Siemens SCALANCE X-200 Manuale utente
Connect X200
CXG3.X200
Connect X200 for the cloud integration of Siemens Smart infrastructure as well
as third-party systems
● 2-port Ethernet switch for LAN (incl. Daisy Chaining)
● 1-port Ethernet for WAN
● 2 EIA-485 interfaces
● USB interface for 4G dongles
● Operating voltage AC 24 V or DC24V
● Mounting on standard rails or on the wall
● Plug-in screw terminal blocks
● Multi-site management (depending on firmware)
● Remote operation & monitoring (depending on firmware)
● Alarm treatment (depending on firmware)
● Remote tool access, update and configuration via Siemens Cloud Services
(depending on firmware)
A6V11974867_en--_c Smart Infrastructure
2022-08-12
2
Siemens A6V11974867_en--_c
Smart Infrastructure 2022-08-12
Functions
Connect X200 is a gateway and edge device for small or medium size installations serving
as the point of integration for Building Automation and Control Systems smart devices and
cloud applications.
A broad range of devices can be integrated at the system level, for applications such as
HVAC, security, fire safety, power and lighting applications. It supports a wide range of
communication protocols for controllers, meters, sensors, and actuators. These include
BACnet, Modbus and Siemens fire system protocols.
The gateway connects upstream over cable or mobile (4G), and downstream to the local
network over Ethernet or EIA-485 serial bus. Transported data is protected by encryption,
and the device can be managed remotely over a secure tunnel.
The specific set of supported functions may vary according to the region (for example UL
markets) and according to the connected system. Detailed information about the latest
supported functions can be found in the release notes of the installed software.
Type summary
Type Order number Description
CXG3.X200 S55842-Z131-A100 Connect X200
Equipment combinations
Accessories
The accessories listed below are tested but not sold by Siemens Smart Infrastructure.
Manufacturer Type Description
Siemens 6EP3332-6SB00-0AY0 Power supply DC24V/ 2.5A
Verizon USB730L / MC730 4G USB Dongle
Huawei E3372 / E3372h - 153 4G USB Dongle
Huawei E3372 / E3372h - 320 4G USB Dongle
Alcatel IK40V-2AALDE1 4G USB Dongle
Please confirm compatibility of the chosen 4G Dongle according to the infrastructure of your
regional Internet Service Provider before choosing and ordering a specific device (i.e.
compatibility of regional 4G frequency bands). Consult 4G Dongle-Setup (A6V12059208) for
further instructions and information.
3
Siemens A6V11974867_en--_c
Smart Infrastructure 2022-08-12
Technical and mechanical design
The compact build can be mounted on standard rails or walls.
1 Plastic housing
2 LEDs for communication and status
3 Service button
4 a) 2-port Ethernet switch with 2 LEDs per port
4 b) 1-port Ethernet interface with 2 LEDs for WAN
(Internet access)
5 Plug-in terminal blocks with screw terminals
Power supply
6 USB interface for 4G dongles
7 Plug-in terminal blocks with screw terminals
COM1 / COM2
8 DIP switches for bus termination and polarization
(COM1 / COM2)
9 Slider for mounting on standard mounting rails
10 Eyelets for cable ties
11 Holes for wall mounting
12 Date / Series and Serial number
LED indicators
Activity LED / Interface Color Activity Function
Ethernet 1...3 Green Continuously ON
Continuously OFF
Flashing
Link active
No connection
Network traffic
Yellow Continuously ON
Continuously OFF
Link 100 Mbps
Link 10 Mbps
RUN Green Continuously ON
Continuously OFF
Flashing
Device operational
Device not operational
Start-up or program halted
Red Continuously OFF
Continuously ON
Rapid flashing
OK
HW or SW fault - power off and on the X200
Firmware missing/application corrupt
Blue Continuously ON
Continuously OFF
Flashing
Connection to the cloud OK
No connection to the cloud
Onboarding to cloud not finished or device
certificates not updated
APPS Green Continuously OFF
Continuously ON
Flashing
No app(s) installed on the device
Installed app(s) are properly working
Installed app(s) are (re)starting
SVC Red Continuously OFF
Continuously ON
IP address not assigned to LAN port
IP address assigned to LAN port
COM1 / 2 TX Yellow Flashing
Continuously OFF
Communication
No communication to subsystem
COM1 / 2 RX Yellow
Service button Long press, up to
30s (power off
device first)
Press and hold button, restart and wait until
RUN LED is steady green and then release
button. A factory reset will be performed. All
configuration data/installed apps are
deleted.
Short press IP address 169.254.169.254 will be
assigned to LAN port for the duration of 15
min.
4
Siemens A6V11974867_en--_c
Smart Infrastructure 2022-08-12
Product documentation
Notes
Safety
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and property
damage.
● Observe national provisions and comply with the appropriate safety regulations.
Mounting position and ambient temperature
The devices can be snapped onto standard rails or screwed onto a flat surface.
Plug-in screw terminals connect power and interfaces (except for Ethernet).
