-2 1.6 MB 6ES7 416-2FK02-0AB0 As of V3.1 64 / 64

Requirements for Use

B3-8 CP 443-5 Basic for PROFIBUS / Manual Part B3

Release 11/2002

C79000-G8976-C161-04

2.2 Converting older Systems

The discontinued CPUs listed here in Table 2-2 support the following functionality

in conjunction with the CP 443-5 Basic:

SNumber of operable CPs: 8

SMulticomputing

Table 2-2 Use with Discontinued CPU Types

CPU Order number Version

Number of AG-SEND or AG-RECV

calls at same time

CPU 412 6ES7 412-1XF01-0AB0 2 or higher 12 / 12

6ES7 412-1XF02-0AB0 2 or higher

CPU 413 6ES7 413-1XG01-0AB0 2 or higher

6ES7 413-1XG02-0AB0 1 or higher

CPU 413-2 6ES7 413-2XG01-0AB0 2 or higher

6ES7 413-2XG02-0AB0 1 or higher

CPU414-1 6ES7 414-1XG01-0AB0 2 or higher

6ES7 414-1XG02-0AB0 2 or higher

CPU414-2 128 KB 6ES7 414-2XG01-0AB0 2 or higher

6ES7 414-2XG02-0AB0 2 or higher

CPU414-2 384 KB 6ES7 414-2XJ00-0AB0 4 or higher

6ES7 414-2XJ01-0AB0 2 or higher

CPU416-1 6ES7 416-1XJ01-0AB0 2 or higher 32 / 32

6ES7 416-1XJ02-0AB0 1 or higher

CPU416-2 0.8 MB 6ES7 416-2XK00-0AB0 4 or higher

6ES7 416-1XK01-0AB0 1 or higher

CPU416-2 1.6 MB 6ES7 416-2XL00-0AB0 4 or higher

6ES7 416-2XL01-0AB0 1 or higher

Installation and Commissioning

B3-9

CP 443-5 Basic for PROFIBUS / Manual Part B3

Release 11/2002

C79000-G8976-C161-04

Installation and Commissioning

Procedure / Steps

Table 3-1

Step Explanation / Meaning

1. Insert the CP 443-5

Basic The CP 443-5 Basic can be inserted in all racks with slots for P and K bus

attachment:

SCentral rack CR2

SUniversal rack UR1, UR2 or UR2H

as central rack

as expansion rack with rack no. 1-6

Note

When using the universal rack as an extension rack, you require an IM with a communication bus link!

The CP 443-5 Basic cannot be operated in an ER1 or ER2 expansion rack

(no K bus link possible).

Suitable slots in the rack:

With the exception of the slots reserved for the power supply and IM-R, the

CP 443-5 Basic can be inserted in all slots with a P and K bus interface (in

the central or in an expansion rack no. 1-6).

2. Attachment to

PROFIBUS Note the information in the General section of this manual.

Note

When using the CR2 rack, the CPU and CP must be plugged into the same segment if you want to use

FDL/FMS connections.

3. Configuration Depending on the communication services being used, configuration involves

the following steps:

SNode initialization

This is necessary in all situations. This assigns a PROFIBUS address

and bus parameters to the PROFIBUS CP. For details, refer to /4/

SConfiguring connections:

This is necessary when using the communication services, S7 functions

and FDL connections (SEND/RECEIVE interface). For details, refer to /5/

or /4/.

4. PG/PC Attachment

for Configuration You can connect the PG when configuring the CP as follows:

Svia MPI

Svia LAN / PROFIBUS

The CP 443-5 Basic must already have a PROFIBUS address (for details

of node initialization, refer to /4/).

Displays and Mode Selector

B3-10 CP 443-5 Basic for PROFIBUS / Manual Part B3

Release 11/2002

C79000-G8976-C161-04

Displays and Mode Selector

LEDs Displaying the Status of the CP

The 5 LED indicators on the front panel provide information on the status of the CP

as shown in the table below:

Table 4-1

INTF

(red) EXTF

(red) BUSF

(red) RUN

(green) STOP

(yellow) CP-Betriebszustand

Starting up (STOP->RUN)

Running (RUN)

Stopping (RUN->STOP)

Stopped (STOP)

STOPdue to internal error (for example

CP not configured)

SLoading active in RUN.

SRUN with internal error (e.g. bad

configurattion data)

Waiting for firmware update (duration 10

seconds after power on)

Waiting for firmware update (CP

currently has an incomplete firmware

version).

RUN and PROFIBUS bus errors

Module fault / system error

Key on off flashing

Indice

Altri manuali Siemens Hardware per computer

Siemens

Siemens SIMATIC NET CP 5512 Manuale utente

Siemens

Siemens Fujitsu D1159 Manuale utente

Siemens

Siemens 6GK7343-1EX10-0XE0 Manuale utente

Siemens

Siemens SIMATIC S7 400 Guida utente

Siemens

Siemens SED2 Series Manuale utente

Siemens

Siemens CPU 412-1 Manuale utente

Siemens

Siemens Metro 21 M216KASPC Manuale utente

Siemens

Siemens Simatic M7-400 Manuale utente

Siemens

Siemens SPCN910 Manuale utente

Siemens

Siemens SIMOTION TB30 Manuale utente

Siemens

Siemens CP 1243-8 IRC Manuale utente

Siemens

Siemens TC35i Terminal Manuale utente

Siemens

Siemens PAD-5-CLSA Manuale utente

Siemens

Siemens SIMATIC NET CP 5622 Manuale utente

Siemens

Siemens SIMATIC S7-300 CPU Data: CPU 315-T-2 DP Manuale utente

Siemens

Siemens SENTRON PROFIBUS DPV1 Series Manuale utente

Siemens

Siemens SMN42 Manuale utente

Siemens

Siemens Open Processor Manuale utente

Siemens

Siemens DP/AS-Interface Link 20E Manuale utente

Siemens

Siemens SIMATIC NET CP 443-5 Extended Manuale utente

Siemens

Siemens System 600 APOGEE Manuale utente

Siemens

Siemens Gigaset USB adapter 54 Manuale utente

Siemens

Siemens Gigaset PC Card 108 Manuale utente

Siemens

Siemens TC65 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente