SIGMA TEK IPN 021 Manuale utente
IPN 021
S-DIAS PROFINET I/O Slave
Instruction Manual
Date of creation: 10.03.2015
Version date: 26.07.2023
Article number: 20-103-021-E
Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: +43/6274/4321
Fax : +43/6274/4321-18
Email: office@sigmatek.at
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2014
SIGMATEK GmbH & Co KG
Translation of the Original Instructions
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or
distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.
We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not
responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur
through use of this handbook.
S-DIAS PROFINET I/O SLAVE IPN 021
26.07.2023 Page 1
S-DIAS Profinet I/O Slave Module IPN 021
with 1 Profinet I/O IN
1 Profinet I/O OUT
The S-DIAS Profinet I/O slave module IPN 021 slave module is an
interface module between the S-DIAS control system and PROFINET
bus.
IPN 021 S-DIAS PROFINET I/O SLAVE
Page 2 26.07.2023
Contents
1Introduction............................................................................. 5
1.1 Target Group/Purpose of this Operating Manual......................5
1.2 Important Reference Documentation .........................................5
1.3 Contents of Delivery.....................................................................5
2Basic Safety Directives .......................................................... 6
2.1 Symbols Used...............................................................................6
2.2 Disclaimer......................................................................................8
2.3 General Safety Directives ............................................................9
2.4 Software/Training .......................................................................10
3Standards and Directives......................................................11
3.1 Directives.....................................................................................11
3.1.1 EU Conformity Declaration................................................................11
4Type Plate...............................................................................12
5Technical Data .......................................................................13
5.1 Performance Data.......................................................................13
5.2 Electrical Requirements.............................................................14
5.3 Miscellaneous .............................................................................16
5.4 Environmental Conditions.........................................................16
6Mechanical Dimensions........................................................17
7Connector Layout..................................................................18
S-DIAS PROFINET I/O SLAVE IPN 021
26.07.2023 Page 3
7.1 Status LEDs.................................................................................19
7.2 Applicable Connectors...............................................................20
7.3 Label Field...................................................................................20
8ESD Protection......................................................................21
9Strain Relief ...........................................................................21
10 Assembly/Installation ...........................................................23
10.1 Check Contents of Delivery.......................................................23
10.2 Mounting......................................................................................24
11 Addressing.............................................................................26
12 Supported Cycle Times ........................................................30
12.1 Cycle Times below 1 ms (in µs).................................................30
12.2 Cycle Times equal to or higher than 1 ms (in ms)...................30
13 Hardware Class IPN021 ........................................................31
13.1 Allgemein.....................................................................................32
13.1.1 Communication Interfaces ................................................................ 35
13.2 Global Methods...........................................................................35
13.2.1 GetPDOSizes.................................................................................... 35
13.2.2 GetPDOData..................................................................................... 36
13.2.3 SetPDODat....................................................................................... 36
13.2.4 AddSubModule ................................................................................. 37
13.2.5 InstallCallback................................................................................... 38
IPN 021 S-DIAS PROFINET I/O SLAVE
Page 4 26.07.2023
13.2.6 SendReadAnswer..............................................................................38
13.2.7 SetProcessAlarm...............................................................................39
13.2.8 AddDiagnosisAlarm...........................................................................40
13.2.9 SetDiagnosisAlarm............................................................................40
13.2.10 RemoveDiagnosisAlarm....................................................................41
13.2.11 UpdateStringsInConfig ......................................................................41
13.2.12 Reinitialize.........................................................................................41
13.3 To be noticed...............................................................................41
13.4 Example: Using Callbacks.........................................................42
13.5 Using the GSD File with TIA (Siemens Design Environment) 48
13.6 IPN and Profinet Bus Time Characteristics .............................51
13.6.1 Detail View of IPN021 Timing on the Local S-DIAS Bus ...................52
13.6.2 Detail View of S-DIAS Timing behind VARAN...................................56
14 Transport/Storage..................................................................59
15 Storage ...................................................................................59
16 Maintenance...........................................................................60
16.1 Service.........................................................................................60
16.2 Repair...........................................................................................60
17 Disposal..................................................................................60
S-DIAS PROFINET I/O SLAVE IPN 021
26.07.2023 Page 5
1 Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
•Project planners
•Technicians
•Commissioning engineers
•Machine operators
•Maintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found
on our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
This and additional documents can be downloaded from our website or obtained through
support.
1.3 Contents of Delivery
1x IPN 021
IPN 021 S-DIAS PROFINET I/O SLAVE
Page 6 26.07.2023
2 Basic Safety Directives
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes:
DANGER
Danger indicates that death or serious injury will occur, if the
specified measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the
specified measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
CAUTION
Caution indicates that moderate to slight injury can occur, if the
specified measures are not taken.
To avoid moderate to slight injuries, observe all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
S-DIAS PROFINET I/O SLAVE IPN 021
26.07.2023 Page 7
INFORMATION
Information
Provides important information on the product, handling or
relevant sections of the documentation, which require
attention.
IPN 021 S-DIAS PROFINET I/O SLAVE
Page 8 26.07.2023
2.2 Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual
is regularly checked and required corrections are included in the
subsequent versions. The machine manufacturer is responsible for the
proper assembly, as well as device configuration. The machine
operator is responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If
necessary, contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product
description. It does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this
operating manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused
through, non-compliance with these instructions or applicable
regulations.
Indice
Altri manuali SIGMA TEK Sistema I/O
SIGMA TEK
SIGMA TEK TO 081 Manuale utente
SIGMA TEK
SIGMA TEK DI 080 Manuale utente
SIGMA TEK
SIGMA TEK SDI 101 Manuale utente
SIGMA TEK
SIGMA TEK DI 160 Manuale utente
SIGMA TEK
SIGMA TEK CO 041 Manuale utente
SIGMA TEK
SIGMA TEK DI 200 Manuale utente
SIGMA TEK
SIGMA TEK AI 088-1 Manuale utente
SIGMA TEK
SIGMA TEK SRO 022 Manuale utente
SIGMA TEK
SIGMA TEK C-DIAS Manuale di istruzioni
SIGMA TEK
SIGMA TEK AI 046 Manuale utente
SIGMA TEK
SIGMA TEK SR 012 Manuale utente
SIGMA TEK
SIGMA TEK DM 822 Manuale utente
SIGMA TEK
SIGMA TEK IO 011S Manuale utente
SIGMA TEK
SIGMA TEK AO 081 Manuale utente
SIGMA TEK
SIGMA TEK AI 075 Manuale utente
SIGMA TEK
SIGMA TEK C-DIAS Series Manuale utente
SIGMA TEK
SIGMA TEK DI 204 Manuale utente
SIGMA TEK
SIGMA TEK TO 127 Manuale utente
SIGMA TEK
SIGMA TEK CSTO 082 Manuale utente
SIGMA TEK
SIGMA TEK SDI 101 Manuale utente
Manuali Sistema I/O popolari di altre marche
WAGO
WAGO 750-344 Manuale utente
Teknim
Teknim TWM-1887 Manuale di istruzioni
Intelligent Appliance
Intelligent Appliance IA-2662-E Manuale utente
BERGHOF
BERGHOF ECC DIO 16/16 Manuale di istruzioni
Advantech
Advantech PCM-27J3AU Manuale di installazione e funzionamento
Festo
Festo CP-E08-M12-CL Manuale utente