Ambient temperature -5...50°C (23...122°F) Ambient temperature -5...45°C (23...113°F)
● Wall, horizontal
– From left to right
– From right to left
● Overhead
● Wall, vertically
– From top to bottom
– From bottom to top
● On a horizontal surface
CAUTION
Risk of overheating for failure to comply with ambient temperature
Burning and damage to the device
● Ensure sufficient ventilation to comply with the permissible ambient temperature within
the panel or installation box. The temperature must be at least 10K (18° F) lower
outside the installation box.
Installation
WARNING
Electric shock
Incorrect installation of the device may lead to electric shock injuries when touching the
device!
● Install the device in a lockable cabinet or use terminal covers.
● Do not install the device in locations where children are likely to be present.
● Conductors with a cross-section of 0.5 mm2 (AWG24) or greater shall comply with the
requirements of IEC 60332-1-2 and IEC 60332-1-3 or IEC TS 60695-11-21.
Commissioning / service
NOTICE
When using a 4G dongle
Reboot the device after a 4G dongle has been connected.
For details see 4G Dongle Setup (A6V12059208).
5
Siemens A6V11974867_en--_c
Smart Infrastructure 2022-08-12
Disposal
The device is considered an electronic device for disposal in accordance
with European Directive and may not be disposed of as domestic waste.
● Use only designated channels for disposing the devices.
● Comply with all local and currently applicable laws and regulations.
Technical data
Power supply
Operating voltage 24 V AC (24 V≃, ⏊, ) AC 24V -15 / +20% (SELV / PELV) or
AC 24V Class 2 (US)
48…63 Hz
Operating voltage 24V DC DC 24 V -15 / +20 % (SELV / PELV) or
DC 24V Class 2 (US)
Functional ground(US)
Functional earth
The terminal for the functional ground must be
connected on the installation side with the building
grounding system (PE).
Screw terminals for wire cross sections up to Max. 2.5 mm2 (14 AWG)
Internal fusing 2.5 A irreversible / non-replaceable
External supply line fusing (EU) Non-renewable fuse max. 10A slow
or
circuit breaker max. 13A
Tripping characteristic B, C, D per EN 60898
or
Power supply with current limitation of max. 10A
Power consumption (for supply planning)
Power consumption AC 16VA
Power consumption DC 8W
Function data
Hardware information
Processor NXP i.MX8 DualX
Storage 2 GB RAM
8 GB eMMC
Data backup in the event of power failure
Super cap to support real-time clock (7 days).
Interfaces
Ethernet interfaces
Plug 3 x RJ45, shielded
Interface type 10Base-T / 100Base-TX, IEEE 802.3 compatible
Bit rate 10/100Mbps, autosensing
Protocol BACnet on UDP/IP and HTTPs on TCP/IP
Cabling, cable type 10Mbps: Min. CAT3, shielded cable is recommended
100Mbps: Min. CAT5, shielded cable is recommended
Cable length Max. 100m (330ft)
6
Siemens A6V11974867_en--_c
Smart Infrastructure 2022-08-12
Screw terminals, plug-in
Cu-wire or Cu-strand with wire end sleeve 1 x 0.6mm ∅ to 2.5mm2 (22 to 14AWG)
or 2 x 0.6mm ∅ to 1.0mm2 (22 to 18AWG)
Cu-strand without wire end sleeve 1 x 0.6mm ∅ to 2.5mm2 (22 to 14AWG)
or 2 x 0.6mm ∅ to 1.5mm2 (22 to 16AWG)
Stripping length 6...7.5mm (0.24...0.29 in)
Screwdriver Slot screws, screwdriver size 1 with shaft ø = 3 mm
Max. tightening torque 0.6 Nm (0.44 lb ft)
EIA-485 interfaces
Interface type EIA-485, electrically isolated
Baud rate 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
(depending on the configuration)
Internal bus termination 120 Ohm, switchable with DIP switch
Internal bus polarization 270 Ohm pull-up/pull-down resistances, switchable with
DIP switch
Cabling (in-house cabling only)
Cable length
3-wire cable
Max. 1000 m (3300 ft)
Protection Short-circuit proof
Protection against faulty wiring with AC24V and
DC24V
USB interface (4G internet connection)
Plug Type A
Interface type USB 2.0
Bit rate 480Mbit
Max. load 500mA
Max. cable length 5m
Conformity
Ambient conditions and protection classification
Classification as per EN60730
Automatic action
Control function
Degree of pollution
Overvoltage category
Type 1
Class A
2
I
Protection against electric shock Protection class III
Degree of protection of housing to EN 60529
Front parts in DIN cut-out
Terminal part
IP30
IP20
Climatic ambient conditions
● Storage / Transport (packaged for transport) as per
IEC EN 60721-3-1 / IEC EN60721‑3‑2
● Operation as per IEC/EN 60721-3-3
● Class 1K22 / 2K12
Temperature -25...70°C (-13...158°F)
Air humidity 5...95% (non-condensing)
● Class 3K23
Temperature -5...50°C (23...122°F)
(for details see chapter Mounting)
Air humidity 5...95% (non-condensing)
Mechanical ambient conditions
● Transport per IEC/EN 60721-3-2
● Operation as per IEC/EN 60721-3-3
● Class 2M4
● Class 3M11
Standards, directives and approvals
Product standards EN 60730-1 and EN 62368-1
Product family standard EN 50491-x
7
Siemens A6V11974867_en--_c
Smart Infrastructure 2022-08-12
Standards, directives and approvals
Electromagnetic compatibility (EMC) For residential, commercial, and
industrial environments
EU conformity (CE) See CE declaration 1)
EAC compliance Eurasian compliance
RCM conformity See RCM declaration 1)
UL/cUL approbation (US / Canada) UL916; http://ul.com/database
CSA certification C22.2, http://csagroup.org/services-industries/product-
listing
Environmental compatibility 1) The product environmental declaration 1) contains data
on environmentally compatible product design and
assessments (RoHS compliance, materials
composition, packaging, environmental benefit,
disposal).
1) Documents can be downloaded at https://sid.siemens.com.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
undesired operation
FCC Caution: Changes or modifications not expressly approved by Siemens Switzerland
Ltd. could void user authority to operate the equipment. United States representative
https://new.siemens.com/us/en/products/buildingtechnologies/home.html
Industry Canada statement
This device complies with ISED’s license-exempt RSSs. Operation is subject to the following
two conditions:
1. This device may not cause interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Housing
Housing
Color top/bottom RAL 7035 (light grey) / RAL 7016 (anthracite grey)
Dimensions per DIN 43 880, see dimensions
Weight with/without packaging 350g / 300g
8
Siemens A6V11974867_en--_c
Smart Infrastructure 2022-08-12
Connection terminals
65 66 67 68 69 70
5
AC/DC 24VWANLAN
1B1A 2
6 7
Terminal Symbol Description
1A, 1B 2 x RJ45 interface for Ethernet with switch
LAN (customer network)
2 1 x RJ45 interface for Ethernet
WAN (internet access)
5, 6 ≃ , ⏊, Operating voltage AC 24 V, DC 24 V
7 Functional ground (must be connected on the installation side with the building
grounding system (PE).
USB USB interface for 4G dongles
Term on, off Switch for bus termination
Polar on, off Switch for polarization
65, 66, 67 COM1 Interfaces EIA-485
68, 69, 70 COM2
Warranty
The application-specific technical data is guaranteed only in combination with the Siemens
products listed in the 'Device combinations' section. If third-party products are used, any
guarantee provided by Siemens will be invalidated.
Dimensions
All dimensions in mm and inches
9
Siemens A6V11974867_en--_c
Smart Infrastructure 2022-08-12
124 (4.88")
117 (4.61")
110 (4.33")
129 (5.08")
4.1 (0.16")
144 (5.67")
26.5 (1.04")
45 (1.77")
69.5 (2.73")
74.5 (2.93")
4 (0.16")
21.5 (0.85")
11 (0.43")
45 (1.77") 21.5 (0.85")
11 (0.43")
35.5 (1.40")
49 (1.91")
Issued by
Siemens Switzerland Ltd
Smart Infrastructure
Global Headquarters
Theilerstrasse 1a
CH-6300 Zug
+41 58 724 2424
www.siemens.com/buildingtechnologies
© Siemens Switzerland Ltd, 2022
Technical specifications and availability subject to change without notice.
Document ID A6V11974867_en--_c
Edition 2022-08-12
Altri manuali per SCALANCE X-200
6
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Siemens Portale
Siemens
Siemens SpeedStream 6500 Series Manuale utente
Siemens
Siemens SIMATIC FDE Documento tecnico
Siemens
Siemens FDCW221 Manuale utente
Siemens
Siemens Gigaset SX686 WiMAX Manuale utente
Siemens
Siemens SIMATIC RTLS Series Guida all'applicazione
Siemens
Siemens SIMATIC S7-200 Manuale utente
Siemens
Siemens HG 3500 V4 Manuale utente
Siemens
Siemens ProtoAir FPA-W44 Guida utente
Siemens
Siemens SIMATIC IOT2020 Manuale utente
Siemens
Siemens WTT563 Series Manuale utente
Siemens
Siemens IE/PB LINK PN IO Manuale utente
Siemens
Siemens NK8237 MP4.40 Manuale elenco delle parti
Siemens
Siemens SIMATIC NET IE/WSN-PA Link Guida per l'amministratore
Siemens
Siemens Sinamics Connect Series Manuale utente
Siemens
Siemens Gigaset Optical LAN Adapter Duo Manuale utente
Siemens
Siemens FDCW241 Manuale utente
Siemens
Siemens HiPath HG 1500 Manuale utente
Siemens
Siemens SIMATIC IOT2050 Manuale utente
Siemens
Siemens A53457 Guida alla manutenzione e all'assistenza
Siemens
Siemens SIMATIC IOT2050 Manuale utente
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
